《BS-EN-12346-1999.pdf》由会员分享，可在线阅读，更多相关《BS-EN-12346-1999.pdf（12页珍藏版）》请在三一文库上搜索。
1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS EN 12346:1999 The Euro
2、pean Standard EN 12346:1998 has the status of a British Standard ICS 97.220.30 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Gymnastic equipment Wall bars, lattice ladders and climbing frames Safety requirements and test methods Licensed Copy: sheffieldun sheffieldun, na, Sa
3、t Oct 28 16:50:51 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 12346:1999 This British Standard, having been prepared under the direction of the Consumer Products and Services Sector Committee, was published under the authority of the Standards Committee and comes into effect on 15 February 1999
4、 BSI 02-1999 ISBN 0 580 30090 0 Amendments issued since publication Amd. No.DateText affected National foreword This British Standard is the English language version of EN 12346:1998. The UK participation in its preparation was entrusted to Technical Committee SW/14, Gymnasium and sports equipment,
5、which has the responsibility to: aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK
6、. A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled Inter
7、national Standards Correspondence Index, or by using the Find facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a Bri
8、tish Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 9 and a back cover. Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 16:50:51 GMT+00:00 2006, Uncontrolled Copy,
9、 (c) BSI CEN European Committee for Standardization Comite Europe en de Normalisation Europa isches Komitee fu r Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1998 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN
10、12346:1998 E EUROPEAN STANDARDEN 12346 NORME EUROPE ENNE EUROPA ISCHE NORM June 1998 ICS 97.220.30 Descriptors: sports equipment, gymnastic equipment, safety, accident prevention, specifications, dimensions, mechanical strength, tests, marking English version Gymnastic equipment Wall bars, lattice l
11、adders and climbing frames Safety requirements and test methods Mate riel de gymnastique Espaliers, e chelles et cadres a grimper Prescriptions de se curite et me thodes dessai Turngera te Sprossenwa nde, Gitterleitern und Kletterrahmen Sicherheitstechnische Anforderungen und Pru fverfahren This Eur
12、opean Standard was approved by CEN on 6 June 1998. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references conc
13、erning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own
14、 language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Swe
15、den, Switzerland and United Kingdom. Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 16:50:51 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Page 2 EN 12346:1998 BSI 02-1999 Foreword This European Standard has been prepared by Technical Committee CEN/TC 136, Sports, playground and other recreatio
16、nal equipment, the Secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 1998, and conflicting national standards shall be withdrawn at the latest by Decemb
17、er 1998. This European Standard is one of a package, each of which deals with a particular type or a particular group of equipment. This European Standard should be read in conjunction with EN 913. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the followi
18、ng countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Contents Page Foreword2 1Scope3 2Normative r
19、eferences3 3Profile of bars3 4Safety requirements3 5Test methods3 6Instructions for use3 7Marking3 Annex A (informative) Typical examples of wall bars, lattice ladders and climbing frames6 Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 16:50:51 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Page
20、 3 EN 12346:1998 BSI 02-1999 1 Scope This European Standard specifies specific safety requirements for wall bars, lattice ladders and climbing frames, which are additional to the general safety requirements in EN 913. 2 Normative references This European Standard incorporates, by dated or undated re
21、ference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorp
22、orated in it by amendment or revision. For undated references, the latest edition of the publication referred to applies. EN 913, Gymnastic equipment General safety requirements and test methods. 3 Profile of bars All bars shall comply with the dimensions specified in Figure 1. Any profile lying bet
23、ween the dimensions shown is acceptable. Dimensions in millimetres Figure 1 Profile of bar 4 Safety requirements 4.1 General requirements Wall bars, lattice ladders and climbing frames shall comply with the requirements of EN 913, except insofar as they are modified by this European Standard. Typica
24、l examples are shown in Figures A.1 to A.4. 4.2 Strength 4.2.1 Pre-installation with the equipment assembled for bars, joints and supports 4.2.1.1 When tested in accordance with 5.1.1, the bar, joint and supports shall show no signs of loose bonds, cracking, breaking or permanent deformation. 4.2.1.
25、2 When tested in accordance with 5.1.2, the bar shall show no signs of rotation. 4.2.2 Post-installation strength When tested in accordance with 5.2, the equipment shall not pull away from the wall. 4.3 Supports For wall bars, the distance between supports shall be not less than 800 mm. For lattice
26、ladders and climbing frames, the distance between supports shall be not less than 500 mm. 4.4 Height For wall bars, the highest bar shall be not more than 3 000 mm above the ground. For lattice ladders and climbing frames, the highest bar shall be not more than 5 000 mm above the ground. 5 Test meth
27、ods 5.1 Pre-installation with the equipment assembled for bars, joints and supports 5.1.1 Apply a force of 1 700 N50 N in the middle of a bar, perpendicular to the face of the apparatus, for 5 min10 s; see Figure 2. Remove the force and examine the bar, joint and supports for signs of loose bonds, c
28、racking or permanent deformation. 5.1.2 Apply a torque of 50 Nm2 Nm to a bar for 5 min10 s. Remove the torque and examine the bar for signs of rotation. 5.2 Post-installation strength After installation according to the manufacturers instructions and with the equipment in its intended position of us
29、e, apply a force F1, centrally to the top bar, perpendicular and away from the wall, of 900 N for 5 min10 s; see Figure 3. Remove the force and determine whether the equipment has pulled away from the wall. Repeat the test with a force F2of 900 N for 5 min10 s on the lowest bar. 6 Instructions for u
30、se For retractable equipment, assembly instructions shall be provided. 7 Marking Marking shall comply with EN 913, and in addition shall include the following: a) name of product; and b) a statement advising the maximum number of users (maximum safe load). Licensed Copy: sheffieldun sheffieldun, na,
31、 Sat Oct 28 16:50:51 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Page 4 EN 12346:1998 BSI 02-1999 Figure 2 Determination of pre-installation strength Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 16:50:51 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Page 5 EN 12346:1998 BSI 02-1999 Figure 3 De
32、termination of post-installation strength Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 16:50:51 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Page 6 EN 12346:1998 BSI 02-1999 Annex A (informative) Typical examples of wall bars, lattice ladders and climbing frames Dimensions in millimetres Fig
33、ure A.1 Example of a wall bar Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 16:50:51 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Page 7 EN 12346:1998 BSI 02-1999 Dimensions in millimetres 1Crossbar4Floor plate 2Rung5Cantilever bracket 3Upright Figure A.2 Example of a lattice ladder Licensed
34、Copy: sheffieldun sheffieldun, na, Sat Oct 28 16:50:51 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Page 8 EN 12346:1998 BSI 02-1999 Dimensions in millimetres 1Bars 2Uprights Figure A.3 Example of multi-section wall bar Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 16:50:51 GMT+00:00 2006, Un
35、controlled Copy, (c) BSI Page 9 EN 12346:1998 BSI 02-1999 Figure A.4 Example of a climbing frame Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 16:50:51 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | |
36、 | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body responsible for preparing Brit
37、ish Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is
38、the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front c
39、over. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed
40、 to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range o
41、f information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax
42、: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright sub
43、sists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by a
44、ny means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any ot
45、her purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070. Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 16:50:51 GMT+00:00 2006, Uncontrolled Copy, (c) BSI