《BS-EN-13599-2002.pdf》由会员分享，可在线阅读，更多相关《BS-EN-13599-2002.pdf（22页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 13599:2002 Copper and copper alloys Copper plate, sheet and strip for electrical purposes The European Standard EN 13599:2002 has the status of a British Standard ICS 77.150.30 ? Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 10:12:51 GMT+00:00 2006, Uncontrolled Copy,
2、 (c) BSI BS EN 13599:2002 This British Standard, having been prepared under the direction of the Engineering Sector Policy and Strategy Committee, was published under the authority of the Standards Policy and Strategy Committee on 19 September 2002 BSI 19 September 2002 ISBN 0 580 40425 0 National f
3、oreword This British Standard is the official English language version of EN 13599:2002. It supersedes BS 4608:1970 which is withdrawn. The UK participation in its preparation was entrusted by Technical Committee NFE/34, Copper and copper alloys, to Subcommittee NFE/34/1, Wrought and unwrought coppe
4、r and copper alloys, which has the responsibility to: A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the B
5、SI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for
6、 its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK inte
7、rests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 19 and a back cover. The BSI copyright date displayed in this document indicates when th
8、e document was last issued. Amendments issued since publication Amd. No. DateComments Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 10:12:51 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13599 March 2002 ICS 77.150.30 English version Copper
9、and copper alloys - Copper plate, sheet and strip for electrical purposes Cuivre et alliages de cuivre - Plaques, tles et bandes en cuivre pour usages lectriques Kupfer und Kupferlegierungen - Platten, Bleche und Bnder aus Kupfer fr die Anwendung in der Elektrotechnik This European Standard was appr
10、oved by CEN on 22 February 2002. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nation
11、al standards may be obtained on application to the Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notifi
12、ed to the Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerlan
13、d and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2002 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1
14、3599:2002 E Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 10:12:51 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 13599:2002 (E) Contents page Foreword . . . . . . . . . . . . . . . . . . . . . . . . . . .3 1Scope . . . . . . . . . . . . . . . . . . . . . . . . .4 2Normative references . . .
15、 . . . . . . . . . .4 3Terms and definitions . . . . . . . . . . . . .4 4Designations . . . . . . . . . . . . . . . . . . .5 4.1Material . . . . . . . . . . . . . . . . . . . . . . . .5 4.2Material condition . . . . . . . . . . . . . . . . .5 4.3Product . . . . . . . . . . . . . . . . . . . . . . .
16、.5 5Ordering information . . . . . . . . . . . . .6 6Requirements . . . . . . . . . . . . . . . . . . .7 6.1Composition . . . . . . . . . . . . . . . . . . . . .7 6.2Mechanical properties . . . . . . . . . . . . . .8 6.3Bending characteristics . . . . . . . . . . . . .8 6.4Electrical properties . .
17、. . . . . . . . . . . . .8 6.5Freedom from hydrogen embrittlement . .8 6.6Dimensions and tolerances . . . . . . . . . .8 6.7Edgewise curvature c . . . . . . . . . . . . . .8 6.8Surface condition . . . . . . . . . . . . . . . . .9 7Sampling . . . . . . . . . . . . . . . . . . . . . .9 7.1General . .
18、. . . . . . . . . . . . . . . . . . . . . .9 7.2Analysis . . . . . . . . . . . . . . . . . . . . . . . .9 7.3Mechanical and electrical tests . . . . . . .9 8Test methods . . . . . . . . . . . . . . . . . . .9 8.1Analysis . . . . . . . . . . . . . . . . . . . . . . . .9 8.2Tensile test . . . . . . .
19、. . . . . . . . . . . . . .10 8.3Hardness test . . . . . . . . . . . . . . . . . . . .10 8.4Bend test . . . . . . . . . . . . . . . . . . . . . . .10 page 8.5Electrical resistivity test . . . . . . . . . . . . .11 8.6Hydrogen embrittlement test . . . . . . . . .11 8.7Retests . . . . . . . . . . . .
20、. . . . . . . . . . . .11 8.8Rounding of results . . . . . . . . . . . . . . .11 9Declaration of conformity and inspection documentation . . . . . . . . .11 9.1Declaration of conformity . . . . . . . . . . .11 9.2Inspection documentation . . . . . . . . . . .12 10Marking, packaging, labelling . . .
