《BS-AU-267-1998.pdf》由会员分享，可在线阅读，更多相关《BS-AU-267-1998.pdf（8页珍藏版）》请在三一文库上搜索。
1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD AUTOMOBILE SERIES BS AU 2
2、67:1998 ICS 43.040.70; 43.100 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Code of practice for Breakaway cables and secondary couplings Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 02:11:23 GMT+00:00 2006, Uncontrolled Copy, (c) BSI
3、 This British Standard, having been prepared under the direction of the Engineering Sector Board, was published under the authority of the Standards Board and comes into effect on 15 November 1998 BSI 1998 The following BSI references relate to the work on this standard: Committee reference AUE/8 Dr
4、aft for comment 96/715576 DC ISBN 0 580 28203 1 BS AU 267:1998 Amendments issued since publication Amd. No.DateText affected Committees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee AUE/8, Undergear for caravans and trailers, upon
5、 which the following bodies were represented: Caravan Club Department of the Environment, Transport and the Regions National Caravan Council Limited National Trailer and Towing Association Ltd. Society of Motor Manufacturers and Traders Limited Licensed Copy: London South Bank University, London Sou
6、th Bank University, Sat Dec 09 02:11:23 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 267:1998 BSI 1998i Contents Page Committees responsibleInside front cover Forewordii 1Scope1 2Terms and definitions1 3Application1 4Design1 5Attachment1 6General2 7Trailer documentation2 Figure 1 Direction of te
7、st load application2 Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 02:11:23 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ii BSI 1998 BS AU 267:1998 Foreword This British Standard has been prepared by Technical Committee AUE/8. As a code of practice, this British
8、 Standard takes the form of guidance and recommendations. It should not be quoted as if it were a specification and particular care should be taken to ensure that claims of compliance are not misleading. EEC Directive 71/320/EEC, Braking requirements and EEC Regulation No. 13, requires the fitting o
9、f a breakaway cable or secondary coupling on all trailers up to a maximum gross weight of 3500 kg. It is now also a requirement of the Construction and Use Regulations that such a device is positively attached to a towing vehicle. A British Standard does not purport to include all necessary provisio
10、ns of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages 1 and 2, an i
11、nside back cover and a back cover. Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 02:11:23 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BSI 19981 BS AU 267:1998 1 Scope This code of practice provides recommendations for breakaway cables and secondary couplings, a
12、nd their attachment points, for light trailers or caravans up to a mass of 3 500 kg. It applies to trailers which do not have brakes or have overrun or inertia type braking systems only. 2 Terms and definitions 2.1 breakaway cable cable between the towing vehicle and the trailer including its fitmen
13、ts which, in the event of separation of the main coupling, activates the braking mechanism of the trailer 2.2 secondary coupling coupling device between the trailer and towing vehicle which, upon separation of the main coupling, ensures that the two vehicles remain connected, prevents the nose of th
14、e drawbar touching the ground and provides residual steering for the trailer 2.3 attachment point fitting (e.g. closed hole, loop or eyelet) provided for the attachment of a breakaway cable or secondary coupling to the towing vehicle 2.4 coupling device, usually made in two parts, which connects the
15、 trailer to the towing vehicle NOTEIt allows for movement, in all axes, of the two vehicles and withstands the applied static and dynamic loads during loading and operation. Typical examples are a coupling head and towball or towing eye and jaw. 3 Application Trailers with a mass of up to 3 500 kg s
16、hould be fitted with either a breakaway cable or a secondary coupling. Trailers without brakes should have a maximum mass of 750 kg and should be fitted with a secondary coupling. It is recommended that trailers with brakes should be fitted with a breakaway cable. 4 Design 4.1 Breakaway cable The br
17、eakaway cable should be capable of applying a sufficient load to the braking system operating mechanism to hold the trailer on at least 18 % gradient at its maximum permissible trailer mass. Upon operation of the breakaway cable, the trailer should be brought to a halt without causing damage to the
18、braking system components as a result of the application of too great an operating force. The breakaway cable should part after application of the trailer brakes either by reason of its ultimate strength or by means of a weak link inserted for this purpose. The cable should be provided with a device
19、 capable of permitting attachment to the attachment point and withstanding the applied loads without failure unless it provides the stress limit feature. The breakaway cable should have sufficient length to enable attachment to be made with the vehicle in any normal towing position without risk of i
