《BS-EN-1715-3-2008.pdf》由会员分享，可在线阅读，更多相关《BS-EN-1715-3-2008.pdf（10页珍藏版）》请在三一文库上搜索。
1、BS EN 1715-3:2008 ICS 77.150.10 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BRITISH STANDARD Aluminium and aluminium alloys Drawing stock Part 3: Specific requirements for mechanical uses (excluding welding) Licensed Copy: London South Bank University, South Bank Universit
2、y, 31/01/2009 03:12, Uncontrolled Copy, (c) BSI This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 2008 BSI 2008 ISBN 978 0 580 57007 0 Amendments/corrigenda issued since publication DateComments BS EN 1715-3:2008 National foreword This Briti
3、sh Standard is the UK implementation of . It supersedes BS EN 1715-3:1998 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee NFE/35, Light metals and their alloys. A list of organizations represented on this committee can be obtained on request to its se
4、cretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. December Licensed Copy: London South Bank University, South Bank Univ
5、ersity, 31/01/2009 03:12, Uncontrolled Copy, (c) BSI BS EN 1715-3:2008BS EN 1715-3:2008BS EN 1715-3:2008 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1715-3 April 2008 ICS 77.150.10Supersedes EN 1715-3:1997 English Version Aluminium and aluminium alloys - Drawing stock - Part 3: Specific req
6、uirements for mechanical uses (excluding welding) Aluminium et alliages daluminium - Fil machine - Partie 3: Exigences spcifiques relatives aux applications mcaniques (soudage except) Aluminium und Aluminiumlegierungen - Vordraht - Teil 3: Besondere Anforderungen fr mechanische Anwendungen (ausgenom
7、men Schweien) This European Standard was approved by CEN on 14 March 2008. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliog
8、raphical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of
9、 a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Irela
10、nd, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart,
11、 36 B-1050 Brussels 2008 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1715-3:2008: E Licensed Copy: London South Bank University, South Bank University, 31/01/2009 03:12, Uncontrolled Copy, (c) BSI BS EN 1715-3:2008BS EN 1715-3:2
12、008BS EN 1715-3:2008 EN 1715-3:2008 (E) 2 Contents Page Foreword3 1 Scope 4 2 Normative references4 3 Requirements.4 3.1 Chemical composition 4 3.2 Temper for delivery6 4 Product inspection and testing methods6 4.1 Chemical composition 6 4.2 Mechanical properties.6 5 Delivery documents and inspectio
13、n documents6 6 Marking and packaging.7 Licensed Copy: London South Bank University, South Bank University, 31/01/2009 03:12, Uncontrolled Copy, (c) BSI BS EN 1715-3:2008BS EN 1715-3:2008BS EN 1715-3:2008 EN 1715-3:2008 (E) 3 Foreword This document (EN 1715-3:2008) has been prepared by Technical Comm
14、ittee CEN/TC 132 “Aluminium and aluminium alloys”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2008, and conflicting national standards shall
15、 be withdrawn at the latest by October 2008. This document supersedes EN 1715-3:1997. Within its programme of work, Technical Committee CEN/TC 132 entrusted CEN/TC 132/WG 4 “Wires and drawing stock“ to revise EN 1715-3:1997. Besides editorial adjustments in the text and update of normative reference
16、s, the following changes have been made: Clause 3: amended; Table 1: values modified, alloy EN AW-5086 deleted, alloy EN AW-6056 added, new tempers for alloys EN AW-6060, EN AW-6061 and EN AW-6082 added EN 1715 comprises the following parts under the general title “Aluminium and aluminium alloys Dra
17、wing stock“: Part 1: General requirements and technical conditions for inspection and delivery Part 2: Specific requirements for electrical applications Part 3: Specific requirements for mechanical uses (excluding welding) Part 4: Specific requirements for welding applications Part 5: Specific requi
18、rements for aluminium food packaging1) Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. CEN/TC 132 affirms that it is its policy that in the case when
19、 a patentee refuses to grant licenses on standardised standard products under reasonable and not discriminatory conditions, then this product is removed from the corresponding standard. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries
20、 are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, S
21、weden, Switzerland and the United Kingdom. 1) Under preparation. Licensed Copy: London South Bank University, South Bank University, 31/01/2009 03:12, Uncontrolled Copy, (c) BSI BS EN 1715-3:2008BS EN 1715-3:2008BS EN 1715-3:2008 EN 1715-3:2008 (E) 4 1 Scope This European Standard specifies specific
22、 requirements for drawing stock of aluminium and aluminium alloys for general mechanical uses (excluding welding). The general requirements and technical conditions for inspection and delivery are specified in EN 1715-1. This European Standard does not apply to drawn wire. 2 Normative references The
23、 following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 515, Aluminium and aluminium alloys Wrought produ
24、cts Temper designations EN 573-3, Aluminium and aluminium alloys Chemical composition and form of wrought products Part 3: Chemical composition and form of products EN 1715-1, Aluminium and aluminium alloys Drawing stock Part 1: General requirements and technical conditions for inspection and delive
25、ry 3 Requirements 3.1 Chemical composition Aluminium and aluminium alloys used commonly for mechanical uses (excluding welding) are given in Table 1. Their chemical composition shall be in accordance with EN 573-3. The elements determined and reported in the certificate of mass and analysis shall be
