《BS-EN-13565.pdf》由会员分享，可在线阅读，更多相关《BS-EN-13565.pdf（34页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 13565-1:2003 +A1:2007 Fixed firefighting systems Foam systems Part 1: Requirements and test methods for components ICS 13.220.20 ? Licensed Copy: London South Bank University, South Bank University, 16/11/2008 11:53, Uncontrolled Copy, (c) BSI BS EN 13565-1:2003+A1:2007 This B
2、ritish Standard was published under the authority of the Standards Policy and Strategy Committee on 11 February 2004 BSI 2008 ISBN 978 0 580 63713 1 National foreword This British Standard is the UK implementation of EN 13565-1:2003+A1:2007. It supersedes BS EN 13565-1:2003 which is withdrawn. The s
3、tart and finish of text introduced or altered by amendment is indicated in the text by tags. Tags indicating changes to CEN text carry the number of the CEN amendment. For example, text altered by CEN amendment A1 is indicated by !“. The UK participation in its preparation was entrusted by Technical
4、 Committee FSH/18, Fixed fire fighting systems, to Subcommittee FSH/18/7, Foam systems. A list of organizations represented on this subcommittee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible
5、 for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. Amendments/corrigenda issued since publication DateComments 30 September 2008Implementation of CEN amendment A1:2007 Licensed Copy: London South Bank University, South Bank University, 16/
6、11/2008 11:53, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13565-1:2003+A1 October 2007 ICS 13.220.20 Supersedes EN 13565-1:2003 English Version Fixed firefighting systems - Foam systems - Part 1: Requirements and test methods for components Installations fixes de
7、 lutte contre lincendie - Systmes mulseurs - Partie 1: Exigences et mthodes dessai relatives aux composants Ortsfeste Brandbekmpfungsanlagen - Schaumlschanlagen - Teil 1: Anforderungen und Prfverfahren fr Bauteile This European Standard was approved by CEN on 21 November 2003 and includes Amendment
8、1 approved by CEN on 13 September 2007. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such
9、 national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language
10、 and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxem
11、bourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2007 CEN All ri
12、ghts of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13565-1:2003+A1:2007: E Licensed Copy: London South Bank University, South Bank University, 16/11/2008 11:53, Uncontrolled Copy, (c) BSI EN 13565-1:2003+A1:2007 (E) 2 Contents page Foreword4 In
13、troduction.5 1 Scope 6 2 Normative references6 3 Terms and definitions .7 4 General construction requirements.9 4.1 Connections.9 4.2 Parts intended for removal during routine field maintenance10 4.3 Hydrostatic strength10 4.4 Castings10 4.5 Corrosion resistance of metal parts10 4.6 Elastomeric join
14、t rings11 4.7 Plastics and reinforced resin materials.11 4.8 Heat and fire resistance 12 5 Discharge coefficients and characteristics of branchpipes, sprayers and low and high back- pressure foam generators 12 5.1 Single orifice components12 5.2 Multiple orifice components.12 6 Quality of foam from
15、aspirating components.12 6.1 Low and medium expansion components12 6.2 High expansion components13 7 Accuracy of proportioning components.13 8 Components for low expansion foam systems13 8.1 Foam branchpipes (hand and monitor).13 8.2 Foam sprayers .13 8.3 Foam pourers and foam chambers13 8.4 Vapour
16、seals.13 8.5 Low back-pressure and high back-pressure foam generators.14 8.6 Semi-subsurface hose units.14 9 Components for medium and high expansion foam systems14 9.1 Nozzles and sprayers14 9.2 High expansion foam generators.14 10 Tanks and pressure vessels for foam concentrates or solutions14 10.
