《BS-EN-12560-7-2004.pdf》由会员分享，可在线阅读，更多相关《BS-EN-12560-7-2004.pdf（22页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 12560-7:2004 Flanges and their joints Gaskets for Class-designated flanges Part 7: Covered metal jacketed gaskets for use with steel flanges The European Standard EN 12560-7:2004 has the status of a British Standard ICS 23.040.80 ? Licensed Copy: sheffieldun sheffieldun, na, S
2、at Oct 28 07:00:39 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 12560-7:2004 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 14 June 2004 BSI 14 June 2004 ISBN 0 580 43936 4 National foreword This British Standard is the official English
3、language version of EN 12560-7:2004 The UK participation in its preparation was entrusted to Technical Committee PSE/2, Jointing materials and compounds, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary. Cross-referenc
4、es The British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British St
5、andards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to t
6、he responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside f
7、ront cover, the EN title page, pages 2 to 18, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. DateComments Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 07:00
8、:39 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 12560-7 June 2004 ICS 23.040.80 English version Flanges and their joints - Gaskets for Class-designated flanges - Part 7: Covered metal jacketed gaskets for use with steel flanges Brides et leurs asse
9、mblages - Joints pour les brides dsignes Class - Partie 7: Joints mtalloplastiques revtus pour utilisation avec des brides en acier Flansche und ihre Verbindungen - Dichtungen fr Flansche mit Class-Bezeichnung - Teil 7: Metallummantelte Dichtungen mit Auflage fr Stahlflansche This European Standard
10、was approved by CEN on 1 April 2004. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such na
11、tional standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and
12、notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Net
13、herlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2004 CENAll rights of exploitation in any
14、 form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12560-7:2004: E Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 07:00:39 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 12560-7:2004 (E) 2 Contents page Foreword3 1 Scope 4 2 Normative references4 3 Terms and defin
15、itions .4 4 Designations 4 4.1 Range of Class designations4 4.2 Range of gasket sizes .5 4.3 Gasket types.5 4.4 Information to be supplied by the purchaser .5 5 Constructional details.5 5.1 General details.5 5.2 Metal jacket.7 5.2.1 Metal jacket description7 5.2.2 Metal jacket material7 5.3 Soft fil
16、ler .7 5.3.1 Soft filler description.7 5.3.2 Soft filler material.7 5.4 Covering layers8 5.4.1 Covering layers description .8 5.4.2 Covering layers material.8 5.5 Inner and outer rings.8 5.5.1 Inner and outer rings description 8 5.5.2 Inner and outer rings material9 5.6 Attachment of facing.9 5.6.1
17、Methods of attachment .9 5.6.2 De-greasing of core.9 5.6.3 Number of joins9 5.6.4 Excessive facing9 5.7 Integrity of facing attachment 9 5.8 Construction characteristics details9 6 Dimenisons.10 7 Marking.12 8 Colour coding.13 9 Packaging.13 Annex A (informative) Information to be supplied by the pu
18、rchaser15 Annex B (informative) A-deviation16 Bibliography18 Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 07:00:39 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 12560-7:2004 (E) 3 Foreword This document (EN 12560-7:2004) has been prepared by Technical Committee CEN/TC 74 “Flanges and their
19、 joints”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2004, and conflicting national standards shall be withdrawn at the latest by December 20
20、04. The annex A is informative and contains “Information to be supplied by the purchaser“. The annex B is informative and contains “A-deviations“. EN 12560 consists of 7 parts: Part 1: Non-metallic flat gaskets with or without inserts Part 2: Spiral wound gaskets for use with steel flanges Part 3: N
21、on-metallic PTFE envelope gaskets Part 4: Corrugated, flat or grooved metallic and filled metallic gaskets for use with steel flanges Part 5: Metallic ring joint gaskets for use with steel flanges Part 6: Covered serrated metal gaskets for use with steel flanges Part 7: Covered metal jacketed gasket
22、s for use with steel flanges According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Icelan
23、d, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 07:00:39 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 12560-7:2004 (E) 4 1 Scope
24、This European Standard specifies the construction, dimensions and marking of covered metal jacketed gaskets for use with flanges complying with prEN 1759-1 for Class 150, Class 300, Class 600, Class 900. Class 1 500 for sizes up to and including NPS 24, and for Class designation 2 500 up to and incl
25、uding NPS 12. This European Standard does not extend to covered metal jacketed based heat exchanger gaskets with pass bars or large vessel gaskets but, in the lack of a dedicated document for such gaskets, the principles set down may be applied to them. NOTE 1 Dimensions of other types of gaskets fo
26、r use with flanges to prEN 1759-1, EN 1759-3 and EN 1759-4 are given in EN 12560-1, EN 12560-2, EN 12560-3, EN 12560-4, EN 12560-5 and EN 12560-6. NOTE 2 Annex A lists information that should be supplied by the purchaser when ordering gaskets in circumstances where the choice of the gasket materials
27、 appropriate to the service is left to the supplier. 2 Normative references Not applicable. 3 Terms and definitions For the purposes of this European Standard, the following terms and definitions apply. 3.1 covered metal jacketed gasket consists of a sealing element with or without a location ring w
28、hich may not be rigidly fixed to the sealing element NOTE The sealing element consists of a metal jacketed core and a conformable sealing material adhered both top and lower metal jacketed core surfaces. 3.2 DN see EN ISO 6708 3.3 NPS see EN 1759-3 3.4 Class see EN 1759-3 4 Designations 4.1 Range of
29、 Class designations Gaskets shall be designated as suitable for use with one or more of the following Class designations of flange: Class 150, Class 300, Class 600, Class 900, Class 1 500 and Class 2 500. Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 07:00:39 GMT+00:00 2006, Uncontrolled Co
