《BS-AU-50-1.5.4A-1994 ISO-10499-1991.pdf》由会员分享，可在线阅读，更多相关《BS-AU-50-1.5.4A-1994 ISO-10499-1991.pdf（10页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS AU 50-1-5.4a:1994 ISO 10499-1: 1991 Incorporating Amendment No. 1 to BS AU 50-5.4:1994 (Renumbers the BS as BS AU 50-5.4a:1994) not published separately Tyres and wheels Part 1: Tyres Section 5: Industrial vehicle tyres Subsection 5.4a Specification for solid tyres (metric series
2、) for pneumatic tyre rims: Designation, dimensions and marking ICS 53.060; 83.160.99 Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 03:40:01 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 50-1-5.4a:1994 This British Standard, having been prepared under the di
3、rection of the Automobile Standards Policy Committee, was published under the authority of the Standards Board and comes into effect on 15 February 1994 BSI 04-1999 The following BSI references relate to the work on this standard: Committee reference AUE/4 Draft for comment 90/76568 DC ISBN 0 580 22
4、806 1 Committees responsible for this British Standard The preparation of this British Standard was entrusted by the Automobile Standards Policy Committee (AUE/-) to Technical Committee AUE/4, upon which the following bodies were represented: Agricultural Engineers Association Automobile Association
5、 British Industrial Truck Association British Pressure Gauge Manufacturers Association British Rubber Manufacturers Association Bus and Coach Council Department of Transport Freight Transport Association Institute of Road Transport Engineers (Inc) Motor Cycle Industrys Association of Great Britain L
6、td. Motor Industry Research Association National Tyre Distributors Association Retread Manufacturers Association Road Haulage Association Ltd. Society of Motor Manufacturers and Traders Ltd. Amendments issued since publication Amd. No.DateComments 10001May 1998Indicated by a sideline in the margin L
7、icensed Copy: London South Bank University, London South Bank University, Sat Dec 09 03:40:01 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 50-1-5.4a:1994 BSI 04-1999i Contents Page Committees responsibleInside front cover National forewordii 1Scope1 2Normative references1 3Definitions1 4Tyre des
8、ignations1 5Marking1 6Tyre dimensions2 7Tyre size range2 Table 1 Nominal rim diameter code1 Table 2 Nominal rim width code1 Table 3 Recommended size range and dimensions for solid tyres for pneumatic tyre rims3 List of referencesInside back cover Licensed Copy: London South Bank University, London S
9、outh Bank University, Sat Dec 09 03:40:01 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 50-1-5.4a:1994 ii BSI 04-1999 National foreword This Subsection of this Part of BS AU 50 has been prepared under the direction of the Automobile Standards Policy Committee and is identical with ISO 10499-1:199
10、1 Industrial tyres and rims Rubber solid tyres (metric series) for pneumatic tyre rims Part 1: Designation, dimensions and marking, including Amendment 1, published by the International Organization for Standardization (ISO). Other Parts of this standard are as follows: Part 2: Wheels and rims; Part
11、 3: Valves; Part 4: Rim profiles and dimensions. The Technical Committee has reviewed the provisions of ISO 3877-4 and ISO 4223-2 to which normative reference is made in the text and has decided that they are acceptable for use in conjunction with this standard. A British Standard does not purport t
12、o include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Cross-references International standardCorresponding British Standard ISO 3739
13、-1:1992BS AU 50 Tyres and wheels Part 1 Tyres Section 5: Industrial vehicle tyres Subsection 5.2:1994 Specification for pneumatic tyres (metric series) on 5 tapered or flat base rims (designation, dimensions and marking) Summary of pages This document comprises a front cover, an inside front cover,
14、pages i and ii, pages 1 to 4, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Licensed Copy: London South Bank University, London South Bank U
15、niversity, Sat Dec 09 03:40:01 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO 10499-1:1991 BSI 04-19991 1 Scope This International Standard specifies the main requirements, including designations, dimensions and markings, of the metric series of rubber solid tyres for pneumatic tyre rims primarily i
16、ntended for industrial machines for use on prepared surfaces. Rim contours fitting these tyres will be specified in a future part of ISO 3739. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this International Standard
17、. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC a
18、nd ISO maintain registers of currently valid International Standards. ISO 3739:1), Industrial tyres and rims Part 1: Pneumatic tyres (metric series) on 5 degrees tapered or flat base rims Designation, dimensions and marking. ISO 3877-4:1984, Tyres, valves and tubes List of equivalent terms Part 4: S
19、olid tyres. ISO 4223-2:1991, Definitions of some terms used in the tyre industry Part 2: Solid tyres. ISO 10499-2:, Industrial tyres and rims Rubber solid tyres (metric series) for pneumatic tyre rims Part 2: Load ratings (To be published). 3 Definitions For definitions of terms relating to solid ty
20、res, see ISO 4223-2; equivalent terms are given in ISO 3877-4. 4 Tyre designations The dimensional and constructional characteristics shall be indicated as follows: 4.1 Nominal section width The nominal section width of the tyre shall be indicated in millimetres, ending either in 0 or 5. 4.2 Nominal
21、 aspect ratio The nominal aspect ratio shall be expressed as a percentage and shall be a multiple of 5. 4.3 Nominal rim diameter code For tyres mounted on existing rims, the code shall be as given in Table 1. Table 1 Nominal rim diameter code 4.4 Nominal rim width code For tyres mounted on existing
22、rims, the code shall be as given in Table 2. Table 2 Nominal rim width code 5 Marking The marking concerning the dimensional and constructional characteristics shall consist of the four-part designation specified in clause 4. The location of the marking of the rim width code may be distinct but shal
23、l be in close proximity to the marking of the other dimensional characteristics. The marking concerning the designation of the service description is specified in ISO 10499-2:. EXAMPLE 225/75 15/6.5 The characteristics of a tyre with the above markings would be as follows: 1) To be published. Nomina
24、l rim diameter codeNominal rim diameter, Dr mm 4102 6152 8203 9229 10254 12305 15381 Nominal rim width code 2.5 3.25 4.0 5.0 6.5 8.0 10.0 225:nominal section width equal to 225 mm; 75:nominal aspect ratio equal to 75; 15:nominal rim diameter code, corresponding to 381 mm; 6.5:nominal rim width code.