17、1 General14 10.2 Tanks at atmospheric pressure15 10.3 Pressure vessels15 11 Marking.15 12 Evaluation of conformity.15 12.1 General15 12.2 Initial type testing 16 12.3 Factory production control (FPC)17 Annex A (normative) Hydrostatic test.19 Annex B (normative) Ageing test for plastics and reinforce
18、d resin materials .20 B.1 General20 B.2 Tensile strength and elongation test.20 B.3 Impact test20 BS EN 13565-1:2003+A1:2007 Licensed Copy: London South Bank University, South Bank University, 16/11/2008 11:53, Uncontrolled Copy, (c) BSI EN 13565-1:2003+A1:2007 (E) 3 Annex C (normative) Liquid expos
19、ure test.21 Annex D (normative) Heat and fire resistance test for foam generators 22 Annex E (normative) Flow tests 23 E.1 General23 E.2 Discharge coefficient 23 E.3 Discharge characteristic.23 Annex F (normative) Quality of foam from aspirating components24 F.1 General24 F.2 Low expansion foams.24
20、F.3 Medium expansion foams.24 F.4 High expansion foams 24 Annex G (normative) High expansion foam generator test25 Annex H (normative) Range tests for branchpipes (hand and monitor).26 Annex I (normative) Area coverage test for foam sprayers and nozzles27 Annex J (normative) Maximum flow and back pr
21、essure.28 J.1 General28 J.2 Maximum flow28 J.3 Back pressure28 Annex K (normative) Insertion and deployment of semi-subsurface hose29 BS EN 13565-1:2003+A1:2007 Licensed Copy: London South Bank University, South Bank University, 16/11/2008 11:53, Uncontrolled Copy, (c) BSI EN 13565-1:2003+A1:2007 (E
22、) 4 Foreword This document (EN 13565-1:2003+A1:2007) has been prepared by Technical Committee CEN /TC 191, “Fixed firefighting systems“ the secretariat of which is held by BSI. This document shall be given the status of a national standard, either by publication of an identical text or by endorsemen
23、t, at the latest by April 2008 and conflicting national standards shall be withdrawn at the latest by April 2008. This document includes Amendment 1, approved by CEN on 2007-09-13. This document supersedes EN 13565-1:2003. The start and finish of text introduced or altered by amendment is indicated
24、in the text by tags ! “. !deleted text“ According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Gr
25、eece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. BS EN 13565-1:2003+A1:2007 Licensed Copy: London South Bank University, South Bank University, 16/11/2008 1
26、1:53, Uncontrolled Copy, (c) BSI EN 13565-1:2003+A1:2007 (E) 5 Introduction This European Standard covers components intended for use in fixed fire fighting foam systems. BS EN 13565-1:2003+A1:2007 Licensed Copy: London South Bank University, South Bank University, 16/11/2008 11:53, Uncontrolled Cop
27、y, (c) BSI EN 13565-1:2003+A1:2007 (E) 6 1 Scope This European Standard specifies requirements for materials, construction, and performance of components intended for use in fixed foam fire fighting systems, and using foam concentrates conforming to EN 1568-1 to EN 1568-4. The components covered are
28、: proportioners, sprayers, semi-subsurface hose units, branchpipes, low/medium expansion foam generators, high expansion foam generators, foam chambers, tanks and pressure vessels. Methods of test are given in annexes A to K. Requirements are also given for the provision of the characteristic data n
29、eeded for correct application of components. NOTE 1 Unless otherwise stated pressures are gauge pressures expressed in bar. The requirements of this specification do not cover, except where stated, the use of combinations of components to form part, or the whole, of a fire fighting system. NOTE 2 It
30、 should not be assumed that components conforming to this specification are necessarily compatible one with another. Requirements for pumps, motors and the functioning of mechanical components (i.e. remote control turrets) are outside the scope of this standard. 2 Normative references This European
31、Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications appl
32、y to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies (including amendments). EN 671-1:2001, Fixed firefighting systems - Hose systems - Part 1: Hose reels with semi-rigid hose EN 1568-1: 20
33、00, Fire extinguishing media - Foam concentrates - Part 1: Specification for medium expansion foam concentrates for surface application to water-immiscible liquids EN 1568-2:2000, Fire extinguishing media - Foam concentrates - Part 2: Specification for high expansion foam concentrates for surface ap
34、plication to water-immiscible liquids EN 1568-3:2000, Fire extinguishing media - Foam concentrates - Part 3 Specification for low expansion foam concentrates for surface application to water-immiscible liquids EN 1568-4, Fire extinguishing media - Foam concentrates - Part 4: Specification for low ex
