《BS-EN-15380-3-2006.pdf》由会员分享，可在线阅读，更多相关《BS-EN-15380-3-2006.pdf（16页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 15380-3:2006 Railway applications Designation system for railway vehicles Part 3: Designation of installation sites and locations The European Standard EN 15380-3:2006 has the status of a British Standard ICS 01 110; 45.060.01 ? BS EN 15380-3:2006 This British Standard was pub
2、lished under the authority of the Standards Policy and Strategy Committee on 31 July 2006 BSI 2006 ISBN 0 580 48946 9 National foreword This British Standard is the official English language version of EN 15380-3:2006. The UK participation in its preparation was entrusted to Technical Committee RAE/
3、1, Railway applications, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary. This standard has been produced from Part 4 of the DIN 25002 series of standards under the CEN fast-track procedure. The UK voted against the d
4、ocument in both associated ballots stating that the translation of the documents from German to prepare the English version has resulted in a lack of clarity as to the intent and meaning of some of the terminology used. There is a concern that some of the railway-related terminology used does not co
5、rrespond to UK usage. Therefore, this standard should be applied with care and consideration in order to avoid misunderstanding. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the sect
6、ion entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. C
7、ompliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep UK interests informed; monitor related
8、 international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 12, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the docum
9、ent was last issued. Amendments issued since publication Amd. No. DateComments EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 15380-3 April 2006 ICS 01.110; 45.060.01 English Version Railway applications - Designation system for railway vehicles - Part 3: Designation of installation sites and
10、locations Applications ferroviaires - Systme de classification pour vhicules ferroviaires - Partie 3: Description des positions dinstallation Bahnanwendungen - Kennzeichnungssystematik fr Schienenfahrzeuge - Teil 3: Kennzeichnung von Aufstellungs- und Einbauorten This European Standard was approved
11、by CEN on 6 March 2006. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standa
12、rds may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to t
13、he Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Nor
14、way, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2006 CENAll rights of exploitation in any for
15、m and by any means reserved worldwide for CEN national Members. Ref. No. EN 15380-3:2006: E EN 15380-3:2006 (E) 2 Contents Page Foreword3 Introduction.4 1 Scope 4 2 Normative references4 3 Terms and definitions .4 4 Designation of installation sites.4 4.1 General4 4.2 Designation set5 5 Designation
16、of locations.6 5.1 General6 5.2 Designation set6 Annex A (informative) Examples of installation site and location designation9 Bibliography12 List of Tables Table 1 Location subdivision. 8 List of Figures Figure 1 Designation principle. 5 Figure 2 Example of installation site vehicle designation 5 F
17、igure 3 Location designation principle. 6 Figure 4 Example of a location designation. 7 Figure 5 Example of a location designation with product group and location given 7 Figure A.1 Examples of installation site and location designation . 9 Figure A.2 Designation of locations on a locomotive. 10 Fig
18、ure A.3 Designation of locations on a 3-compartment suburban vehicle . 11 EN 15380-3:2006 (E) 3 Foreword This document (EN 15380-3:2006) has been prepared by Technical Committee CEN/TC 256 “Railway applications”, the secretariat of which is held by DIN. This European Standard shall be given the stat
19、us of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2006, and conflicting national standards shall be withdrawn at the latest by October 2006. The EN 15380 series of standards, Railway applications Designation system for railway vehicles
20、consists of: Part 1: General principles Part 2: Product groups Part 3: Designation of installation sites and locations This European Standard is based on Part 4 of the DIN 25002 series of standards. After approval, the text of DIN 25002-4 submitted to the PQ procedure was brought into line with the
21、formal requirements of an EN. The resulting editorial amendments have led to slightly modified wordings but they have no effect on the technical content of this document. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to i
22、mplement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and th
23、e United Kingdom. EN 15380-3:2006 (E) 4 Introduction Giving the location designations is necessary in order to systematize installation planning and to provide traceability of vehicle parts, structural units, combined assemblies and objects. 1 Scope As a railway-specific technical standard, this doc
24、ument gives rules for the designation of installation sites and locations in railway vehicles. 2 Normative references The following referenced documents are indispensable for the application of this European Standard. For dated references, only the edition cited applies. For undated references, the
25、latest edition of the referenced document (including any amendments) applies. EN 15380-1:2006, Railway aplications Designation system for railway vehicles Part 1: General principles EN 15380-2, Railway aplications Designation system for railway vehicles Part 2: Product groups 3 Terms and definitions