25、 Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 03:40:01 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO 10499-1:1991 2 BSI 04-1999 6 Tyre dimensions The specified dimensional data for solid tyres for pneumatic tyre rims are maximum dimensions and shall satisfy
26、the requirements in 6.1 and 6.2. 6.1 The tyre section width shall not exceed the values of design section width for pneumatic tyres of the same size designation as specified in ISO 3739-1. The effective tyre section width of the solid tyres may be substantially less than the specified design section
27、 width. 6.2 The tyre section height shall not exceed the values of design section height for pneumatic tyres of the same size designation as specified in ISO 3739-1. The tyre overall diameter is the sum of the nominal rim diameter, Dr plus twice the tyre section height. 7 Tyre size range The relevan
28、t size range for the recommended metric series of solid tyres for pneumatic tyre rims and their specified maximum dimensions are shown in Table 3. Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 03:40:01 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO 10499-1:199
29、1 BSI 04-19993 Table 3 Recommended size range and dimensions for solid tyres for pneumatic tyre rims Nominal tyre section width Nominal rim diameter code Rim width code Maximum tyre section width Maximum overall diameter mm Nominal aspect ratio mmmm85 %80 %75 %70 %65 % 100 110 125 140 160 180 200 4
30、4 4 4 4 4 4 2.5 3.25 3.25 4.0 4.0 5.0 5.0 98 112 123 141 156 180 195 272 290 314 340 374 408 442 262 278 302 326 358 390 422 252 268 290 312 342 372 402 242 256 278 298 326 354 382 232 246 264 284 310 336 362 100 110 125 140 160 180 200 6 6 6 6 6 6 6 2.5 3.25 3.25 4.0 4.0 5.0 5.0 98 112 123 141 156
31、180 195 322 340 364 390 424 458 492 312 328 352 376 408 440 472 302 318 340 362 392 422 452 292 306 328 348 376 404 432 282 296 314 334 360 386 412 100 110 125 140 160 180 200 225 8 8 8 8 8 8 8 8 2.5 3.25 3.25 4.0 4.0 5.0 5.0 6.5 98 112 123 141 156 180 195 228 373 391 415 441 475 509 543 585 363 379
32、 403 427 459 491 523 563 353 369 391 413 443 473 503 541 343 357 379 399 427 455 483 519 333 347 365 385 411 437 463 495 125 140 160 180 200 225 9 9 9 9 9 9 3.25 4.0 4.0 5.0 5.0 6.5 123 141 156 180 195 228 441 467 501 535 569 611 429 453 485 517 549 589 417 439 469 499 529 567 405 425 453 481 509 54
33、5 391 411 437 463 489 521 160 180 200 225 250 280 10 10 10 10 10 10 4.0 5.0 5.0 6.5 6.5 8.0 156 180 193 228 246 283 526 560 594 636 680 730 510 542 574 614 654 702 494 524 554 592 630 674 478 506 534 570 604 646 462 488 514 546 580 618 160 180 200 225 250 280 315 12 12 12 12 12 12 12 4.0 5.0 5.0 6.5
34、 6.5 8.0 8.0 156 180 195 228 246 283 308 577 611 645 687 731 781 841 561 593 625 665 705 753 809 545 575 605 643 681 725 777 529 557 585 621 655 697 747 513 539 565 597 631 669 715 160 180 200 225 250 280 315 355 15 15 15 15 15 15 15 15 4.0 5.0 5.0 6.5 6.5 8.0 8.0 10.0 156 180 195 228 246 283 308 35
35、7 653 687 721 763 807 857 917 985 637 669 701 741 781 829 885 949 621 651 681 719 757 801 853 913 605 633 661 697 731 773 823 879 589 615 641 673 707 745 791 843 Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 03:40:01 GMT+00:00 2006, Uncontrolled Copy, (c) BSI
36、4 blank Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 03:40:01 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 50-1-5.4a:1994 BSI 04-1999 List of references See national foreword. Licensed Copy: London South Bank University, London South Bank University, Sat
37、Dec 09 03:40:01 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 50-1-5.4a:1994 ISO 10499-1: 1991 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europ
38、e and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our produc
39、ts and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers mem
40、bers an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 700
41、1. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standa
42、rds through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to d
43、ate with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright,
44、 in the UK, of the publications of the internationalstandardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise wit
45、hout prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permis
46、sion of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070. Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 03:40:01 GMT+00:00 2006, Uncontrolled Copy, (c) BSI