35、pansion foam concentrates for surface application to water-miscible liquids !EN 12259-1:1999+A1:2001“, Fixed fire fighting systems Components for sprinkler and water spray systems - Part 1: Sprinklers EN 12416-1:2001, Fixed firefighting systems - Powder systems - Part 1: Requirements and test method
36、s for components EN 12542, Static welded steel cylindrical tanks, serially produced for the storage of Liquified Petroleum Gas (LPG) having a volume not greater than 13 m3 and for installation above ground - Design and manufacture EN 20225, Fasteners - Bolts, screws, studs and nuts Symbols, designat
37、ions and dimensions (ISO 225:1983) EN ISO 175, Plastics - Methods of test for the determination of the effects of immersion in liquid chemicals (ISO 175:1999) BS EN 13565-1:2003+A1:2007 Licensed Copy: London South Bank University, South Bank University, 16/11/2008 11:53, Uncontrolled Copy, (c) BSI E
38、N 13565-1:2003+A1:2007 (E) 7 EN ISO 179-1, Plastics - Determination of Charpy impact properties - Part 1: Non-instrumented impact test (ISO 179-1:2000) EN ISO 180, Plastics - Determination of Izod impact strength (ISO 180:2000) EN ISO 228-1, Pipe threads where pressure-tight joints are not made on t
39、he threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000) EN ISO 527-1, Plastics - Determination of tensile properties - Part 1: General principles (ISO 527-1:1993 including Corr 1:1994) EN ISO 898-1, Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1
40、: Bolts, screws and studs (ISO 898-1:1999) EN ISO 4759-1, Tolerances for fasteners - Part 1: Bolts, screws, studs and nuts - Product grades A, B and C (ISO 4759-1:2000) EN ISO 9001:2000 Quality management systems Requirements (ISO 9001:2000) ISO 7-1, Pipe threads where pressure-tight joints are made
41、 on the threads - Part 1: Dimensions, tolerances and designation ISO 272, Fasteners - Hexagon products - Widths across flats ISO 885, General purpose bolts and screws - Metric series - Radii under the head ISO 888, Bolts screws and studs - Nominal lengths and thread length for general purpose bolts
42、ISO 1179-1, Connections for general use and fluid power - Ports and stud ends with EN ISO 228-1 threads with elastomeric or metal-to-metal sealing - Part 1: Threaded ports (Revision of ISO 1179:1981) ISO 4633, Rubber seals - Joint rings for water supply, drainage and sewerage pipelines - Specificati
43、on for material ISO 6447, Rubber seals - Joint rings used for gas supply pipes and fittings - Specification for material ISO 6448, Rubber seals - Joint rings used for petroleum product supply pipes and fittings - Specification for material ISO 7005-1, Metallic flanges; Part 1: Steel flanges ISO 7005
44、-2, Metallic flanges; Part 2: Cast iron flanges ISO 9227, Corrosion tests in artificial atmospheres; salt spray tests Nordtest method NT Fire 042 3 Terms and definitions For the purposes of this European Standard, the following terms and definitions apply. 3.1 aspirating component component within w
45、hich air and foam solution are mixed to make foam 3.2 branchpipe component which projects foam in the form of a jet or spray BS EN 13565-1:2003+A1:2007 Licensed Copy: London South Bank University, South Bank University, 16/11/2008 11:53, Uncontrolled Copy, (c) BSI EN 13565-1:2003+A1:2007 (E) 8 3.3 c
46、omponent item or piece of equipment intended for use in a fixed foam fire extinguishing system 3.4 discharge coefficient (K factor) K factor for the equation Q = KdP where Q is the flow rate through the component in l/min and dp is the inlet pressure in bar 3.5 high back pressure foam generator comp
47、onent which introduces air into the foam solution stream for delivery against a high back pressure, for example, as is found in tank sub-surface injection 3.6 high expansion foam foam which has an expansion ratio greater than 200 3.7 foam generator component which introduces air into the foam soluti
48、on stream for delivery against a low back pressure, i.e. discharging against atmospheric pressure 3.8 low expansion foam foam which has an expansion ratio not greater than 20 3.9 foam chamber component that incorporates a vapour seal, a foam expansion chamber, and which delivers foam into a flammabl
49、e or combustible liquid storage tank. A foam generator may be connected to the foam chamber inlet 3.10 medium expansion foam foam which has an expansion ratio greater than 20 but not greater than 200 3.11 monitor component consisting of a branchpipe and turret 3.12 non-aspirating components components which discharge a spray of foam solution so that mixing with air and formation of foam takes place outside the component 3.13 fixed foam pourer (foam discharge outlet) component which d