《BS-EN-2259-1995.pdf》由会员分享,可在线阅读,更多相关《BS-EN-2259-1995.pdf(12页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD AEROSPACE SERIES BS EN 2259:1995 Silicone rubber (VMQ) Hardness 50 IRHD The European Standard EN 2259:1995 has the status of a British Standard ICS 49.040.10 UDC 678.074:620.1:629.7 Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 01:20:03 GMT+00:00 2006, Uncontrolled Copy, (c
2、) BSI BS EN 2259:1995 This British Standard, having been prepared under the direction of the Engineering Sector Board, was published under the authority of the Standards Board and comes into effect on 15 November 1995 BSI 11-1999 The following BSI references relate to the work on this standard: Comm
3、ittee reference ACE/25 Draft for comment 94/714385 DC ISBN 0 580 24075 4 Committees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee ACE/25, Rubber and elastomeric materials for aerospace purposes, upon which the following bodies wer
4、e represented: British Adhesives and Sealants Association British Hydromechanics Research Group British Narrow Fabrics Association British Rubber Manufacturers Association Ltd. Ministry of Defence Society of British Aerospace Companies Limited Amendments issued since publication Amd. No.DateComments
5、 Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 01:20:03 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 2259:1995 BSI 11-1999i Contents Page Committees responsibleInside front cover National forewordii Foreword2 1Scope3 2Normative references3 3Application of the material3 4Properties3 5Des
6、ignation3 6Technical specification3 Table 1 Test methods4 Table 2 Tests after exposure to test media5 List of referencesInside back cover Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 01:20:03 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 2259:1995 ii BSI 11-1999 National foreword This B
7、ritish Standard has been prepared by Technical Committee ACE/25 and is the English language version of EN 2259:1995 Aerospace Series Silicone rubber (VMQ) Hardness 50 IRHD, published by the European Committee for Standardization (CEN). EN 2259 was produced as a result of international discussion in
8、which the United Kingdom took an active part. The European Standard EN 3207, referred to in clause 2, is in preparation and there is at present no corresponding British Standard. Preliminary copies of prEN 3207 are available from: BNAE, Technopolis 54, 199 rue Jean Jacques Rousseau, 92138 Issy les M
9、oulineaux Cedex, Paris, France. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Cross-ref
10、erences Publication referred toCorresponding British Standard ISO 1629:1987BS 3502 Symbols for plastics and rubber materials Part 2:1991 Schedule for symbols for rubbers ISO 1817:1985BS 903 Physical testing of rubber Part A16:1987 Determination of the effect of liquids Summary of pages This document
11、 comprises a front cover, an inside front cover, pages i and ii, the EN title page, pages 2 to 6, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cov
12、er. Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 01:20:03 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 2259 September 1995 ICS 49.040.10 Descriptors: Aircraft industry, rubber, silicones, hardness English version Aerospace series Silicone
13、rubber (VMQ) Hardness 50 IRHD Srie arospatiale lastomre silicone (VMQ) Duret 50 DIDC Luft- und Raumfahrt Silicon-Elastomer (VMQ) Hrte 50 IRHD This European Standard was approved by CEN on 1995-03-02. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the condit
14、ions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three o
15、fficial versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austri
16、a, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue
17、de Stassart 36, B-1050 Brussels 1995 All rights of reproduction and communication in any form and by any means reserved in all countries to CEN and its members Ref. No. EN 2259:1995 E Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 01:20:03 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 2259:1
18、995 BSI 11-1999 2 Foreword This European Standard has been prepared by the European Association of Aerospace Manufacturers (AECMA). After inquiries and votes carried out in accordance with the rules of this Association, this standard has successively received the approval of the National Association
19、s and the Official Services of the member countries of AECMA, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March 1996, and conflicting national standards shall
20、 be withdrawn at the latest by March 1996. According to the CEN/CENELEC Internal Regulations, the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain,
21、 Sweden, Switzerland, United Kingdom. Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 01:20:03 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 2259:1995 BSI 11-19993 1 Scope This standard specifies the properties of silicone rubber (VMQ)1), hardness 50 IRHD, for aerospace applications. 2 Normat
22、ive references This European Standard incorporates by dated or undated reference provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of an
23、y of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. ISO 1629, Rubber and latices Nomenclature. ISO 1817, Rubber, vulcanized Determination of the effect of liqu
24、ids. EN 3207, Aerospace series Rubber compounds Technical specification2). 3 Application of the material The suitability of the material for a specific application shall be determined by complementary tests carried out on the finished product as the properties specified in this standard are obtained
25、 from standard test specimens. 3.1 Typical use For application as ozone and weather resistant rubber with good thermal properties. NOTEThe ozone resistance test is not required. 3.2 Temperature range 4 Properties See Table 1 and Table 2. For qualification, all tests shall be performed. For batch acc
26、eptance, the tests identified in Table 1 and Table 2 shall be performed. 5 Designation 6 Technical specification EN 3207 1) Symbol as per ISO 1629 2) In preparation at the date of publication of this standard Continuous service:from 55 C to + 200 C Intermittent service :from 55 C to + 260 C Licensed
27、 Copy: sheffieldun sheffieldun, na, Fri Nov 03 01:20:03 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 2259:1995 4 BSI 11-1999 Table 1 Test methods LineColumn 123 PropertiesUnitsRequirements 1HardnessIRHD *) 2 3DensityMg/m31)*) 4 5Tensile strengthMPa5 min.*) 6 7Elongation at break%200 min.*) 8 9Modul
28、us at % strainMPa 10 11Tear strengthN/mm9 min. 12 13Resistance to low temperatures TR10C 40 max. 14CrystallizationPoint 15Compression set 15.1after70 h to 150 C % 35 max.*) 15.2after h to C 16 Ozone resistance 17 Ozone concentration Elongation of test piece Time Temperature : : : : ( ) pphm % h C 18
29、 Corrosion and adhesion on metals in a dry atmosphere 19Time Temperature : : h C 20Corrosion and adhesion on metals in a damp atmosphere 20.1Time Temperature Humidity : : : h C % 20.2Time Temperature Humidity : : : h C % 21 22 23 24 25 26 27 28 39 30 * Test for batch acceptance 1) The value determin
30、ed for each batch shall not differ from that determined at qualification by more than 0,02 Mg/m3. 50+ 5 4 Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 01:20:03 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 2259:1995 BSI 11-19995 Table 2 Tests after exposure to test media LineColumn 12345 1
31、Test mediaAirOil No. 1 see ISO 1817 Test fluid 101 see ISO 1817 2 Conditions of exposure in test media Units70 h/225 C70 h/150 C70 h/150 C 3 Permitted variation of the properties compared to the initial value Volume% a 4Mass% 5Tensile strength% 20 max. 25 max. 6 Elongation at break % 40 max. 20 max.
32、 7HardnessIRHD 8 a Test for batch acceptance + 10 0 + 40 0 + 10 10 0 10 Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 01:20:03 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 6 blank Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 01:20:03 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN
33、2259:1995 BSI 11-1999 List of references See national foreword. Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 01:20:03 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 2259:1995 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body r
34、esponsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest a
35、mendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can b
36、e found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards pub
37、lications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standard
38、s BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Ce
39、ntre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996
40、7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or tr
41、ansmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these deta
42、ils are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070. Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 01:20:03 GMT+00:00 2006, Uncontrolled Copy, (c) BSI