26、 For the purposes of this document, the terms given in EN 15380-1:2006 apply. 4 Designation of installation sites 4.1 General This designation gives information concerning the position of a unit, a vehicle or an assembly in a fixed train configuration. EN 15380-3:2006 (E) 5 4.2 Designation set Figur
27、e 1 shows the layout of the designation set. It consists of the prefix signs ”+” followed by three code letters and two code numbers for the position inside a fixed train configuration. Key 1 Installation site prefix sign 2 Designation of railway vehicles 3 Designation of train (vehicle fleet) 4 Des
28、ignation of vehicle type 5 Position within the train (only required if identical vehicles exist within a train) Figure 1 Designation principle Examples of the data positions A1, A2 and A3 are given in Annex A of EN 15380-1:2006. Figure 2 shows an example of a designation of one of several identical
29、vehicles in a train configuration as indicated in Figure A.1. Key 1 Installation site prefix sign 2 “Rolling Stock“ vehicle fleet 3 High-speed train 4 Centre car (vehicle type) 5 Vehicle No.02 in the train Figure 2 Example of installation site vehicle designation EN 15380-3:2006 (E) 6 Annex A gives
30、examples of the numbering system of installation sites and locations. 5 Designation of locations 5.1 General This designation gives information concerning the location of structural units, combined assemblies and objects in vehicles, structural units and assemblies. 5.2 Designation set Figure 3 show
31、s the layout of the designation set. It consists of the prefix sign “+“ followed by two code letters for the product group, two code numbers (location), a classification mark and a further possibility for designating the location. It is not required in every case to indicate the product group. Examp
32、les are shown in Figures 4 and 5. Key 1 Location prefix sign 2 Product group plan according to EN 15380-2 3 Subdivision of the locations in a vehicle (see Table 1) 4 Designation of the locations in combined assemblies, structural units and objects (areas and/or co-ordinates) not specified Figure 3 L
33、ocation designation principle Figure 4 shows an example of the minimum entry for a location designation EN 15380-3:2006 (E) 7 Key 1 Location prefix sign 2 Pantograph 3 Location on the roof (see Table 1) 4 Location Figure 4 Example of a location designation Figure 5 shows an example of a complete loc
34、ation designation. Key 1 Location prefix sign 2 Runnig gear from EN 15380-2 3 Underframe location (see Table 1) 4 Location in running gear (W1L = wheelset shaft 1 left-hand side) Figure 5 Example of a location designation with product group and location given The corresponding numbers for designatin
35、g the locations are specified in Table 1. The figures in the Annex are intended to clarify matters for different railway vehicles. EN 15380-3:2006 (E) 8 Table 1 Location subdivision Main group Subdivision Name of the location 00 Roof, outside 01 to 09 Roof, outside; subdivision according to the situ
36、ation 10 Drivers cab 11 Drivers desk 12 Cubicle in the drivers cab, left-hand side 13 Cubicle in the drivers cab, right-hand side 10 14 Drivers cab, rear wall, left-hand side 15 Drivers cab, rear wall, right-hand side 16 Drivers cab, floor 17 Drivers cab, ceiling 18 Vehicle head, left-hand side 19 V
37、ehicle head, right-hand side 20 Side wall, right-hand side (with cove) 21 to 29 Subdivision according to the situation (e.g. windows) 30 Side wall, left-hand side (with cove) 31 to 39 Subdivision according to the situation 40 Interior, right-hand side 41 to 49 Subdivision according to the situation
38、50 Interior, left-hand side 51 to 59 Subdivision according to the situation 60 Interior ceiling 61 to 69 Subdivision according to the situation, e.g. intermediate ceiling in double-decker coaches 70 Underframe (framework of a locomotive) 71 to 79 Subdivision according to the situation 80 End wall, r
39、ear wall, intercommunication gangway, drivers cab 2 of single-unit vehicles (e.g. in locomotives) 81 to 89 Subdivision according to the situation 90 Reserved EN 15380-3:2006 (E) 9 Annex A (informative) Examples of installation site and location designation Figure A.1 shows the designation of the ins
40、tallation site and location in various trains. The direction of travel of the vehicles is shown in acordance with EN 13775-1. Key 1 Locomotive, 2 drivers cabs 2 Traction unit head, 1 drivers cab 3 Traction unit, 2 drivers cabs 4 Traction unit, 4-compartment 5 Suburban train, underground train 6 High
41、-speed train (ICT) Direction of counting Figure A.1 Examples of installation site and location designation Other examples of installation site and location designation are given in Figures A.2 and A.3. EN 15380-3:2006 (E) 10 Figure A.2 Designation of locations on a locomotive EN 15380-3:2006 (E) 11
42、Figure A.3 Designation of locations on a 3-compartment suburban vehicle EN 15380-3:2006 (E) 12 Bibliography 1 EN 13775-1, Railway aplications Measuring of new and modified freight wagons - Part 1: Measuring principles blank BS EN 15380-3:2006 BSI 389 Chiswick High Road London W4 4AL BSI British Stan
43、dards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British S
44、tandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the tech
45、nical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying s
46、tandards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international
47、standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical H
48、elp to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-. Subscribing members of BSI are kept up to date with stand
49、ards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-. Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- Furthe