《BS-7582-2005.pdf》由会员分享，可在线阅读，更多相关《BS-7582-2005.pdf（10页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS 7582:2005 Code of practice for reconditioning of used safes ICS 13.310 ? Licensed Copy: London South Bank University, London South Bank University, Fri Dec 08 10:47:53 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 7582:2005 This British Standard was published under the authority
2、of the Standards Policy and Strategy Committee on 21 March 2005 BSI 21 March 2005 First edition August 1992 Second edition March 2005 The following BSI references relate to the work on this British Standard: Committee reference GW/2 Draft for comment 03/118535DC ISBN 0 580 45497 5 Committees respons
3、ible for this British Standard The preparation of this British Standard was entrusted to Technical Committee GW/2, Safes, upon which the following bodies were represented: ABI Association of British Insurer Association of Burglary Insurance Surveyors Association of Security Consultants British Banke
4、rs Association British Security Industry Association BRE Building Research Establishment Building Societies Association Car Radio Industry Specialist Association Intellect Master Locksmiths Association Post Office Co-opted members Amendment issued since publication Amd.No.DateComments Licensed Copy:
5、 London South Bank University, London South Bank University, Fri Dec 08 10:47:53 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 7582:2005 BSI 21 March 2005 i Contents Page Committees responsibleInside front cover Forewordii 1Scope1 2Normative references1 3Terms and definitions1 4Reconditioning operat
6、ions1 5Documentation2 6Labelling3 Annex A (informative) Preliminary operations of reconditioning4 Bibliography5 Licensed Copy: London South Bank University, London South Bank University, Fri Dec 08 10:47:53 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 7582:2005 ii BSI 21 March 2005 Foreword This Br
7、itish Standard has been prepared by Technical Committee GW/2, at the request of users, insurers and manufacturers of safes, to provide recommendations for the conduct of operations associated with the reconditioning of used safes. It supersedes BS 7582:1992, which is withdrawn. As a code of practice
8、, this British Standard takes the form of guidance and recommendations. It should not be quoted as if it were a specification and particular care should be taken to ensure that claims of compliance are not misleading. Safe technology changes with time, principally in response to new or improved tool
9、s which have been developed for legitimate purposes but which may reduce the burglary resistance of safes when such tools are used to attack them. The older a safe is, the less likely it is to be capable of protecting its contents against attack with modern tools. Safe manufacturers operate their ow
10、n policies regarding the length of time for which spares are maintained and this affects the age of safes which can be reconditioned using genuine spares. Since such policies vary, and the life of individual products varies also, it is not easy to be specific as to the maximum age of a safe which ma
11、y be reconditioned; whilst shorter time spans may apply, no safe more than 30 years old should be claimed to have been prepared in accordance with this code of practice. NOTEIf the safe and its contents are to be covered by insurance the company concerned may wish to inspect it after reconditioning
12、and establish a maximum level of overnight risk taking account of the safe itself and other circumstances. Safe manufacturers have a duty of care to their customers, past and present, which includes the maintenance of confidentiality regarding the construction details of their safes. Critical inform
13、ation is kept confidential both within and outside safe manufacturing organizations and is released only to bona fide persons. It is inevitable that the wider circulation of information, specifications, drawings etc. will undermine, to some extent, the security of products and safe manufacturers may
14、 decline to co-operate in the provision of information and/or spare parts to unaccredited reconditioning organizations. As a code of practice, this British Standard takes the form of guidance and recommendations. It should not be quoted as if it were a specification and particular care should be tak
15、en to ensure that claims of compliance are not misleading. This new edition of BS 7582 incorporates technical changes only. It does not reflect a full review or revision of the standard, which will be undertaken in due course. This publication does not purport to include all the necessary provisions
16、 of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages 1 to 5 and a back cover. The BSI copyr
17、ight notice displayed throughout this document indicates when the document was last issued. Licensed Copy: London South Bank University, London South Bank University, Fri Dec 08 10:47:53 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 7582:2005 BSI 21 March 2005 1 1 Scope This British Standard gives r
18、ecommendations for the preparation and documentation procedures associated with reconditioned safes. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the lat
19、est edition of the referenced document (including any amendments) applies. BS EN 1143-1:1997, Secure storage units Requirements, classification and methods of test for resistance to burglary Part 1: Safes, strongroom doors and strongrooms. BS EN 14450, Secure storage units Requirements, classificati
20、on and methods of test for resistance to burglary Secure safe cabinets. 3 Terms and definitions For the purposes of this British Standard, the following terms and definitions apply. 3.1 safe secure container for the storage of cash, valuables and data media, providing protection against burglary 3.2
21、 reconditioned safe used safe upon which remedial or cosmetic work has been carried out to restore it, as closely as possible, to its original manufactured specification 3.3 lock case pan cover fitted to the chamber which contains the door boltwork and the lock body 3.4 graded unit safe (see 3.1) ca
22、rrying a label indicating that it has been type-tested and certified to a recognized national or international standard NOTERelevant standards include BS EN 1143-1, BS EN 1143-2 or BS EN 14450. 4 Reconditioning operations 4.1 General The safe should be inspected for evidence of attack or opening fol
23、lowing a lock-out. Any damage to the body or door, especially drilled holes or part holes should be made good to restore the original strength. A check that the door is central in its frame and for wear of hinge pivots should be carried out. NOTE 1Without accepting any legal liability, safe manufact
24、urers may be prepared to offer advice regarding safes of their own manufacture, based on information supplied to them. Any principal working part replaced in reconditioning a safe should be an authentic part supplied by the original manufacturer, or a part of equivalent or better quality where the a
