《BS-EN-2149-1996.pdf》由会员分享，可在线阅读，更多相关《BS-EN-2149-1996.pdf（12页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD AEROSPACE SERIES BS EN 2149:1996 Rivets, solid, universal head, in aluminium alloy 5056A, anodized or chromated, inch based series The European Standard EN 2149:1996 has the status of a British Standard ICS 49.040.20 Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 02:49:19 GM
2、T+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 2149:1996 This British Standard, having been prepared under the direction of the Engineering Sector Board, was published under the authority of the Standards Board and comes into effect on 15 September 1996 BSI 07-1999 First published February 1992 Seco
3、nd edition August 1996 The following BSI references relate to the work on this standard: Committee reference ACE/12 Draft for comment 95/711798 DC ISBN 0 580 26141 7 Committees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee ACE/12,
4、 Aerospace fasteners and fastening systems, upon which the following bodies were represented: Association of Electronic, Telecommunications and Business Equipment Industries British Industrial Fasteners Federation Ministry of Defence Society of British Aerospace Companies Amendments issued since pub
5、lication Amd. No.DateComments Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 02:49:19 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 2149:1996 BSI 07-1999i Contents Page Committees responsibleInside front cover National forewordii Foreword2 1Scope3 2Normative references3 3Required characte
6、ristics3 4Designation6 5Marking6 6Technical specification6 Figure 14 Figure 26 Table 13 Table 24 Table 35 Table 46 List of referencesInside back cover Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 02:49:19 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 2149:1996 ii BSI 07-1999 National fo
7、reword This British Standard has been prepared by Technical Committee ACE/12 and is the English language version of EN 2149:1996 Aerospace series Rivets, solid, universal head, in aluminium alloy 5056A, anodized or chromated, inch based series, published by the European Committee for Standardization
8、 (CEN). It supersedes BS EN 2149:1993 which is withdrawn. EN 2149:1996 was produced as a result of international discussions in which the United Kingdom took an active part. Cross-references The British Standards corresponding to the European Standards referred to in the text are identical in number
9、 and title with those given in clause 2, with the exception of EN 2117, EN 2345 and EN 2347 for which no corresponding British Standards exist. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct appl
10、ication. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, the EN title page, pages 2 to 6, an inside back cover and a back cover. This standard has been updated
11、 (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 02:49:19 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 214
12、9 April 1996 ICS 49.040.20Supersedes EN 2149:1992 Descriptors: Aircraft industry, full rivet, round head rivet, aluminium alloy, anodized metal, dimension, designation, marking English version Aerospace series Rivets, solid, universal head, in aluminium alloy 5056A, anodized or chromated, inch based
13、 series Srie arospatiale Rivets ordinaires, tte ronde aplatie, en alliage daluminium 5056A, anodiss ou chromats, srie base inches Luft- und Raumfahrt Vollniete mit Universalkopf, aus Aluminiumlegierung 5056A, anodisiert oder chromatiert, Zoll-Reihe This European Standard was approved by CEN on 1995-
14、12-27. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtain
15、ed on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secret
16、ariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee
17、for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1996 Copyright reserved to CEN members Ref. No. EN 2149:1996 E Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 02:49:19 GMT+00:00 2006, Uncontrolled Copy,
18、 (c) BSI EN 2149:1996 BSI 07-1999 2 Foreword This European Standard has been prepared by the European Association of Aerospace Manufacturers (AECMA). After inquiries and votes carried out in accordance with the rules of this Association, this Standard has successively received the approval of the Na
19、tional Associations and the Official Services of the member countries of AECMA, prior to its presentation to CEN. This European Standard supersedes EN 2149:1992. This European Standard shall be given the status of a national Standard, either by publication of an identical text or by endorsement, at
20、the latest by October 1996, and conflicting national standards shall be withdrawn at the latest by October 1996. According to the CEN/CENELEC Internal Regulations, the national standards, organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Denmar
21、k, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 02:49:19 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 2149:1996 BSI 07-19993 1 Scope This st
22、andard specifies the characteristics of solid rivets, universal head, in aluminium alloy 5056A, anodized or chromated, inch based series, for maximum operating temperature 120 C. 2 Normative references This European Standard incorporates by dated or undated reference provisions from other publicatio
23、ns. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. Fo
