《BS-EN-12408-2004.pdf》由会员分享，可在线阅读，更多相关《BS-EN-12408-2004.pdf（14页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 12408:2004 Safety requirements for cableway installations designed to carry persons Quality control The European Standard EN 12408:2004 has the status of a British Standard ICS 03.120.10; 45.100 ? Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 05:24:26 GMT+00:00 2006,
2、Uncontrolled Copy, (c) BSI BS EN 12408:2004 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 28 October 2004 BSI 28 October 2004 ISBN 0 580 44671 9 National foreword This British Standard is the official English language version of EN 12408:20
3、04. The UK participation in its preparation was entrusted to Technical Committee MCE/20, Aerial ropeways, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement interna
4、tional or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purpor
5、t to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee
6、any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 10, an
7、 inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. DateComments Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 05:24:26 GMT+00:00 2006, Uncontrolled Copy, (c) BSI E
8、UROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 12408 October 2004 ICS 03.120.10; 45.100 English version Safety requirements for cableway installations designed to carry persons - Quality control Prescriptions de scurit pour les installations cbles transportant des personnes - Assurance de la qu
9、alit Sicherheitsanforderungen fr Seilbahnen fr den Personenverkehr - Qualittssicherung This European Standard was approved by CEN on 23 August 2004. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status o
10、f a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A versi
11、on in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estoni
12、a, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOM
13、ITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2004 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12408:2004: E Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 05:24:26 GMT+00:00 2006, Uncontrolled C
14、opy, (c) BSI EN 12408:2004 (E) 2 Contents Page Foreword.3 1 Scope5 2 Normative references.5 3 Terms and definitions 5 4 Requirements for quality assurance systems.7 4.1 Product identification and traceability 7 4.2 Control of the production, installation and customer service processes7 5 Additional
15、requirements.7 5.1 General7 5.2 Organizational information8 5.3 Pre-operation inspection8 5.4 Control of non-conforming products 8 Bibliography9 Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 05:24:26 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 12408:2004 (E) 3 Foreword This document (EN 1
16、2408:2004) has been prepared by Technical Committee CEN/TC 242 “Safety requirements for passenger transportation by rope”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement,
17、 at the latest by April 2005, and conflicting national standards shall be withdrawn at the latest by April 2005. This document contains a bibliography. This document forms part of the standards programme approved by the CEN Technical Board on safety requirements for cableway installations designed t
18、o carry persons. This programme comprises the following standards: 1) Safety requirements for cableway installations designed to carry persons Terminology. 2) Safety requirements for cableway installations designed to carry persons General requirements. 3) Safety requirements for cableway installati
19、ons designed to carry persons Calculations. 4) Safety requirements for cableway installations designed to carry persons Ropes. 5) Safety requirements for cableway installations designed to carry persons Tensioning devices. 6) Safety requirements for cableway installations designed to carry persons D
20、rive systems and other mechanical equipment. 7) Safety requirements for cableway installations designed to carry persons Carriers. 8) Safety requirements for cableway installations designed to carry persons Electrical equipment other than for drive systems. 9) Safety requirements for cableway instal
21、lations designed to carry persons Civil engineering works. 10) Safety requirements for cableway installations designed to carry persons Pre-commissioning inspection, maintenance and operational inspection and checks. 11) Safety requirements for cableway installations designed to carry persons Recove
22、ry and evacuation. 12) Safety requirements for cableway installations designed to carry persons Operation. 13) Safety requirements for cableway installations designed to carry persons Quality assurance. Together these form a series of standards regarding design, production, maintenance and operation
23、 of cableway installations designed to carry persons. In respect of ski-tows, the drafting of this document has been guided by the works of the International Organisation for transportation by rope (OITAF). According to the CEN/CENELEC Internal Regulations, the national standards organizations of th
24、e following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 05:24:26 GMT+00:00 2006, Unco
25、ntrolled Copy, (c) BSI EN 12408:2004 (E) 4 Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 05:24:26 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 12408:2004 (E) 5 1
26、 Scope This document specifies the safety requirements applicable to quality assurance for cableway installations designed to carry persons. It sets out provisions for the procedures for quality assurance which supplement the requirements of the other standards cited in the foreword. It is applicabl
27、e to the different cableway systems. This document applies to suppliers of cableway installations designed to carry persons or of safety components for cableway installations designed to carry persons, regardless of whether or not they maintain a quality management system conforming to EN ISO 9001 c
28、ertified by a certification body accredited in accordance with EN 45012. The provisions of clause 4 apply in all cases. In addition, if quality management systems are used, reference shall be made to EN ISO 9001. For the case of suppliers who do not maintain any quality management system in accordan