20、nadvertent brake application or coming into contact with the ground. In order to ensure the compatibility of the breakaway cable with the braking system only the trailer manufacturers original equipment cable or equivalent should be used. 4.2 Secondary couplings Secondary couplings used for the rete
21、ntion of trailers in the event of main coupling separation should be designed to have an ultimate tensile strength of equivalent to at least twice the maximum permissible mass of the trailer. 5 Attachment 5.1 General The breakaway cable or secondary coupling should be attached to the towbar in accor
22、dance with 5.2 or 5.3. NOTEThe preferred method is by direct attachment, see 5.2. 5.2 Direct attachment The sprung hook or clip on the end of the breakaway cable or secondary coupling should be attached directly to, or through, an attachment point on the towing vehicle. 5.3 Looped over attachment Th
23、e breakaway cable or secondary coupling should be fixed by forming a loop with the hook or clip on the end of the cable which is fixed back on to the cable to form a loop. The loop should then be secured around the towing ball on the vehicle. 5.4 Removable towing devices When the towing device fitte
24、d to the towing vehicle is removable without the use of special tools, then the secondary coupling or breakaway cable should be attached directly to an attachment point, which should not be on, or part of, the detachable component(s). 5.5 Location Attachment points for the breakaway cable or seconda
25、ry coupling should be positioned so that the normal articulation and braking action of the trailer is not impaired. Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 02:11:23 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 2 BSI 1998 BS AU 267:1998 Where possible, the
26、breakaway cable or secondary coupling attachment point(s) should not be more than 100 mm from a vertical plane passing through the longitudinal centre line of the vehicle. If this is not possible, then it is essential that two attachment points are provided, equidistant from the vehicle centre line
27、and no more than 250 mm from the vehicle centre line. The breakaway cable or secondary coupling attachment point(s) should be positioned as far rearward and as high as possible and practicable. 5.6 Physical characteristics When the breakaway cable or secondary coupling is attached directly to the to
28、wbar, the attachment loop, hole, eyelet or similar should be sufficiently large to allow a rigid sphere of at least 10 mm diameter to pass freely through it. 5.7 Strength The breakaway cable or secondary coupling attachment point should be able to withstand a static load of 2D for 10 s, applied alon
29、g a line passing through the centre of the attachment point on a plane parallel to the longitudinal centre line of the vehicle and inclined downwards to the rear at 15 (see Figure 1), without detachment or incurring a distortion of deformation that could affect the safe operation of the breakaway ca
30、ble or secondary coupling (where D is defined in EC Directive 94/20 and limited to a maximum trailer mass of 1500 kg). Figure 1 Direction of test load application 6 General 6.1 Breakaway cables The breakaway cable should pass through a lug, guide or similar fitting on the trailer, to ensure that, re
31、gardless of the relative angles of the trailer and towing vehicle at the time of separation of the main coupling, there is a direct, in line, pull applied to the brake linkage of the trailer. 6.2 Brake mechanism protection If necessary a skid, or other suitable means of protection should be provided
32、 to ensure that the brake operating mechanism does not foul the ground in the event of separation of the main coupling. 7 Trailer documentation Clear instructions and diagrams showing the attachment of the breakaway cable or secondary coupling should be included in the trailer handbook. The trailer
33、handbook should also specify details of the rating and dimensions for spare breakaway cables and secondary couplings. The secondary coupling or breakaway cable attachment point(s) should be identified on the documentation supplied for the towbar installation and operation. The trailer documentation
34、should indicate that direct attachment is the preferred method of attachment but if the cable is to be looped around the towing ball then it is essential that the user ensures that it is secure and will operate correctly. Licensed Copy: London South Bank University, London South Bank University, Sat
35、 Dec 09 02:11:23 GMT+00:00 2006, Uncontrolled Copy, (c) BSI blank Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 02:11:23 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | |
36、 | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body responsible for preparing Brit
37、ish Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is
38、the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front c
39、over. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed
40、 to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range o
41、f information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax
42、: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright sub
43、sists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by a
44、ny means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any ot
45、her purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070. Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 02:11:23 GMT+00:00 2006, Uncontrolled Copy, (c) BSI