30、py, (c) BSI EN 12560-7:2004 (E) 5 4.2 Range of gasket sizes Gasket nominal sizes shall also be designated in accordance with the ranges specified in Tables 2 and 3. The general principles described in this standard shall be applied to gaskets outside of the ranges specified in Tables 2 and 3 by agre
31、ement between supplier and customer. 4.3 Gasket types Gasket types, as illustrated in Figure 1, shall be designated as: Type SC: Sealing element self centring (used with type C/D or E/F flange facings); Type C/I: Sealing element with inner ring (used with type C/D or E/F flange facings); Type C/O: S
32、ealing element with centring ring (used with type A or B flange facings); Type C/IO: Sealing element with centring ring and inner ring (used with type A or B flange facings). The type A, type B, type C/D, type E/F flange facings are specified in prEN 1759-1. 4.4 Information to be supplied by the pur
33、chaser The selection of gasket materials and type should take into account the fluid, the operating conditions and the properties of the gasket materials as well as the type of flange. It is recommended that the selection of a gasket for any particular application is made in consultation with the ga
34、sket supplier who will advise on the materials required for a particular service (see annex A). 5 Constructional details 5.1 General details The covered metal jacketed gasket shall consist of a metal jacketed core and of covering layers stuck on both sides. All gasket sizes and classes shall be desi
35、gned so that an applied uniform bolt stress of 200 MPa will correctly seat the gasket and offer the required level of seal. Gaskets for which dimensions are specified shall be one of the designs shown in Figure 1. Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 07:00:39 GMT+00:00 2006, Uncont
36、rolled Copy, (c) BSI EN 12560-7:2004 (E) 6 a) Type SC b) Type C/I c) Type C/O d) Type C/IO Figure 1 Covered metal jacketed gaskets a) gaskets (C/O or C/IO type) for use with type A (flat face) or type B (raised face) flanges b) gaskets (SC or C/I type) for use with type C/D (tongue/groove) or type E
37、/F (spigot/recess) flanges Key 1 Centring ring 2 Sealing element 3 Inner ring Figure 2 Examples of typical covered metal jacketed gaskets configurations Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 07:00:39 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 12560-7:2004 (E) 7 5.2 Metal jacket 5
38、.2.1 Metal jacket description The tolerance of the inside and the outside diameters of metal jacket cross section are given in Tables 2 and 3. Thickness of the metal jacket cross section is depending on the soft filler material. 5.2.2 Metal jacket material The material of the shell of the metal jack
39、et shall be selected to be compatible with the intended service. Table 4 lists the most frequently used materials. The shell of the metal jacket shall have a thickness between 0,3 mm and 0,5 mm. 5.3 Soft filler 5.3.1 Soft filler description The thickness of the soft filler material shall be selected
40、 to ensure: a good compressibility and elastic recovery of the gasket in order to compensate as much as possible the flatness defaults and to respond to variations due to operating conditions; a final thickness (with covering layers) adapted with the length of the piping line (after tightening); the
41、 compatibility with the assembly specification (spigot and recess or tongue and groove, metal to metal contact, .). 5.3.2 Soft filler material The filler material shall be selected in accordance with the intended service but as guidance, satisfactory mechanical behaviour is usually obtained with the
42、 following soft filler materials: Suitable expanded graphite is: 98 % purity, ash content max. 2 %, sulphur content max. 1 000 10-6 (ppm), halogen contents max. 50 10-6 (ppm), the initial density shall be 1,0 g/cm3 to 1,1 g/cm3. Suitable expanded PTFE is: Not recycled 100 % expanded PTFE, the initia
43、l density shall be 0,7 g/cm3 to 0,9 g/cm3. Suitable Flexible Mica is: Phlogopite Mica (content 96 %) with Silicon binder, the initial density shall be 1,8 g/cm3 to 1,9 g/cm3. Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 07:00:39 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 12560-7:2004 (E
44、) 8 5.4 Covering layers 5.4.1 Covering layers description The covering layers material and thickness should be selected to be compatible: with the process fluid, and the operating conditions; the type and surface finish of the flange facings; the flange bolt loading; and to guarantee: satisfactory l
45、evel of seal; a good adaptation with flange facings defaults. 5.4.2 Covering layers material As a guidance, satisfactory leaktightness is usually reached with the following covering materials: Suitable expanded graphite is: 98 % purity, ash content max. 2 %, sulphur content max. 1 000 10-6 (ppm), ha
46、logen contents max. 50 10-6 (ppm), the initial density shall be 1,0 g/cm3 to 1,1 g/cm3. to be finished with an anti-sticking coating Suitable Virgin PTFE is: not recycled 100 % PTFE, the initial density shall be 1,6 g/cm3. Suitable Expanded Vermiculite is: the initial density shall be 1,2 g/cm3. NOT
47、E It would be preferable that the gasket does not show any adhesion to the flange facings. 5.5 Inner and outer rings 5.5.1 Inner and outer rings description The ring thickness depend on the sealing element thickness. The rings material and thickness should be selected to be compatible: with the asse
48、mbly considered (spigot and recess or tongue and groove, metal to metal contact, .), with the process fluid, and the operating conditions, Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 07:00:39 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 12560-7:2004 (E) 9 and to guarantee: protection of
49、the sealing element against over-load sufficient load to assure good level of seal. The tolerances of the inside and outside diameters of the inner and/or outer rings are given in tables 2 and 3. 5.5.2 Inner and outer rings material For the outer ring, carbon steel may be selected as standard. For the inner ring, the same material or one with better corrosion resistance than that of the metal jacket shall be selected as standard. 5.6 Attac