29、ce with EN ISO 9001, the provisions of this document are to be regarded as minimum requirements. The requirements relating to the traceability of safety components, which are applicable to all suppliers, are intended to facilitate the recall or the investigation of components which threaten to endan
30、ger safety. The requirements in this document are intended to ensure quality and do not replace the technical requirements in standards EN 1709, EN 1908, EN 1909, EN 12927-1, EN 12927-2, EN 12927-3, EN 12927-4, EN 12927-5, EN 12927-6, EN 12927-7, EN 12927-8, EN 12929-1, EN 12929-2, EN 12930, EN 1239
31、7, EN 13107, EN 13223, EN 13243, prEN 13796-1, prEN 13796-2 and prEN 13796-3, but supplement them. This document is not applicable either to cableways for goods transport or to inclined lifts. 2 Normative references The following referenced documents are indispensable for the application of this doc
32、ument. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. prEN 1907:2004, Safety requirements for passenger transportation by rope Terminology. 3 Terms and definitions For the purposes of thi
33、s document, the terms and definitions given in prEN 1907:2004 and the following apply. 3.1 process (of production, assembly, installation, inspection, testing) set of all the resources such as personnel, materials, products, operative methods or practices required for the production, assembly, insta
34、llation, inspection and testing of components 3.2 documentation (of production, assembly, installation, inspection, testing) set of all the documents in which the production, assembly, installation, inspection and testing procedures are described in full detail Licensed Copy: sheffieldun sheffieldun
35、, na, Sat Oct 28 05:24:26 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 12408:2004 (E) 6 3.3 reference designation (of a production, assembly, installation, inspection, testing process) title and reference number or other reference referring to the relevant documents of the production, assembly, ins
36、tallation, inspection or testing procedure 3.4 traceability document document tracing the history of the implementation of all or part of a production, assembly, installation, inspection or testing procedure, and documenting all the results and observations 3.5 specification document defining all th
37、e particular requirements that have to be met for procurement, production, assembly, installation, inspection, testing and, where appropriate, maintenance 3.6 safety component any basic component, set of components, subassembly or complete assembly of equipment and any device incorporated in the ins
38、tallation for the purpose of ensuring a safety function and identified by the safety analysis, the failure of which endangers the safety or health of persons, be they users, operating personnel or third parties NOTE In view of the volume of documentation which may be required for ensuring traceabili
39、ty, it is desirable to distinguish two classes of safety components and to apply different rules to them as a function of their importance for the safety of the installation. 3.6.1 class 1 safety component any basic component, set of components, subassembly or complete assembly of equipment and any
40、device incorporated in the installation for the purpose of ensuring a safety function and identified by the safety analysis, the failure of which by itself endangers the safety or health of persons, be they users, operating personnel or third parties 3.6.2 class 2 safety component any basic componen
41、t, set of components, subassembly or complete assembly of equipment and any device incorporated in the installation for the purpose of ensuring a safety function and identified by the safety analysis, the failure of which in conjunction with the failure of another component (second fault), endangers
42、 the safety or health of persons, be they users, operating personnel or third parties 3.7 traceability in production ability, based on the identification of a component, to locate all the specifications and traceability documents relating to the component 3.8 traceability for recall ability, based o
43、n the identification of a component, to determine its location Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 05:24:26 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 12408:2004 (E) 7 3.9 quality plan document defining, for the purposes of quality assurance, all the specific requirements for o
44、perational procedures, resources and the sequence to be maintained of the activities connected with the design, construction and commissioning of for passenger transportation by rope or with the production, inspection, transportation and installation of Class 1 and 2 safety components 4 Requirements
45、 for quality assurance systems 4.1 Product identification and traceability 4.1.1 For Class 1 safety components, traceability in production and for recall shall be ensured. Traceability documents concerning these components shall be prepared in such a way that it is possible to identify the origin of
46、 the processed materials and of the personnel involved in the individual production stages, the inspection and in the assembly and installation. Here, the reference designations of the production and, if appropriate, of the assembly and installation processes shall also be given. 4.1.2 For Class 2 s
47、afety components, the specifications shall state whether traceability is to be ensured; it shall also be stated whether and to what extent this traceability covers production and/or recall. 4.1.3 The supplier shall introduce documented procedures which shall be kept continuously updated to ensure th
48、at: all components whose traceability is to be ensured receive an identification that remains applicable under normal use; this identification is recorded in the relevant technical documents and these documents are carefully stored; possible non-conformities are avoided during transportation or deli
49、very. 4.2 Control of the production, installation and customer service processes The supplier shall keep available all documents required for assembly and installation. These documents include: an assembly plan explaining the various assembly work and the reference to the processes to be used in conformity with the standard requirements to be met during this work; a test plan describing in detail the tests to be carried out during assembly; a model for