《BS-EN-130200-1993.pdf》由会员分享，可在线阅读，更多相关《BS-EN-130200-1993.pdf（30页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 130200:1993 Incorporating Amendment No. 1 Harmonized system of quality assessment for electronic components Sectional specification: Fixed tantalum capacitors with non-solid or solid electrolyte The European Standard EN 130200:1993, with the incorporation of its amendment A3:1
2、998, has the status of a British Standard ICS 31.060.40 Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 10:39:47 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 130200:1993 This British Standard, having been prepared under the direction of the Electronic Components Standards Policy Committee
3、, was published under the authority of the Standards Board and comes into effect on 15 December 1993 BSI 06-1999 The following BSI references relate to the work on this standard: Committee reference ECL/4 Special announcement in BSI News, September 1993 ISBN 0 580 22727 8 Cooperating organizations T
4、he European Committee for Electrotechnical Standardization (CENELEC), under whose supervision this European Standard was prepared, comprises the national committees of the following countries: AustriaItaly BelgiumLuxembourg DenmarkNetherlands FinlandNorway FrancePortugal GermanySpain GreeceSweden Ic
5、elandSwitzerland IrelandUnited Kingdom Amendments issued since publication Amd. No.DateComments 10078January 1999 See foreword to amendment A3 on page 2 NOTEThere was no amendment 1 to EN 130200 Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 10:39:47 GMT+00:00 2006, Uncontrolled Copy, (c) BS
6、I BS EN 130200:1993 BSI 06-1999i Contents Page Cooperating organizations Inside front cover National foreword ii Foreword 2 Text of EN 130200 5 National annex NA (informative) Committees responsible Inside back cover National annex NB (informative) Cross-references Inside back cover Licensed Copy: s
7、heffieldun sheffieldun, na, Sun Oct 29 10:39:47 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 130200:1993 ii BSI 06-1999 National foreword This British Standard has been prepared under the direction of the Electronic Components Standards Policy Committee. It is the English language version of EN
8、130200:1993 Harmonized system of quality assessment for electronic components. Sectional specification: Fixed tantalum capacitors with non-solid or solid electrolyte, including amendment A3:1998 published by the Electronic Components Committee (CECC) of the European Committee for Electrotechnical St
9、andardization (CENELEC). Amendment A3 incorporates amendment A2. It supersedes BS CECC 30200:1986 which is withdrawn. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a
10、 British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, the EN title page, pages 2 to 24, an inside back cover and a back cover. This standard has been updated (see copyright date) and
11、 may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 10:39:47 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 130200 June 1993 + A3 March
12、1998 Supersedes CECC 30 200 Issue 2:1985 Descriptors: Quality, electronic components, capacitors English version Sectional Specification: Fixed Tantalum Capacitors with Non-Solid or Solid Electrolyte (includes amendment A3:1998) Spcification intermdiaire: Condensateurs fixes au tantale lectrolyte no
13、n solide ou solide (inclut lamendement A3:1998) Rahmenspezifikation: Tantal-Festkondensatoren mit festem oder flussigemElektrolyten (enthlt nderung A3:1998) This European Standard was approved by the CENELEC Electronic Components Committee (CECC) on 27 January 1992; amendment A3 was approved by CENE
14、LEC on 1994-10-16. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standar
15、ds may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notifi
16、ed to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and
17、United Kingdom. The membership of the CECC is identical, with the exception of the national electrotechnical committees of Greece, Iceland and Luxembourg. CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotec
18、hnische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels 1993 Copyright reserved to CENELEC members Ref. No. EN 130200:1993 + A3:1998 E Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 10:39:47 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 130200:1993 BSI 06-1999 2 Foreword The
19、 CENELEC Electronic Components Committee (CECC) is composed of those member countries of the European Committee for Electrotechnical Standardization (CENELEC) who wish to take part in a harmonized System for electronic components of assessed quality. Ths object of the System is to facilitate interna