25、uthentic part is unavailable. Where a proprietary item, such as a lock, is part of the original specification of the safe, an identical replacement may be obtained elsewhere. NOTE 2A checklist of the preliminary operations of reconditioning is given in Annex A. It is important that any specific info
26、rmation relating to the reconditioning of a used safe, which could be of assistance in its later compromise, should be the subject of a stringent security discipline by the organization responsible for carrying out the reconditioning operations. A checklist of upgrades should be taped to the rear of
27、 the lock case pan. Licensed Copy: London South Bank University, London South Bank University, Fri Dec 08 10:47:53 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 7582:2005 2 BSI 21 March 2005 4.2 Locks and boltwork All boltwork and locks should be removed from the safe, cleaned, lubricated with graph
28、ite or a similar substance, and reinstated. For key locks, either the levers of the existing lock should be removed and rearranged with new keys cut to the new pattern or a replacement lock of the same or more secure performance should be fitted. On no account should the original number of levers (k
29、ey locks) or wheels (combination locks) be reduced, nor should gate or bridge tolerances be eased. 4.3 Relocking devices Any relocking device should be examined and, if found to be defective or ineffectual, replaced with a new device as close to the original pattern as possible. If the relocking dev
30、ice has wiring and a glass plate, the wire, made of stainless steel/nylon or other material, should be checked for good condition and for capability of operating as intended. The good condition of the glass plate and mountings should also be checked. 4.4 Anchorage points Anchorage points should be e
31、xamined for integrity; if no anchorage point is provided in a safe weighing less than 1 000 kg the safe should be drilled through the base at two separated positions, size permitting, to provide these. The drilled holes should be lined by means of security fitted steel sleeves welded securely into p
32、lace without compromise of any barrier material. The diameter of the drilled hole should not be more than 3 mm larger that the outside diameter of the sleeve. 4.5 Appearance The safe should be repainted and damaged or defective non-critical parts, such as handles, should be replaced with new parts.
33、Badges bearing the re-conditioners name and telephone number should be displayed, bolt numbers should be maintained and be legible. 4.6 Graded units If graded units are forced open due to a lock-out, repairs should only be carried out by a competent practitioner. Any graded units that have been atta
34、cked during a break-in should be scrapped as effective repairs might not be possible. 5 Documentation A reconditioned safe should be accompanied by a certificate giving the following information: a) the name and address of the reconditioning organization; b) the make, size, model, serial number and
35、year of manufacture of the safe, when new; c) the original specification of the safe and any modifications made subsequently to this; d) type and number of locks; e) the date of reconditioning with full details of the work carried out on the safe, including any alternations made, e.g. to the lock pr
36、otection or to the barrier material; f) the name, registered mark and certification reference of any independent third party responsible for approval of the reconditioned safe and/or the competence of the reconditioning organization. If any of the information required under b) and c) is not known, o
37、r is uncertain, a statement to that effect should be made on the certificate. A copy of the certificate should be retained in a secure place by the reconditioning organization. Licensed Copy: London South Bank University, London South Bank University, Fri Dec 08 10:47:53 GMT+00:00 2006, Uncontrolled
38、 Copy, (c) BSI BS 7582:2005 BSI 21 March 2005 3 6 Labelling A label stating that the safe has been reconditioned in accordance with the recommendations of this British Standard should be securely affixed to the inside of the safe door. This label should identify the organization responsible for the
39、conditioning operations and any applicable third party certification relating to the reconditioned safe and/or the reconditioning organization. The date of the reconditioning work should be included on the label in the format month/year, e.g. 08/04. Safes bearing labels claiming compliance with BS E
40、N 1143-1 or BS EN 14450 should be restored to the grade claimed, but no higher grade can be claimed. If the lock specified under the above certification cannot be fitted, the label should be removed. Licensed Copy: London South Bank University, London South Bank University, Fri Dec 08 10:47:53 GMT+0
41、0:00 2006, Uncontrolled Copy, (c) BSI BS 7582:2005 4 BSI 21 March 2005 Annex A (informative) Preliminary operations of reconditioning Preliminary operations before commencing reconditioning should be carried out as follows: 1) Examine the safe for evidence of any previous reconditioning operation, p
42、articularly with respect to the integrity of barrier materials. 2) Open the door with the usual key. 3) Check the operation of the lock with all the available keys. Check operation of combination lock and its changing facility. 4) Check the door frame for alignment and wear. 5) Check the door pivots
43、 for wear. 6) Remove the door casing, check that the lock is correctly fitted and that all transit bolts have been removed. 7) Remove the lock, dismantle it and check the lock components for wear. 8) Check the boltwork for smooth operation and the alignment of rollers or slides, with particular atte
44、ntion to cam operated bolt throwing mechanisms. 9) Check that all ant-explosive devices are operating correctly, and that the glass plate, if fitted, is properly mounted to the original manufacturers specification. 10) Check anti-explosive device wires or cords are not damaged and do not snag with a
45、ny additions or improvements made. 11) Check any labels ensuring they reflect the correct details of the safe i.e. make, model. 12) Check base fixing provision. Licensed Copy: London South Bank University, London South Bank University, Fri Dec 08 10:47:53 GMT+00:00 2006, Uncontrolled Copy, (c) BSI B
46、S 7582:2005 BSI 21 March 2005 Bibliography Standards Publication BS EN 1143-2:2001, Secure storage units Requirements, classification and methods of test for resistance to burglary Part 2: Deposit systems. 5 Licensed Copy: London South Bank University, London South Bank University, Fri Dec 08 10:47:
47、53 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 7582:2005 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is
48、 incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful i
49、f anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications