《BS-EN-1271-2004.pdf》由会员分享，可在线阅读，更多相关《BS-EN-1271-2004.pdf（16页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 1271:2004 Incorporating Corrigendum No. 1 Playing field equipment Volleyball equipment Functional and safety requirements, test methods The European Standard EN 1271:2004 has the status of a British Standard ICS 97.220.30; 97.220.40 ? Licensed Copy: sheffieldun sheffieldun, na
2、, Sat Oct 28 14:40:52 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 1271:2004 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 November 2004 BSI June 2006 ISBN 0 580 44914 9 National foreword This British Standardis the official Englishl
3、anguage version ofEN 1271:2004, including Corrigendum October 2005. It supersedes BS EN 1271:1998 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee SW/14, Gymnasium and sports equipment, which has the responsibility to: A list of organizations represent
4、ed on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “ International Standards Correspondence Index” ,
5、or by using the “ Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer
6、immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate
7、them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 12, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publication
8、 Amd. No. 16263 June 2006 Modifying 4.2, 4.3, 5.2 and 5.3 Corrigendum No. 1 DateComments Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 14:40:52 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1271 September 2004 ICSSupersedes EN 1271:1998 Engl
9、ish version Playing field equipment - Volleyball equipment - Functional and safety requirements, test methods Equipements de jeux - Equipements de volley-ball - Exigences fonctionnelles et de scurit, mthodes dessai Spielfeldgerte - Volleyballgerte - Funktionelle und sicherheitstechnische Anforderung
10、en, Prfverfahren This European Standard was approved by CEN on 24 June 2004. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibli
11、ographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of
12、 a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, L
13、atvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2
14、004 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1271:2004: E Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 14:40:52 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 1271:2004 (E) 2 ContentsPage Foreword3 1 Scope 4 2 Normat
15、ive references4 3 Requirements.4 3.1 Classification4 3.2 Dimensions.4 3.3 Material .7 3.3.1 Posts .7 3.3.2 Net 7 3.3.3 Antenna.7 3.4 Design.7 3.4.1 Posts .7 3.4.2 Net 7 3.4.3 Antennas.8 3.4.4 Ground sockets8 4 Safety requirements 8 4.1 General8 4.2 Posts .9 4.3Tensioning devices and rope attachment.
16、9 4.4Post pads (Classes A and B)9 4.5 Base assembly.9 5 Test methods9 5.1 General9 5.2Testing of posts and tensioning device9 6Instructions for use .10 7Marking.10 Annex A (informative) Example of foundation .11 Bibliography12 5.3Test of tensioning device.10 Licensed Copy: sheffieldun sheffieldun, n
17、a, Sat Oct 28 14:40:52 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 1271:2004 (E) 3 Foreword This document (EN 1271:2004) has been prepared by Technical Committee CEN/TC 136 “ Sport, playground and other recreational equipment” , the secretariat of which is held by DIN. This European Standard shall
18、 be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March 2005, and conflicting national standards shall be withdrawn at the latest by March 2005. This document supersedes EN 1271:1998. According to the CEN/CENELEC Internal Regu
19、lations, the national standards organizations of the following coun- tries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Esto- nia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Ne- therla
20、nds, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 14:40:52 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 1271:2004 (E) 4 1 Scope This document specifies the functional requirements (see Clause 3) a
21、nd the safety requirements (see Clause 4) for volleyball equipment. This document is applicable to 2 types and 3 classes of volleyball equipment (see 3.1) which are used indoors and outdoors. This document is not applicable to beach volleyball. 2 Normative references The following referenced documen
22、ts are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 913:1996, Gymnastic equipment General safety requirements and test methods EN
23、ISO 1806, Fishing nets Determination of mesh breaking force of netting (ISO 1806:2002) prEN ISO 2307, Fibre ropes Determination of certain physical and mechanical properties (ISO/DIS 2307:2003) EN ISO 13934-1, Textiles Tensile properties of fabrics Part 1: Determination of maximum force and elonga-
24、tion at maximum force using the strip method (ISO 13934-1:1999) ISO 3108, Steel wire ropes for general purposes Determination of actual breaking load 3 Requirements 3.1 Classification Volleyball equipment shall be classified by the design (types) and the intended level of the sport (classes) as show
25、n in Tables 1 and 2. Table 1 Types Type Description Example 1 with ground sockets/fixings Figure 1 2 with floor fixings Figure 2 Table 2 Classes Class Description AInternational competitionsa B national competitionsb C practice and school sports a in line with the FIVB (Fdration Internationale de Vo
26、lleyball) rules b in line with the rules of the national volleyball federations 3.2 Dimensions Volleyball equipment Classes A and B shall comply with the dimensions shown in Figure 1. Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 14:40:52 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 1271:2
27、004 (E) 5 Dimensions in millimetres Key 1 post 2 net 3 upper edge band 4 lower edge band 5 top net line 6 tension ropes 7 tension rope (optional) 8 edge reinforcement 9 side band 10 antenna pocket (alternative to 9) 11 antenna 12 sport surface 13 court line 14 ground socket For example of foundation
28、s see Annex A. NOTE The height of the net is specified by the International and/or national federation(s) Figure 1 Volleyball equipment Type 1 Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 14:40:52 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 1271:2004 (E) 6 A complete volleyball equipment
29、 Type 1 shall have the following components: a) 2 posts (1 with tensioning device and 1 with rope attachment); b) 2 post pads (Classes A and B); c) 2 ground sockets; d) 1 net; e) 2 antennas (Classes A and B) f) 2 side bands (Classes A and B) Key 1 post 2 base assembly 3 floor fixing devices Other di
30、mensions and specifications as Type 1. Figure 2 Volleyball equipment Type 2 A complete volleyball equipment Type 2 shall have the following components: g) 2 posts (1 with tensioning device and 1 with rope attachment); h) for class B 2 post pads; i) 2 bases with floor fixing devices; j) 1 net; k) for
31、 Class B 2 antennas; l) for Class B 2 side bands. Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 14:40:52 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 1271:2004 (E) 7 3.3 Material 3.3.1 Posts The posts may be made of steel, light metal or synthetics, provided the requirements of this docume
32、nt are fulfilled. Light metal shall be non-corrosive and steel protected against corrosion (e. g. hot-galvanized, powder coated or painted). 3.3.2 Net The net shall be made from synthetic fibres. The top net line shall be made from galvanised, corrosion-resistant steel wires, synthetics or equivalen
33、t material. NOTE Plastic covering for steel wires is also acceptable. All tapes bordering the net shall be made from synthetic materials. 3.3.3 Antenna The antenna shall be made of glass-fibre reinforced plastics or similar material. 3.4 Design 3.4.1 Posts In the installed position the height adjust
34、ment of the net between the posts shall be possible between at least 2 000 mm to 2 500 mm from the sport surface. 3.4.2 Net The net of Classes A and B shall be black, the upper and lower edge bands and the side band shall be white. The net meshes shall be square. The top net line shall be inserted i
35、n the upper edge band. The net shall be stretched horizontally at its upper and lower corners by means of the tension ropes so that the top net line and bottom net line are parallel and 1 000 mm apart. Regarding the breaking forces of the net and its components the Classes of Tables 3 to 6 shall be
36、selected as appropriate. Table 3 Mesh breaking strength N Class min. Test method A1 800 (1 500)a B1 080 (900)a C 792 (660)a EN ISO 1806 a This corresponds to the breaking strength of the net yarn, tested in accor- dance with EN ISO 2062. Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 14:40:5
37、2 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 1271:2004 (E) 8 Table 4 Breaking forces of ropes/net lines N Class min. Test method A 5 000 B 3 400 C 1 100 prEN ISO 2307 Table 5 Breaking forces of top net line N Class min. Test method A 8 000 B 6 000 C 3 000 ISO 3108 Table 6 Breaking forces of net t
38、apes N Class min. Test method A 2 500 B 1 250 C 900 EN ISO 13934-1 3.4.3 Antennas For Classes A and B antennas shall be provided. They shall be marked alternately white/red above the net. The first section above the top tape shall be white (see Figure 1). The removable antenna pockets shall be attac
39、hed to both sides of the net vertically above the point of intersection between sideline and centre line of the play area. 3.4.4 Ground sockets For outdoor volleyball equipment the ground sockets shall be resistant to corrosion and provided with a drainage hole. 4 Safety requirements 4.1 General Exp
40、osed corners and edges shall be rounded with a radius of at least 3 mm. Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 14:40:52 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 1271:2004 (E) 9 4.2 Posts When tested in accordance with 5.2 each post for classes A and B shall not show any deflecti
41、on of more than 80 mm and no permanent deformation after release of the test force. The posts shall have the following mass: for class C type 1: a maximum of 20 kg; for class C type 2 equipped with wheels: a maximum of 30 kg. NOTEFor class A and B, the maximum mass of the posts is what is indicated
42、in the international federations (FIVB) regulations. 4.3Tensioning devices and rope attachment When tested according to 5.3, the locking mechanism of the tensioning device shall not release unintentionally. If handles are provided, e. g. the winch, they shall be removable, retractable or remain insi
43、de the post. Tensioning devices and rope attachments of classes A and B shall be outside the post side, i. e. away from the court, or fitted inside the post profile. In class C they can be fitted on the net side of the post with a maximum projection as specified in 5.1 of EN 913:1996. 4.4Post pads (
44、Classes A and B) Post pads shall be provided and fitted up to a height of 2 000 mm. When tested according to Annex C of EN 913:1996 with a drop height of 200 mm, the damping value of the pad- ding shall be below 50 g. 4.5 Base assembly The base assembly of the volleyball equipment Type 2 shall be ou
45、tside the court (see Figure 2) and shall be pro- tected because risk of hazards during the game, e. g. by padding with the damping characteristics of 4.4. 5 Test methods 5.1 General Requirements of Clauses 3 and 4, for which no particular tests are indicated in the following, shall be appropriately
46、verified, e.g. by measurement, visual inspection, tactile or functional testing. 5.2Testing of posts Place a force transducer within the top net line. Apply a force F of 1 200 N horizontally to the top net line at a height of 2 430 mm1) above the floor of the sports hall. Note the deflection of the
47、posts at the test height. Fully decrease the tension. Report any permanent deformation of the posts. 1) This is the competition height for men. Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 14:40:52 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 1271:2004 (E) 10 Apply a force F of 1 200 N ho
48、rizontally to the top net line at a height of 2 430 mm2) above the floor of the sports hall. Increase the tension up to 1,2 F (= 1 440) N and maintain the force for 1 min + 10 0 s. Report any change in the position of the tensioning device, the locking system and the net attachment. Fully decrease t
49、he tension. Report whether the locking mechanism of the tensioning device or the net attachment has released. 6Instructions for use Each volleyball equipment shall be accompanied by instructions for use including at least the following information: a)correct fastening of the net; b)handling of the tensioning device; c)storage; d)maintenance. 7 Marking Volleyball equipment complying this document shall be marked with the following information: a)the numb