《BS-EN-10147-1992.pdf》由会员分享，可在线阅读，更多相关《BS-EN-10147-1992.pdf（18页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 10147:1992 Incorporating Amendment Nos. 1 and 2 Specification for Continuously hot-dip zinc coated structural steel strip and sheet Technical delivery conditions The European Standard EN 10147:1991 with the incorporation of its amendment A1:1995 has the status of a British Sta
2、ndard ICS 77.140.50 Licensed Copy: sheffieldun sheffieldun, na, Thu Oct 26 03:44:43 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 10147:1992 This British Standard, having been prepared under the direction of the Engineering Sector Board, was published under the authority of the Standards Board an
3、d comes into effect on 15 June 1996 BSI 04-1999 The following BSI references relate to the work on this standard.: Committee reference ISE/10 Draft for comment 90/39695 DC ISBN 0 580 14999 4 Committees responsible for this British Standard The preparation of this British Standard was entrusted to Te
4、chnical Committee ISE/10, Flat rolled steel products, upon which the following bodies were represented: British Railways Board British Steel Industry Cold Rolled Sections Association Society of Motor Manufacturers and Traders Limited The following bodies were also represented in the drafting of the
5、standard, through subcommittees and panels: British Welded Steel Tube Association Coated Metals Limited Department of the Environment (Property Services Agency) International Tin Research Institute Metal Roof Deck Association National Association of Steel Stockholders Paintmakers Association of Grea
6、t Britain Ltd. Zinc Development Association Amendments issued since publication Amd. No.DateComments 8722May 1996 9639October 1997Indicated by a sideline in the margin Licensed Copy: sheffieldun sheffieldun, na, Thu Oct 26 03:44:43 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 10147:1992 BSI 04-1
7、999i Contents Page Committees responsibleInside front cover National forewordii Foreword 2 Text of EN 101473 National annex NA (informative) Mechanical properties and bend mandrel diameters for material over 3 mm thick11 List of referencesInside back cover Licensed Copy: sheffieldun sheffieldun, na,
8、 Thu Oct 26 03:44:43 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 10147:1992 ii BSI 04-1999 National foreword This British Standard has been prepared by Technical Committee ISE/10 and is the English language version of EN 10147:1991 Continuously hot-dip zinc coated structural steel strip and she
9、et for cold forming Technical delivery conditions. It incorporates amendment 1:1995. Amendment No. 2 is published to correct typographical errors. National annex NA gives the mechanical properties, mandrel diameters and coatings available for continuously hot dip coated flat products over greater th
10、ickness than 3 mm. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Cross-references Publi
11、cations referred toCorresponding British Standard EN 10002-1:1990BS EN 10002 Tensile testing of metallic materials Part 1:1990 Method of test at ambient temperature EN 10025:1993BS EN 10025:1993 Hot rolled products of non-alloy structural steels Technical delivery conditions BS EN 10027 Designation
12、systems for steel EN 10027-1:1992Part 1:1992 Steel names, principal symbols EN 10027-2:1991Part 2:1992 Steel numbers EN 10079:1992BS EN 10079:1993 Definition of steel products EN 10142:1990BS EN 10142:1991 Specification for continuously hot-dip zinc coated low carbon steel sheet and strip for cold f
13、orming: technical delivery conditions EN 10143:1993BS EN 10143:1993 Continuously hot-dip coated steel sheet and strip. Tolerances on dimensions and shape EN 10147:1991BS EN 10147:1992 Specification for continuously hot-dip zinc coated structural steel sheet and strip. Technical delivery conditions E
14、N 10204:1991BS EN 10204:1991 Metallic products. Types of inspection documents EURONORM 12BS 1639:1964 Methods for bend testing of metals Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, the EN tile page, pages 2 to 12, an inside back cover and a back cov
15、er. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Licensed Copy: sheffieldun sheffieldun, na, Thu Oct 26 03:44:43 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORM
16、E EUROPENNE EUROPISCHE NORM EN 10147 November 1991 + A1 June 1995 ICS 77.140.50 Descriptors: Iron and steel products, metal plates, steel strips, structural steels, unalloyed steels, hot-dip galvanizing, continuous coating, delivery conditions, designation, classifications, inspection, tests, markin
