《BS-EN-12421-1998.pdf》由会员分享，可在线阅读，更多相关《BS-EN-12421-1998.pdf（8页珍藏版）》请在三一文库上搜索。
1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS EN 12421:1998 The Euro
2、pean Standard EN 12421:1998 has the status of a British Standard ICS 77.120.20 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Magnesium and magnesium alloys Unalloyed magnesium Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 08:51:15 GMT+00:00 2006, Uncontrolled Copy,
3、(c) BSI This British Standard, having been prepared under the direction of the Engineering Sector Board, was published under the authority of the Standards Board and comes into effect on 15 November 1998 BSI 1998 ISBN 0 580 29992 9 BS EN 12421:1998 Amendments issued since publication Amd. No.DateTex
4、t affected National foreword This British Standard is the English language version of EN 12421:1998. The UK participation in its preparation was entrusted by Technical Committee NFE/35, Light metals and their alloys, to Subcommittee NFE/35/4, Magnesium and magnesium alloys, which has the responsibil
5、ity to: aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations
6、 represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled International Standards Cor
7、respondence Index, or by using the Find facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not
8、 of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 5 and a back cover. Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 08:51:15 GMT+00:00 2006, Uncontrolled Copy, (c) BSI CEN European
9、Committee for Standardization Comite Europe en de Normalisation Europa isches Komitee fu r Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1998 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12421:1998 E EUROPEAN
10、STANDARDEN 12421 NORME EUROPE ENNE EUROPA ISCHE NORM April 1998 ICS 77.120.20 Descriptors: Magnesium, chemical composition, designation, quality, classification, marking, tests English version Magnesium and magnesium alloys Unalloyed magnesium Magne sium et alliages de magne sium Magne sium non alli
11、e Magnesium und Magnesiumlegierungen Reinmagnesium This European Standard was approved by CEN on 25 March 1998. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alt
12、eration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by tran
13、slation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland,
14、 Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 08:51:15 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Page 2 EN 12421:1998 BSI 1998 Foreword This European Standard has been prepared by Technical Co
15、mmittee CEN/TC 190, Foundry technology, the secretariat of which is held by DIN. Within its programme of work, Technical Committee CEN/TC 190 requested CEN/TC 190/WG 3.10, Cast magnesium, to prepare the following standard: EN 12421, Magnesium and magnesium alloys Unalloyed magnesium. This European S
16、tandard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 1998, and conflicting national standards shall be withdrawn at the latest by October 1998. According to the CEN/CENELEC Internal Regulations, the national
17、standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Conten
18、ts Page Foreword2 Introduction3 1Scope3 2Normative references3 3Definitions3 3.1unalloyed magnesium3 3.2cast unalloyed magnesium3 4Information to be supplied by the purchaser3 5Designation3 6Manufacture3 7Requirements3 7.1Chemical composition3 7.2General condition of the product3 8Testing3 9Rounding
19、 of numbers3 10Declaration of conformity and inspection documents3 11Marking5 12Complaints5 Annex A (informative) Bibliography5 Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 08:51:15 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Page 3 EN 12421:1998 BSI 1998 Introduction This European Standard
20、 classifies the commercially available cast unalloyed magnesium into a number of grades suitable for the applications to which they might be put. 1 Scope This European Standard specifies the chemical composition of cast unalloyed magnesium. It specifies classification, designation and marking. 2 Nor
21、mative references This European Standard incorporates, by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions
22、of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references, the latest edition of the publication referred to applies. ISO 31-0:1992, Quantities and units Part 0: General principles. NOTEInformative references to documen
23、ts used in the preparation of this standard and cited at the appropriate places in the text, are listed in a bibliography, see annex A. 3 Definitions For the purposes of this standard the following definitions apply. 3.1 unalloyed magnesium magnesium with a minimum mass fraction of 99,0 % 3.2 cast u
24、nalloyed magnesium unalloyed magnesium cast in a variety of shapes 4 Information to be supplied by the purchaser The enquiry and order shall define the product required and shall contain the following information: a) material designation; b) product shape; c) quantity (e.g. number, mass, etc.); d) a