21、. . . .12 Annex A (informative) Characteristics of coppers for electrical purposes . . . . .17 Bibliography . . . . . . . . . . . . . . . . . . . . . . . . .19 Tables Table 1 Composition of copper . . . . . . . .12 Table 2 Mechanical properties . . . . . . . . .13 Table 3 Electrical properties (at 2
22、0 C) . . .14 Table 4 Tolerances on thickness of plate, sheet and strip . . . . . . . . . . . . . .15 Table 5 Tolerances on width of strip . . . .15 Table 6 Tolerances on width of plate and sheet . . . . . . . . . . . . . . . . . . . . . .16 Table 7 Tolerances on length of plate, sheet and strip cut
23、to length for lengths up to 5 000 mm . . . . . . . . . . . . .16 Table 8 Squareness of cut plate and sheet 16 Table 9 Edgewise curvature c . . . . . . . . .16 Table A.1 Particular characteristics of coppers for electrical purposes . . . . .18 2 Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29
24、10:12:51 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 13599:2002 (E) Foreword This document EN 13599:2002 has been prepared by Technical Committee CEN/TC 133 “Copper and copper alloys“, the Secretariat of which is held by DIN. This European Standard shall be given the status of a national standard,
25、 either by publication of an identical text or by endorsement, at the latest by September 2002, and conflicting national standards shall be withdrawn at the latest by September 2002. Within its programme of work, Technical Committee CEN/TC 133 requested CEN/TC 133/WG 5 “Copper for electrical purpose
26、s“ to prepare the following standard: EN 13599, Copper and copper alloys Copper plate, sheet and strip for electrical purposes. The products specified in this European Standard are those which are especially suitable for electrical purposes, i.e. with specified electrical properties. Copper plate, s
27、heet and strip for general purposes are specified in EN 1652. Annex A (informative) gives guidance on the characteristics of coppers for electrical purposes. This is one of a series of European Standards for copper products for electrical purposes. Other copper products are specified as follows: EN
28、13600, Copper and copper alloys Seamless copper tubes for electrical purposes. EN 13601, Copper and copper alloys Copper rod, bar and wire for general electrical purposes. EN 13602, Copper and copper alloys Drawn, round copper wire for the manufacture of electrical conductors. EN 13604, Copper and c
29、opper alloys Products of high conductivity copper for electronic tubes, semiconductor devices and vacuum applications. EN 13605, Copper and copper alloys Copper profiles and profiled wire for electrical purposes. According to the CEN/CENELEC Internal Regulations, the national standards organizations
30、 of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. 3 Licensed Copy: sheffield
31、un sheffieldun, na, Sun Oct 29 10:12:51 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 13599:2002 (E) 1 Scope This European Standard specifies the composition, property requirements including electrical properties, and tolerances on dimensions and form for copper plate, sheet and strip for electrical
32、 purposes with thicknesses from 0,05 mm up to and including 25 mm and widths from 10 mm up to and including 1 250 mm. The sampling procedures, the methods of test for verification of conformity to the requirements of this standard, and the delivery conditions are also specified. 2 Normative referenc
33、es This European Standard incorporates, by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text, and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of thes
34、e publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references, the latest edition of the publication referred to applies (including amendments). EN 1655, Copper and copper alloys Declarations of conformity. EN 1976, Copper and copper all
35、oys Cast unwrought copper products. EN 10002-1, Metallic materials Tensile testing Part 1: Method of test (at ambient temperature). EN 10204, Metallic products Types of inspection documents. EN ISO 2626, Copper Hydrogen embrittlement test (ISO 2626:1973). EN ISO 6507-1, Metallic materials Vickers ha
36、rdness test Part 1: Test method (ISO 6507-1:1997). EN ISO 7438, Metallic materials Bend test (ISO 7438:1985). ISO 1811-2, Copper and copper alloys Selection and preparation of samples for chemical analysis Part 2: Sampling of wrought products and castings. NOTE Informative references to documents us
37、ed in the preparation of this standard, and cited at the appropriate places in the text, are listed in the bibliography. 3 Terms and definitions For the purposes of this European Standard, the following terms and definitions apply. 3.1 plate flat rolled product of rectangular cross-section with unif
38、orm thickness greater than 10 mm 3.2 sheet flat rolled product of rectangular cross-section with uniform thickness from 0,2 mm up to and including 10 mm, supplied in straight lengths, usually with sheared or sawn edges. The thickness does not exceed one tenth of the width 3.3 strip flat rolled produ
39、ct of rectangular cross-section with uniform thickness from 0,05 mm up to and including 5,0 mm manufactured in coil and supplied in as sheared coils, traverse wound coils or cut to length, usually with slit edges. The thickness does not exceed one tenth of the width 4 Licensed Copy: sheffieldun shef
40、fieldun, na, Sun Oct 29 10:12:51 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 13599:2002 (E) 4 Designations 4.1 Material 4.1.1 General The material is designated either by symbol or number (see Table 1). 4.1.2 Symbol The material symbol designation is based on the designation system given in ISO 11
41、90-1. NOTE Although material symbol designations used in this standard might be the same as those in other standards using the designation system in ISO 1190-1, the detailed composition requirements are not necessarily the same. 4.1.3 Number The material number designation is in accordance with the
42、system given in EN 1412. 4.2 Material condition For the purposes of this standard, the following designations, which are in accordance with the system given in EN 1173, apply for the material condition: MMaterial condition for the product as manufactured without specified mechanical properties; H. M
43、aterial condition designated by the minimum value of hardness requirement for the product with mandatory hardness requirements; R. Material condition designated by the minimum value of tensile strength requirement for the product with mandatory tensile strength and elongation requirements. NOTE Some
44、 R. material conditions in this standard apply to products which also have mandatory 0,2% proof strength requirements. Exact conversion between material conditions designated H. and R. is not possible. Material condition is designated by only one of the above designations. 4.3 Product The product de
45、signation provides a standardized pattern of designation from which a rapid and unequivocal description of a product is conveyed in communication. It provides mutual comprehension at the international level with regard to products which meet the requirements of the relevant European Standard. The pr
46、oduct designation is no substitute for the full content of the standard. 5 Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 10:12:51 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 13599:2002 (E) The product designation for products to this standard shall consist of: denomination (Plate, Sheet o
47、r Strip); number of this European Standard (EN 13599); material designation, either symbol or number (see Table 1); material condition designation (see Table 2); nominal dimensions; plate: thickness width length either “as manufactured“ (M) or “fixed“ (F) length; sheet: thickness width length either
48、 “as manufactured“ (M) or “fixed“ (F) length (see example 1); strip (in coils or on spools): thickness width (see example 2); strip (cut to length): thickness width length either “as manufactured“ (M) or “fixed“ (F) length. The derivation of a product designation is shown in example 1. EXAMPLE 1 She
49、et for electrical purposes conforming to this standard, in material designated either Cu-ETP or CW004A, in material condition H040, nominal thickness 6,0 mm, nominal width 600 mm, as manufactured length 2 000 mm, shall be designated as follows: EXAMPLE 2 Strip for electrical purposes conforming to this standard, in material designated either CuAg0,10 or CW013A, in material condition R290, nominal thickness 2,0 mm,