26、 : Si, Fe, Cu, Mn, Mg, Cr, Ni, Zn, Ti, Ga and V. If other elements (e.g. Pb, Bi, Zr.) are specified in EN 573-3, they shall be determined and reported in the certificate of mass and analysis. Licensed Copy: London South Bank University, South Bank University, 31/01/2009 03:12, Uncontrolled Copy, (c)
27、 BSI BS EN 1715-3:2008BS EN 1715-3:2008BS EN 1715-3:2008 EN 1715-3:2008 (E) 5 Table 1 Main alloys for mechanical purposes - Tempers for delivery Typical tensile strength values Alloy designation Temper Tensile strength typical range Rm MPa Continuously cast rod Hot rolled and extruded rod 1 000 Seri
28、e EN AW-1098 Al 99,98 F 75 to 85 75 to 85 EN AW-1080A Al 99,8(A) F 80 to 110 80 to 110 O 60 to 75 60 to 75 EN AW-1070A Al 99,7 F 80 to 110 80 to 110 O 60 to 75 60 to 75 EN AW-1050A Al 99,5 F 80 to 130 80 to 130 O 60 to 80 60 to 80 2 000 Serie EN AW-2011 Al Cu6BiPb F 170 to 230 170 to 400 O3 110 to 1
29、70 110 to 170 EN AW-2014A Al Cu4 SiMg(A) F 200 to 260 200 to 400 O/O3 150 to 220 150 to 220 EN AW-2017A Al Cu4 MgSi(A) F 200 to 260 200 to 400 O/O3 150 to 220 150 to 220 EN AW-2117 Al Cu2,5Mg F 170 to 230 170 to 360 O/O3 140 to 200 140 to 200 EN AW-2024 Al Cu4Mg1 F 200 to 280 200 to 440 O/O3 180 to
30、240 180 to 240 3 000 Serie EN AW-3003 Al Mn1Cu F 120 to 220 120 to 220 O3 95 to 120 95 to 120 EN AW-3103 Al Mn1 F 120 to 220 120 to 220 O3 95 to 115 95 to 115 5 000 Serie EN AW-5051A Al Mg2(B) F 170 to 230 EN AW-5251 Al Mg2Mn0,3 F 170 to 230 EN AW-5052 Al Mg2,5 F 180 to 260 EN AW-5154A Al Mg3,5(A) F
31、 210 to 280 O3 210 to 250 EN AW-5754 Al Mg3 F 200 to 260 O3 200 to 250 EN AW-5019 Al Mg5 F 250 to 320 O/O3 250 to 310 6 000 Serie EN AW-6056 Al Si1MgCuMn F 160 to 230 O3 140 to 180 T4 300 to 380 EN AW-6060 Al MgSi F 120 to 190 T4 155 to 210 EN AW-6061 Al Mg1SiCu F 120 to 200 O3 90 to 140 T4 220 to 2
32、80 EN AW-6063 Al Mg0,7Si T4 160 to 220 EN AW-6082 Al Si1MgMn F 130 to 220 O3 100 to 150 T4 230 to 290 7 000 Serie EN AW-7075 Al Zn5,5MgCu O/O3 180 to 290 Licensed Copy: London South Bank University, South Bank University, 31/01/2009 03:12, Uncontrolled Copy, (c) BSI BS EN 1715-3:2008BS EN 1715-3:200
33、8BS EN 1715-3:2008 EN 1715-3:2008 (E) 6 3.2 Temper for delivery The variety of application of drawn wire made from drawing stock of aluminium and aluminium alloys used for mechanical applications requires a precise definition of the temper for delivery which is liable to exert a significant influenc
34、e on the ability to process and on the final characteristics. Tempers shall be indicated in accordance with EN 515. The usual tempers for drawing stock covered by this European Standard are: F: as fabricated; O: annealed; O3: homogenised; T4: solution heat treated and naturally aged. These tempers a
35、re listed in Table 1 with typical ranges of mechanical characteristics (tensile strength). If no temper is specified when ordering, the delivered temper shall be F. Other tempers shall be agreed between manufacturer and purchaser. 4 Product inspection and testing methods 4.1 Chemical composition The
36、 chemical composition shall be checked for each cast delivered in accordance with EN 1715-1. 4.2 Mechanical properties The mechanical properties shall be at least measured once per coil in accordance with EN 1715-1. Other sampling frequencies shall be agreed between manufacturer and purchaser. 5 Del
37、ivery documents and inspection documents A certificate of mass and analysis shall be provided in accordance with EN 1715-1. In addition, a test report in accordance with EN 1715-1 shall be delivered for each cast in a consignment with reference to the order, and giving the following information: ide
38、ntification of the alloy; temper; diameter; list of coil identification numbers; results of test for mechanical properties; date of manufacture; Licensed Copy: London South Bank University, South Bank University, 31/01/2009 03:12, Uncontrolled Copy, (c) BSI BS EN 1715-3:2008BS EN 1715-3:2008BS EN 17
39、15-3:2008 EN 1715-3:2008 (E) 7 date of heat treatment, if any; net mass. NOTE Other inspection documents can be defined between manufacturer and purchaser in accordance with EN 1715-1. 6 Marking and packaging Marking and packaging shall be carried out in accordance with EN 1715-1. Licensed Copy: Lon
40、don South Bank University, South Bank University, 31/01/2009 03:12, Uncontrolled Copy, (c) BSI BS EN 1715-3:2008 BSI Group Headquarters 389 Chiswick High Road, London, W4 4AL, UK Tel +44 (0)20 8996 9001 Fax +44 (0)20 8996 7001 standards BSI - British Standards Institution BSI is the independent nat
41、ional body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess
42、the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of
43、 which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international a
44、nd foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001 Email: You may also buy directly using a debit/credit card from the BSI Shop on the Website http:/ In response to orders for international standards, it is BSI policy to su
45、pply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various
46、 BSI electronic information services are also available which give details on all its products and services. Contact Information Centre. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing members of BSI are kept up to date with standards developments and receive substantial discou
47、nts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via British Standards Online can be found at http:/ Further informatio
48、n about BSI is available on the BSI website at http:/ . Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may
49、 be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, t