24、r undated references the latest edition of the publication referred to applies. EN 2000, Aerospace series Quality assurance EN aerospace products Approval of the quality system of manufacturers. EN 2101, Aerospace series Chromic acid anodizing of aluminium and wrought aluminium alloys. EN 2117, Aero
25、space series Aluminium alloy 5056A-H32 wire for solid rivets D # 10 mm1). EN 2284, Aerospace series Sulphuric acid anodizing of aluminium and wrought aluminium alloys. EN 2345, Aluminium and aluminium alloy rivets Technical specification Aerospace series1). EN 2424, Aerospace series Marking of aeros
26、pace products. EN 2437, Aerospace series Chromate conversion coatings (yellow) for aluminium and aluminium alloys2). 3 Required characteristics 3.1 Configuration Dimensions Masses See Figure 1 and Table 2 and Table 3. Dimensions and tolerances are expressed in millimetres and apply after surface tre
27、atment. 3.2 Material EN 2117 3.3 Surface treatment See Table 1. Table 1 1) Published as AECMA Standard at the date of publication of the present standard 2) In preparation at the date of publication of the present standard NatureCode EN 2284BA EN 2437A1B EN 2101Ba Self-colored rivets (hyphen) Green-
28、colored rivetsF a For new products, it shall be replaced by EN 2284B. Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 02:49:19 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 2149:1996 4 BSI 07-1999 Table 2 Figure 1 Diameter codeD1aD2D3D4L2L3L4R1R2 max.min.max.min.max.min.max.min.max.min. 0,08
29、0161,651,553,353,05 1,61,20,7 1,4 2 0,150242,452,3554,52,41,81,91,610,80,52,9 0323,253,156,763,22,42,62,31,41 0,7 3,9 0363,653,557,56,83,62,72,92,51,6 1,6 1,14,4 0404,053,948,37,5433,22,81,71,20,84,9 0484,854,731094,83,63,83,32 2 1,515,9 0565,655,5311,710,55,64,24,53,92,41,81,26,8 0,25 0646,456,3313
30、,312,16,44,85,14,52,72,11,47,8 0808,037,916,715,1866,45,63,42,41,69,8 0969,639,52018,19,67,27,76,74,13211,7 a D1 max. may increase by 0,03, over length L3. + 0,2 0 Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 02:49:19 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 2149:1996 BSI 07-19995 Tab
31、le 3 Diameter code016024032036040048056064080096 Length Massb a Massb a Massb a Massb a Massb a Massb a Massb a Massb a Massb a Massb CodeL1+ 0,5 0 NRNRNRNRNRNRNRNRNR 00330,030 00440,0360,0830,1760,227 00550,0410,0950,1980,254 00660,0460,1070,2200,2800,373 00770,0520,1190,2420,3060,408 00880,0570,13
32、10,2640,3320,4430,664 00990,0630,1430,2860,3580,4780,714 010100,0680,1550,3080,3840,5130,7641,1371,556 011110,0740,1670,3300,4100,5480,8141,2051,645 012120,0790,1790,3520,4360,5830,8641,2731,734 013130,0850,1910,3740,4620,6180,9141,3411,8233,127 014140,0900,2030,3960,4880,6530,9641,4091,9123,266 015
33、150,0960,2150,4180,5150,6881,0141,4772,0013,405 016160,1010,2270,4400,5410,7231,0641,5452,0903,544 017170,2390,4620,5670,7581,1141,6132,1793,6835,669 018180,2510,4840,5930,7931,1641,6812,2683,8225,868 019190,2630,5060,6190,8281,2141,7482,3573,9616,067 020200,2750,5280,6450,8631,2641,8172,4464,1006,2
34、66 022220,2990,5720,6970,9331,3641,9532,6244,3786,664 024240,3230,6160,7491,0031,4642,0892,8024,6567,062 026260,3470,6600,8021,0731,5642,2252,9804,9347,460 028280,3710,7040,8541,1431,6642,3613,1585,2127,858 030300,3950,7480,9061,2131,7642,4973,3365,4908,256 032320,4190,7920,9581,2831,8642,6333,5145,
35、7688,654 035350,4550,8581,0371,3882,0142,8373,7816,1859,251 040400,9681,1671,5632,2643,1774,2266,88010,246 045451,2981,7382,5143,5174,6717,57511,241 050501,9132,7643,8575,1168,27012,236 055553,0144,1975,5618,96513,231 060603,2644,5376,0069,66014,226 a Tail end code (see Figure 1) b Approximate value
36、s (kg/1 000 pieces), calculated on the basis of 2,76 kg/dm3, given for information purposes only Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 02:49:19 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 2149:1996 6 BSI 07-1999 4 Designation EXAMPLE: NOTEIf necessary, the code 19005 shall be plac
37、ed between the description block and the identity block. 5 Marking 5.1 Rivet EN 2424, style G 5.2 Material See Figure 2 and Table 4. Table 4 6 Technical specification EN 2345 plus EN 2000 for the approval of manufacturers Figure 2 Diameter code016024032036040048056064080096 T 0,050,130,150,2 S max.0
38、,8 D5 max.= D1 max. (see Table 2.) Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 02:49:19 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 2149:1996 BSI 07-1999 List of references See national foreword. Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 02:49:19 GMT+00:00 2006, Uncontro
39、lled Copy, (c) BSI BS EN 2149:1996 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal C
40、harter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inac
41、curacy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures t
42、hat subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI
43、 policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Ser
44、vice. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discoun
45、ts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the internationalstandardiza
46、tion bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude
47、the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070. Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 02:49:19 GMT+00:00 2006, Uncontrolled Copy, (c) BSI