《BS-EN-12432-1998.pdf》由会员分享，可在线阅读，更多相关《BS-EN-12432-1998.pdf（8页珍藏版）》请在三一文库上搜索。
1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS EN 12432:1998 The Euro
2、pean Standard EN 12432:1998 has the status of a British Standard ICS 97.220.30 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Gymnastic equipment Balancing beams Functional and safety requirements, test methods Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 14:33:07 G
3、MT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 12432:1998 This British Standard, having been prepared under the direction of the Consumer Products and Services Sector Committee, was published under the authority of the Standards Committee and comes into effect on 15 December 1998 BSI 1998 ISBN 0 58
4、0 30357 8 Amendments issued since publication Amd. No.DateText affected National foreword This British Standard is the English language version of EN 12432:1998. The UK participation in its preparation was entrusted to Technical Committee SW/14, Gymnasium and sports equipment, which has the responsi
5、bility to: aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizati
6、ons represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled International Standards Cor
7、respondence Index, or by using the Find facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not
8、 of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 4, an inside back cover and a back cover. Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 14:33:07 GMT+00:00 2006, Uncontrolled Copy,
9、 (c) BSI CEN European Committee for Standardization Comite Europe en de Normalisation Europa isches Komitee fu r Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1998 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN
10、12432:1998 E EUROPEAN STANDARDEN 12432 NORME EUROPE ENNE EUROPA ISCHE NORM August 1998 ICS 97.220.30 Descriptors: sport equipment, gymnastic equipment, balancing beams, specifications, safety, dimensions, tests, mechanical tests, stability tests, stiffness tests, bend tests, instructions, marking En
11、glish version Gymnastic equipment Balancing beams Functional and safety requirements, test methods Mate riel de gymnastique Poutres Exigences fonctionelles et de se curite , me thodes dessai Turngera te Schwebebalken Funktionelle und sicherheitstechnische Anforderungen, Pru fverfahren This European
12、Standard was approved by CEN on 22 July 1998. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concernin
13、g such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own lang
14、uage and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden,
15、Switzerland and United Kingdom. Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 14:33:07 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Page 2 EN 12432:1998 BSI 1998 Foreword This European Standard has been prepared by Technical Committee CEN/TC 136, Sports, playground and other recreational equi
16、pment, the Secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by February 1999, and conflicting national standards shall be withdrawn at the latest by February 1999.
17、 This European Standard is one of several standards, each of which deals with a particular type or a particular group of gymnastic equipment. This European Standard should be read in conjunction with EN 913. According to the CEN/CENELEC Internal Regulations, the national standards organizations of t
18、he following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Contents Page Foreword2 1Scope3 2N
19、ormative references3 3Requirements3 4Safety requirements3 5Test methods3 6Instructions for use3 7Marking3 Annex A (informative) Typical examples of balancing beams4 Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 14:33:07 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Page 3 EN 12432:1998 BSI 199
20、8 1 Scope This standard specifies functional requirements (see clause 3) and specific safety requirements for free-standing balancing beams in addition to the general safety requirements in EN 913 (see clause 4). 2 Normative references This European Standard incorporates, by dated or undated referen
21、ce, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporate
22、d in it by amendment or revision. For undated references, the latest edition of the publication referred to applies. EN 913:1996, Gymnastic equipment General safety requirements and test methods. 3 Requirements 3.1 Height When measured from the top surface of the beam to the floor the maximum height
23、 of the beam in the installed position shall be not greater than 1 500 mm. Adjustable height balancing beams shall have a minimum adjustable range of 500 mm. 3.2 Deflection When tested in accordance with 5.1 the centre of the balancing beam shall not deflect by more than 10 mm and after removal of t
24、he test load shall return to its original position. 4 Safety requirements 4.1 General Balancing beams shall comply with the requirements of EN 913, except insofar as they are modified by this European Standard. 4.2 Stability When tested in accordance with 5.2.1 the balancing beam shall not move more
25、 than 5 mm sideways and the legs on the opposite side shall not lift from the floor by more than 1 mm. When tested in accordance with 5.2.2 the balancing beam shall not be pulled over. 4.3 Strength When tested in accordance with EN 913:1996, annex B, with the load applied in the centre of the balanc
26、ing beam, the equipment shall not collapse or fracture, or show any permanent deformation. 4.4 Legs of base The legs of the base shall not protrude beyond the end of the balancing beam. The base shall be not more than 60 mm above the floor level. 5 Test methods 5.1 Determination of deflection Place
27、the balancing beam in its in-use position at its maximum height. Measure the distance from the floor to the top surface of the balancing beam to the nearest 1 mm. Gently apply a force of 1 350 N in the middle of the balancing beam and measure the distance from the floor to the top surface of the bal
28、ancing beam to the nearest millimetre. Remove the force and remeasure the distance from the floor to the top surface of the balancing beam. Record the deflection under load and any residual deflection after removal of the load. 5.2 Determination of stability 5.2.1 Place the balancing beam in its in-
29、use position at its maximum height. Block the apparatus legs on one side to prevent sliding. Apply a force of 250 N sideways in the centre of the balancing beam perpendicular to the balancing beam and parallel to the floor towards the side of the apparatus with the blocking. Measure and record wheth
30、er the apparatus moves more than 5 mm sideways and whether the legs on the opposite side have lifted by more than 1 mm from the floor. 5.2.2 Using the arrangement described in 5.2.1 apply a force of 350 N. Record whether the apparatus falls over. 6 Instructions for use An information booklet shall b
31、e provided by the manufacturers containing the following: a) installation details; b) assembly details covering method of adjustment; c) equipment space; d) a warning that the base or any protruding part of the framework outside the profile of the beam should be protected by appropriate use of paddi
32、ng or mats, when in use; e) maintenance details; f) a warning notice that the equipment should be used under controlled supervision; g) a statement advising purchasers/installers/users that the colour of the beam should contrast with the floor and other nearby equipment (e.g. mats). 7 Marking Markin
33、g shall comply with EN 913. Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 14:33:07 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Page 4 EN 12432:1998 BSI 1998 Annex A (informative) Typical examples of balancing beams Dimensions in millimetres 1 2 3 4 5 6 Supports Base Beam Elastic material Sti
34、ff insert Padding Figure A.1 Typical examples Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 14:33:07 GMT+00:00 2006, Uncontrolled Copy, (c) BSI blank Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 14:33:07 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BSI 389 Chiswick High Road London
35、W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI i
36、s the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make su
37、re that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee respons
38、ible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, intern
39、ational and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise r
40、equested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and ser
41、vices. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. T
42、el: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, s
43、tored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or
44、grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070. Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 14:33:07 GMT+00:00 2006, Uncontrolled Copy, (c) BSI