17、g English version Continuously hot-dip zinc coated structural steel strip and sheet Technical delivery conditions (includes amendment A1:1995) Bandes et tles en acier de construction galvanises chaud en continue Conditions techniques de livraison (inclut lamendment A1:1995) Kontinuierlich feuerverzi
18、nktes Band und Blech aus Bausthlen Technische Lieferbedingungen (enthlt nderung A1:1995) This European Standard was approved by CEN on 30 November 1991, amendment 1 was approved by CEN on 1995-05-10. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the condit
19、ions for giving this European Standard the status of a national standard without any alteration. It includes Amendment 1:1995 which was approved by CEN on 1995-05-10. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secr
20、etariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the offi
21、cial versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de
22、Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1996 All rights of reproduction and communication in any form and by any means reserved in all countries to CEN and its members Ref. No. EN 10147:1991 + A1:1995 E Licensed Copy: sheffieldun sheffiel
23、dun, na, Thu Oct 26 03:44:43 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 10147:1991+A1:1995 BSI 04-1999 2 Foreword to EN 10147 This European Standard has been prepared by ECISS/TC 27, Surface coated steel flat products, the secretariat of which is held by Normenauschuss Eisen und Stahl (FES) in DI
24、N. It supersedes EURONORM 147 (1979) Continuous hot-dip zinc coated unalloyed steel sheet and coil with specified minimum yield strengths for structural purposes; Quality standard. The European Committee for Iron and Steel Standardization (ECISS) has allocated TC 27 the task of transforming EURONORM
25、 147-79 into a European Standard (EN10147). This European Standard EN 10147 was approved by CEN on 30 November 1991. In accordance with the Common CEN/CENELEC Internal Regulations, the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germ
26、any, Greece, Iceland, Ireland, Italy, Luxembourg, the Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. Foreword to Amendment 1 This Amendment 1 to the European Standard EN 10147 has been prepared by Technical Committee ECISS/TC 27, Surface coated steel flat products, of
27、which the secretariat is held by DIN. During the 14th COCOR meeting on 27 and 28 May 1993 in Brussels ECISS/TC 27 was charged to prepare an amendment of EN 10147 in order to work in the new designations according to EN 10027-1 and ECISS Information Circular IC 10 as well as the steel numbers accordi
28、ng to EN 10027-2. It is intended to issue a second version of EN 10147 as soon as this amendment is adopted. This amendment to European Standard EN 10147 shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 1995, an
29、d conflicting national standards shall be withdrawn at the latest by December 1995. According to the CEN/CENELEC Internal Regulations the following countries are bound to implement this Amendment 1 to European Standard EN 10147: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, I
30、reland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Contents Page Foreword2 1Scope3 2Normative reference3 3Definitions3 4Designation3 5Classification of grades and types of delivery4 6Requirements6 7Testing6 8Marking8 9Packing8 10Storage and t
31、ransportation9 11Disputes9 12Information to be supplied by the purchaser9 Annex A (normative) Reference method for determination of the zinc coating mass10 Annex B (informative) List of corresponding former designations10 Figure 1 Position of the samples for determining the zone coating mass8 Table
32、1 Steel grades and mechanical properties of steels (for thicknesses # 3 mm)4 Table 2 Available coatings, finishes and surface qualities for zinc coatings (Z)5 Table 3 Available coatings, finishes and surface qualities for zinc-iron alloy coatings (ZF)5 Table 4 Coating masses6 Table 5 Bend test for d
33、etermining adhesion of the coating (for product thicknesses # 3 mm)8 Table B.1 List of corresponding designations10 Table NA.1 Steel grade and mechanical properties of steel11 Table NA.2 Available coatings, finishes and surface qualities11 Table NA.3 Bend test for adhesion of coating 11 Licensed Cop
34、y: sheffieldun sheffieldun, na, Thu Oct 26 03:44:43 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 10147:1991+A1:1995 BSI 04-19993 1 Scope 1.1 This European Standard specifies requirements for continuously hot-dip zinc coated flat products in thicknesses # 3,0 mm made of the steels given in Table 1.