20、tional trade by the harmonization of the specifications and quality assessment procedures for electronic components, and by the grant of an internationally recognized Mark, or Certificate of Conformity. The components produced under the System are thereby acceptable in all member countries without f
21、urther testing. This European Standard was prepared by CECC WG 3, Capacitors. The text of the draft based on document CECC 30 200 Issue 2:1985 was submitted to the formal vote for conversion to a European Standard: together with the voting report, circulated as document CECC (Secretariat) 2995 it wa
22、s approved by CECC as EN 130 200 on 27 January 1992. The text of EN 130 200 consists of: CECC 30 200 Issue 2 (with A1 to A6, A8 Erratum), CECC (Sec) 2523/01.90 RV CECC (Sec) 2995/12/91, CECC (Sec) 2874/09.91 RV CECC (Sec) 3088/04.92, The following dates were fixed: Foreword to amendment A3 This amen
23、dment to the European Standard EN 130200 was prepared by CLC/TC CECC/SC 40XA (former WG 3), Capacitors. The text of the draft based on document CECC (Secretariat) 3450 was submitted to the formal vote; together with the voting report, circulated as document CECC (Secretariat) 3550, it was approved a
24、s amendment A2 to EN 130200:1993 on 1994-05-15. The text of the draft based on document CECC (Secretariat) 3541 was submitted to the formal vote; together with the voting report, circulated as document CECC (Secretariat) 3620, it was approved as amendment A3 to EN 130200:1993 on 1994-10-16. This ame
25、ndment A3 includes amendment A2. The following dates were fixed: latest date of announcement of the EN at national level(doa) 1991-09-11 latest date of publication of an identical national standard(dop) 1992-03-11 latest date of declaration of national standards obsolescence1992-03-11 latest date of
26、 withdrawal of conflicting national standards(dow) 2001-09-11 latest date by which the amendment has to be implemented at national level by publication of an identical national standard or by endorsement(dop) 1998-10-01 latest date by which national standards conflicting with the amendment have to b
27、e withdrawn(dow) 1999-10-01 Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 10:39:47 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 130200:1993 BSI 06-19993 Contents Page Foreword 2 1 General5 1.1 Scope5 1.2 Related documents5 1.3 Information to be given in a detail specification5 1.4 Terminol
28、ogy6 1.5 Marking6 2 Preferred ratings and characteristics8 2.1 Preferred climatic categories8 2.2 Preferred values of ratings8 3 Quality assessment procedures9 3.1 Primary stage of manufacture9 3.2 Structurally similar components9 3.3 Certified test records of released lots9 3.4 Qualification approv
29、al9 3.5 Quality conformance inspection10 4 Test and measurement procedures11 4.1 Visual examination and check of dimensions11 4.2 Electrical tests11 4.3 Robustness of terminations12 4.4 Resistance to soldering heat13 4.5 Solderability14 4.6 Rapid change of temperature14 4.7 Vibration14 4.8 Bump14 4.
30、9 Shock15 4.10 Climatic sequence15 4.11 Damp heat, steady state16 4.12 Endurance16 4.13 Surge16 4.14 Reverse voltage17 4.15 Characteristics at high and low temperatures17 4.16 Component solvent resistance17 4.17 Solvent resistance of the marking17 4.18 High surge current test17 Annex A18 A.1Test pla
31、n for qualification approval assessment level E18 A.2Test plan for quality conformance inspection lot-by-lot tests Assessment level E19 Page A.3Test plan for quality conformance inspection periodic tests Assessment level E19 A.4Test schedule for qualification approval assessment level E20 Figure 113
32、 Table 114 Table 215 Table 317 Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 10:39:47 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 4 blank Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 10:39:47 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 130200:1993 BSI 06-19995 1 General 1.1 Scope
33、 This specification applies to polar and bipolar tantalum electrolytic capacitors with solid or non-solid electrolyte. It comprises capacitors for long-life applications and capacitors for general-purpose applications. Capacitors for special purpose application may need additonal requirements. Surfa
34、ce mounting styled capacitors are not covered. This specification covers three basic sub-families, namely: The object of this specification is to prescribe preferred ratings and characteristics and to select from the generic specification EN 130 000 the appropriate quality assessment procedures, tes
