《BS-A-354-2000 ISO-13596-2000.pdf》由会员分享，可在线阅读，更多相关《BS-A-354-2000 ISO-13596-2000.pdf（10页珍藏版）》请在三一文库上搜索。
1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD AEROSPACE SERIES BS A 354
2、:2000 ISO 13596:2000 ICS 49.030.30 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Inserts, self-locking, with MJ threads, closed type, in metallic material, coated or uncoated Dimensions Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 03:
3、39:52 GMT+00:00 2006, Uncontrolled Copy, (c) BSI This British Standard, having been prepared under the direction of the Engineering Sector Committee, was published under the authority of the Standards Committee and comes into effect on 15 April 2000 BSI 04-2000 ISBN 0 580 34616 1 BS A 354:2000 Amend
4、ments issued since publication Amd. No.DateComments National foreword This British Standard reproduces verbatim ISO 13596:2000 and implements it as the UK national standard. The UK participation in its preparation was entrusted by Technical Committee ACE/12, Aerospace fasteners and fastening systems
5、, to Subcommittee ACE/12/1, Aerospace fasteners and fastening systems (international), which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK inte
6、rests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications r
7、eferred to in this document may be found in the BSI Standards Catalogue under the section entitled International Standards Correspondence Index, or by using the Find facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a c
8、ontract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the ISO title page, pages ii and iii, a blan
9、k page, pages 1 to 3 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 03:39:52 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Reference number ISO 13596
10、:2000(E) INTERNATIONAL STANDARD ISO 13596 First edition 2000-03-01 Aerospace Inserts, self-locking, with MJ threads, closed type, in metallic material, coated or uncoated Dimensions Aronautique et espace Douilles filetes, freinage interne et filetage MJ, du type ferm, en matriau mtallique, revtues o
11、u non revtues Dimensions BS A 354:2000 Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 03:39:52 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ii? BS A 354:2000 Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 03:39:52 GMT+00:00
12、2006, Uncontrolled Copy, (c) BSI ?iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body
13、 interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotec
14、hnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publ
15、ication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of patent rights. ISO shall not be held responsible for identifying any or al
16、l such patent rights. International Standard ISO 13596 was prepared by Technical Committee ISO/TC 20,Aircraft and space vehicles, Subcommittee SC 4,Aerospace fastener systems. BS A 354:2000 Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 03:39:52 GMT+00:00 2006,
17、 Uncontrolled Copy, (c) BSI BS A 354:2000 Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 03:39:52 GMT+00:00 2006, Uncontrolled Copy, (c) BSI INTERNATIONAL STANDADR?ISO 69531:(0002)E ?1 Aerospace Inserts, self-locking, with MJ threads, closed type, in metallic m
18、aterial, coated or uncoated Dimensions 1?Scope This International Standard specifies the dimensions of closed inserts, with self-locking MJ threads, in metallic material, coated or uncoated, for honeycomb and composite materials. The classification referring to strength and temperature, depending on
19、 the core material and potting compound, is not specified. This International Standard is only applicable to the compilation of aerospace product standards. 2?Normative reference The following normative document contains provisions which, through reference in this text, constitute provisions of this
20、 International Standard. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent edition of the normative doc
21、ument indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards. ISO 5855-2:1999,Aerospace MJ threads Part 2: Limit dimensions for bolts and nuts. 3?Configuration and
22、 dimensions See Figure 1 and Table 1. Dimensions and tolerances are expressed in millimetres. They apply to inserts after any surface coating(s). BS A 354:2000 Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 03:39:52 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 2?
23、 Details of form not stated are at the manufacturers discretion. Key 1?Thread 2?Pitch diameter 3?Shank deformed this area to provide thread lock 4?Antirotation feature at manufacturers option on shank or bottom flange 5?Potting and vent hole a These values, in micrometres, are valid prior to any sur
24、face coating(s). The values do not apply to threads having a surface texture obtained by usual manufacturing methods. Figure 1 BS A 354:2000 Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 03:39:52 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ?3 Table 1 ABCDEbF Di
25、ameter code Thread a ? 0,25? 0,25 0 ? 0,25?min.?nom.?tol. 030?MJ3 ? 0,5-4H6H?36 040?MJ4 ? 0,7-4H6H?48 9 or 12 or 15 or 19 or 22 or 25 050?MJ5 ? 0,8-4H6H 14,2?9,3 510 12 or 15 or 19 or 22 or 25 060?MJ6 ? 1-4H5H?17,5?11,9 2,4 612 15 or 19 or 22 or 25 ?0,25 a In accordance with ISO 5855-2 b Effective l
26、ength of a bolt thread engagement 4?Example of application See Figure 2. Key 1?Washer 2Bolt 3?Potting compound 4?Attached component 5?Sandwich panel 6?Insert Figure 2 BS A 354:2000 Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 03:39:52 GMT+00:00 2006, Uncontro
27、lled Copy, (c) BSI BS A 354:2000 ISO 13596:2000 BSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
28、 | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standar
29、ds are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using t
30、his British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically rec
31、eive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI impleme
32、ntation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic info
33、rmation services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of stand
34、ards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted
35、 under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of i
36、mplementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070. Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 03:39:52 GMT+00:00 2006, Uncontrolled Copy, (c) BSI