35、The thickness is the final thickness of the delivered product after zinc coating. This European Standard applies to strip of all widths and to sheets cut from it ($ 600 mm width) and cut lengths ( 3,0 m. In this case, the mechanical property, adhesion of coating and surface condition requirements sh
36、all also be agreed at the time of ordering. 1.3 The products covered by this European Standard are suitable for applications where the minimum yield strength values and resistance to corrosion are of prime importance. Corrosion protection afforded by the coating is directly proportional to the mass
37、of coating (see also 5.2.2). 1.4 This European Standard is not applicable to continuously hot-dip zinc coated low carbon steel strip and sheet for cold forming (see EN 10142); electrolytically zinc coated cold rolled steel flat products (see EN 10152); continuously organic coated (coil coated) flat
38、steel products (see EN 10169). 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, sub
39、sequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN 10002-1, Metallic materials Tensile testing Part 1: Method of te
40、sting (at ambient temperature). EN 10020, Definition and classification of grades of steel. EN 10021, General technical delivery requirements for steel, and steel products. EN 10027-1, Designation system for steels Part 1: Steel name, principal symbols. EN 10027-2, Designation systems for steels Par
41、t 2: Numerical system. EN 10079, Definition of steel products. EN 10143, Continuously hot-dip metal coated steel sheet and strip tolerances on dimensions and shape. EN 10204, Metallic products types of inspection documents. ECISS IC 10, Designation systems for steel additional symbols for steel name
42、s. EURONORM 12, Bend test for steel sheet and strip less than 3 mm thick1). 3 Definitions For the purposes of this European Standard the following definitions apply in addition to the definitions in EN 10020, EN 10021, EN 10079 and EN 10204 (see clause 2): 3.1 hot-dip zinc coating application of zin
43、c coating by immersing the prepared products in molten zinc. In this case, wide strip of steel is continuously hot-dip coated; the zinc content of the bath shall be at least 99 % 3.2 coating mass total mass including both surfaces (in g/m2) 4 Designation 4.1 The steel names are allocated in accordan
44、ce with EN 10027-1 and ECISS Information Circular IC 10; the steel numbers are allocated in accordance with EN 10027-2. 4.2 The products covered by this European Standard shall be designated as follows in the order given: a) type of product (e.g. strip, sheet or cut length); b) number of this standa
45、rd (EN 10147); c) steel name or steel number and symbol for the type of hot-dip coating as given in Table 1, d) letter indicating the type of coating: 1) Until they are transformed into European Standards, either the EURONORMS listed or the corresponding national standards of this European Standard
46、may be applied. ZZinc coating ZFZinc-iron alloy coating Licensed Copy: sheffieldun sheffieldun, na, Thu Oct 26 03:44:43 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 10147:1991 +A1:1995 4 BSI 04-1999 e) number denoting the nominal mass of coating (e.g. 275 = 275 g/m2 including both surfaces, see Tab
47、le 4), f) letter denoting the coating finish (N, M or R, see Table 2 and Table 3), g) letter denoting the surface quality (A, B or C, see Table 2 and Table 3), h) letter denoting the surface treatment (C, O, CO or U, see 5.5). Examples: Designation of strip made of steel S250GD+Z, coating mass 275 g
48、/m2 (275), coating finish normal spangle (N), surface quality A; surface treatment chemical passivation (C): Designation of sheet made of steel S320GD+ZF, coating mass 100 g/m2 (100), coating finish regular spangle (R), surface quality B, surface treatment oiled (O): 4.3 Where appropriate, additiona
49、l information to the designation as specified in 4.2 shall be given to describe clearly the delivery requirements (see clause 12). 5 Classification of grades and types of delivery 5.1 Steel grades Table 1 gives a summary of the steel grades available. 5.2 Coatings 5.2.1 Zinc (Z) or zinc-iron alloy (ZF) coatings as given in Table 2 and Table 3 are applicable for the products. 5.2.2 The available coating masses given in Table 2 and Table 3 may be supplied. Other coating masses shall be agreed separately at the time