35、ts and measuring methods and to give general performance requirements for this type of capacitor. 1.2 Related documents ISO 3:1973, Preferred numbers Series of preferred numbers. IEC 62:1974, Marking codes for resistors and capacitors. IEC 63:1963, Preferred number series for resistors and capacitor
36、s. Amendment 1:1967 Amendment 2:1977. IEC 68, Basic environmental testing procedures. IEC 384-15:1982, Sectional specification: Fixed tantalum capacitors with non-solid or solid electrolyte. IEC 410:1973, Sampling plans and procedures for inspection by attributes. CECC 00 014:1986, CECC Assessed Pro
37、cess Average Procedure (APA). EN 130 000:1993, Generic specification: Fixed capacitors. 1.3 Information to be given in a detail specification Detail specifications shall be derived from the relevant blank detail specification. Detail specifications shall not specify requirements inferior to those of
38、 the generic, sectional or blank detail specification. When more severe requirements are included, they shall be listed in 1.9 of the detail specification and indicated in the test schedules, for example by an asterisk. The following information shall be given in each detail specification and the va
39、lues quoted shall preferably be selected from those given in the appropriate clause of this sectional specification. 1.3.1 Dimensions and outline drawing The detail specification shall give an illustration of the capacitor as an aid to easy recognition and for comparison of the capacitor with others
40、. Dimensions and their associated tolerances, which affect interchangeability and mounting, shall be given. All dimensions shall be stated in mm. NOTEThe information may be presented in tabular form. Normally the numerical values shall be given for the length, the width and height of the body and th
41、e wire spacing or for cylindrical types the body diameter, and the length and diameter of the terminations. When necessary, for example when a number of case sizes are covered by a detail specification, the dimensions and their associated tolerances shall be placed in a table below the drawing. When
42、 the configuration is other than described above, the detail specification shall state such dimensional information as will adequately describe the capacitor. When the capacitor is not designed for use on printed boards, this shall be clearly stated in the detail specification. Sub-family1 :Fixed no
43、n-solid electrolyte tantalum capacitors with foil electrode 1A:Plain foil electrode 1B:Etched foil electrode Sub-family2 :Fixed non-solid electrolyte tantalum capacitors with porous anode Sub-family3 :Fixed solid electrolyte tantalum capacitors with porous anode. Licensed Copy: sheffieldun sheffield
44、un, na, Sun Oct 29 10:39:47 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 130200:1993 6 BSI 06-1999 1.3.2 Mounting The detail specification shall specify the method of mounting to be applied for the application of the vibration and the bump or shock tests. The design of the capacitor may be such tha
45、t special mounting fixtures are required in its use. In this case the detail specification shall describe the mounting fixtures and they shall be used in the application of the vibration and bump or shock tests. NOTEIf recommendations for mounting for “normal” use are made, they shall be included in
46、 the detail specification under 1.8 “Additional information (not for inspection purposes)”. If they are included, a warning can be given that the full vibration, bump and shock performance may not be available if mounting methods other than those specified in 1.1 of the detail specification are used
47、. 1.3.3 Ratings and characteristics The ratings and characteristics shall be in accordance with the relevant clauses of this specification, together with the following: 1.3.3.1 Rated capacitance range See 2.2.1. NOTEWhen products approved to the detail specification have different ranges, the follow
48、ing statement should be added: “The range of capacitance values available in each voltage range is given in the Register of Approvals, CECC 00 200”. 1.3.3.2 Particular characteristics Additional characteristics may be listed, when they are considered necessary to specify adequately the component for
49、 design and application purposes. 1.3.3.3 Soldering The detail specification shall prescribe the test methods, severities and requirements applicable for the solderability test and the resistance to soldering heat test. 1.3.4 Marking The detail specification shall specify the content of the marking on the capacitor and on the package. Deviations from 1.5 of this sectional specification shall be specifically stated. 1.4 Terminology In addition to the applicable terms and definitions of EN 130 000 the following definitions apply: 1.4.1 Capaci