25、ny requirements for declarations of conformity; e) any additional requirements agreed between the manufacturer and the purchaser. 5 Designation The material shall be designated either by symbol or by number (see Table 1). 6 Manufacture The manufacturing process shall be left to the discretion of the
26、 manufacturer unless otherwise agreed at the time of ordering. NOTEThe manufacturing process covers all operations up to the delivery of the product. 7 Requirements 7.1 Chemical composition The chemical composition of cast unalloyed magnesium shall conform to the requirements for the appropriate mat
27、erial given in Table 1. If not otherwise specified in the enquiry and order, the chemical composition of the cast unalloyed magnesium shall relate to that of the samples taken from the melt at the time of pouring. 7.2 General condition of the product The product shall have a clean surface and shall
28、be commercially free from visible and internal defects to a standard agreed between the manufacturer and the purchaser. 8 Testing For analysis of chemical composition, samples shall be taken by the manufacturer to assure conformance to the chemical composition requirements given in Table 1 and shall
29、 be representative of the material delivered. 9 Rounding of numbers In recording chemical analysis, the number representing the result for any value specified in this standard shall be expressed to the same number of decimal places as the corresponding number in this standard. The rounding of number
30、s shall meet the requirements of ISO 31-0:1992, annex B, clause B.3, rule A or B. The choice shall be left to the discretion of the manufacturer, unless the use of one of the rules is agreed by the time of acceptance of the order. 10 Declaration of conformity and inspection documents If agreed betwe
31、en the manufacturer and the purchaser or when specified on the order, the manufacturer shall provide a declaration of product conformity or an inspection document listing the results of the analysis of the chemical elements given in Table 1, and of any other element which may have been previously ag
32、reed. Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 08:51:15 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BSI 1998 Page 4 EN 12421:1998 Table 1 Chemical composition of cast unalloyed magnesium Material designationChemical composition in per cent (mass fraction) SymbolNumberElementAlMnSiFeCuNi
33、PbSnNaCaZnOthers each Mg1) EN-MB99,5EN-MB10010min.99,5 max.0,10,10,10,10,10,010,010,010,05 EN-MB99,80-AEN-MB10020min.99,80 max.0,050,050,050,050,020,0010,010,010,0030,0030,050,05 EN-MB99,80-BEN-MB10021min.99,80 max.0,050,050,050,050,020,0020,010,010,050,05 EN-MB99,95-AEN-MB10030min.99,95 max.0,010,0
34、060,0060,0030,0050,0010,0050,0050,0030,0030,0050,005 EN-MB99,95-BEN-MB10031min.99,95 max.0,010,010,010,0050,0050,0010,0050,0050,010,005 1) By difference. NOTEThe material designation is in accordance with EN 1754. Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 08:51:15 GMT+00:00 2006, Uncont
35、rolled Copy, (c) BSI Page 5 EN 12421:1998 BSI 1998 11 Marking Unless otherwise agreed, each product, or bundle of products, shall be clearly marked with the following: manufacturers identification; material designation; melt identification; unit weight (mass). The method of marking is left to the di
36、scretion of the manufacturer. Markings shall be indelible and shall not be a source of contamination. 12 Complaints In case of any product complaint, the manufacturer shall be able to examine the validity of the complaint within a reasonable time. Complaints may only be raised against defective prod
37、ucts if the defect impairs their processing and use to a more than negligible extent. This shall apply unless otherwise agreed by the time of acceptance of the order. The purchaser shall give the manufacturer the opportunity to judge whether the complaints are justified. Annex A (informative) Biblio
38、graphy In the preparation of this European Standard, use was made of a document for reference purposes. This informative reference is cited at the appropriate place in the text and the publication is listed hereafter. EN 1754, Magnesium and magnesium alloys Magnesium and magnesium alloy anodes, ingo
39、ts and castings Designation system. Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 08:51:15 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
40、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe
41、 and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our product
42、s and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers memb
43、ers an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001
44、. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standar
45、ds through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to da
46、te with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright,
47、in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise wit
48、hout prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permis
49、sion of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070. Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 08:51:15 GMT+00:00 2006, Uncontrolled Copy, (c) BSI