《BS-EN-15069-2008.pdf》由会员分享，可在线阅读，更多相关《BS-EN-15069-2008.pdf（70页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 15069:2008 Safety gas connection valves for metal hose assemblies used for the connection of domestic appliances using gaseous fuel ICS 23.060.40; 91.140.40 ? Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/
2、5910770001 Not for Resale, 08/14/2008 20:53:49 MDTNo reproduction or networking permitted without license from IHS -,-,- BS EN 15069:2008 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 April 2008 BSI 2008 ISBN 978 0 580 54780 5 National f
3、oreword This British Standard is the UK implementation of EN 15069:2008. The UK participation in its preparation was entrusted to Technical Committee GSE/1, Gas fittings and connections. A list of organizations represented on this committee can be obtained on request to its secretary. This publicati
4、on does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. Amendments/corrigenda issued since publication DateComments Copyright British Standards Inst
5、itution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 20:53:49 MDTNo reproduction or networking permitted without license from IHS -,-,- EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 15069 March 2008 ICS 23.060.40; 91.140.4
6、0 English Version Safety gas connection valves for metal hose assemblies used for the connection of domestic appliances using gaseous fuel Dispositifs de raccordement de scurit pour appareils usage domestique utilisant les combustibles gazeux et aliments par tuyau mtallique onduleux Sicherheitsgasan
7、schlussarmaturen fr den Anschluss von Gasgerten mit Gasschlauchleitungen in der Hausinstallation fr brennbare Gase This European Standard was approved by CEN on 2 February 2008. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this E
8、uropean Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (En
9、glish, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgar
10、ia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZ
11、ATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2008 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 15069:2008: E Copyright British Standards Institution Pr
12、ovided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 20:53:49 MDTNo reproduction or networking permitted without license from IHS -,-,- EN 15069:2008 (E) 2 Contents Page Foreword5 Introduction.6 1 Scope 6 2 Normative references6 3 Terms an
13、d definitions .7 4 General requirements9 4.1 SC valve types9 4.2 Classification10 4.2.1 Temperature classes.10 4.2.2 Pressure classes10 4.3 Construction requirements.10 4.3.1 General10 4.3.2 Materials .11 4.3.3 Nominal sizes.11 4.4 Construction.11 4.5 Connection.12 4.5.1 General12 4.5.2 Connection a
14、nd disconnection12 4.5.3 Disconnection12 4.5.4 Rotation 12 4.6 Operation12 4.6.1 General12 4.6.2 Manual operated control (if fitted).12 4.7 Dangerous substances .12 5 Performance requirements and tests13 5.1 General13 5.2 Test end fittings.13 5.3 Test sequence schedule .13 5.4 Leak-tightness15 5.4.1
15、 Angular seal .15 5.4.2 External leak-tightness .15 5.4.3 Internal leak-tightness.16 5.5 Internal Pressure16 5.5.1 Requirements.16 5.5.2 Test17 5.6 Rated flow rate.17 5.6.1 Requirements.17 5.6.2 Test17 5.7 Tensile strength resistance 19 5.7.1 Requirements.19 5.7.2 Tests19 5.8 Bending resistance20 5.
16、8.1 Requirements.20 5.8.2 Tests20 5.9 Resistance to torsion 20 5.9.1 Requirements.20 5.9.2 Tests20 5.10 Resistance to impact.21 5.10.1 Requirements.21 BS EN 15069:2008 Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not
17、 for Resale, 08/14/2008 20:53:49 MDTNo reproduction or networking permitted without license from IHS -,-,- EN 15069:2008 (E) 3 5.10.2 Tests .21 5.11 Durability22 5.11.1 Durability of the manually operated control SC valve.22 5.11.2 Durability of connection and disconnection 23 5.11.3 Rotation durabi
18、lity of the SC valve outlet.23 5.11.4 Temperature durability - Thermal ageing23 5.12 High and low temperature resistance .24 5.12.1 Low temperature resistance.24 5.12.2 High temperature resistance (only for SC valve without TSD).26 5.12.3 Leak-tightness during thermal load (only for SC valve with TS
19、D).26 5.13 Resistance to lubricants.26 5.13.1 General .26 5.13.2 Requirement.26 5.13.3 Test .26 5.14 Reaction to fire 27 5.14.1 Requirement.27 5.14.2 Testing and assessment methods.27 5.15 Resistance to gas27 5.15.1 General .27 5.15.2 Requirement.27 5.15.3 Test .27 5.16 Corrosion resistance.28 5.16.
20、1 Requirement.28 5.16.2 Test .28 5.17 Operating torque for a manually operated control SC valve28 5.17.1 Requirement.28 5.17.2 Test .28 5.18 Operating strength for a safety quick connection SC valve.29 5.18.1 Requirement.29 5.18.2 Test .29 5.19 Stop resistance29 5.19.1 Requirement.29 5.19.2 Test .30
21、 5.20 SC valves type 2 and 430 5.20.1 Leak-tightness of the OSD30 5.20.2 Overflow safety rate30 5.20.3 Overflow safety durability.31 5.20.4 Normal flow durability.31 5.21 Electrical continuity 32 5.21.1 Requirement.32 5.21.2 Test .32 5.22 Leak-tightness of the system with non-metal components32 5.22
22、.1 Requirement.32 5.22.2 Test .32 5.23 SC valves type 3 and 433 5.23.1 Reaction to temperature.33 6 Evaluation of conformity 33 6.1 General .33 6.2 Type testing .33 6.2.1 Initial type testing (ITT).33 6.2.2 Subsequent type testing.34 6.3 Factory production control (FPC)34 6.3.1 General .34 6.3.2 FPC
23、 requirements for all manufacturers.34 6.3.3 Manufacturer-specific FPC system requirements .36 6.4 Installation instructions37 6.5 Packaging.38 BS EN 15069:2008 Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Re
24、sale, 08/14/2008 20:53:49 MDTNo reproduction or networking permitted without license from IHS -,-,- EN 15069:2008 (E) 4 Annex A (informative) SC valve and hose fitting design requirements for connection to the gas supply pipework or to the pressure reduction device of portable gas bottles.39 Annex B
25、 (informative) Test end fitting 58 Annex ZA (informative) Clauses of this European Standard addressing the provision of the EU Construction Products Directive59 ZA.1 Scope and relevant characteristics .59 ZA.2 Procedure for attestation of conformity of SC valves .60 ZA.2.1 System of attestation of c
26、onformity 60 ZA.2.2 EC Certificate and Declaration of conformity.63 ZA.3 CE marking and labeling.64 Bibliography66 BS EN 15069:2008 Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 20:53:49 MDT
27、No reproduction or networking permitted without license from IHS -,-,- EN 15069:2008 (E) 5 Foreword This document (EN 15069:2008) has been prepared by Technical Committee CEN/TC 236 “Non industrial manually operated shut-off valves for gas and particular combinations valves-other products”, the secr
28、etariat of which is held by UNI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2008, and conflicting national standards shall be withdrawn at the latest by December 2009. Attention is
29、drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document has been prepared under a mandate given to CEN by the European Commission and the Eur
30、opean Free Trade Association, and supports essential requirements of EU Directive 89/106/EEC. For relationship with EU Directive 89/106/EEC, see informative Annex ZA, which is an integral part of this document. According to the CEN/CENELEC Internal Regulations, the national standards organizations o
31、f the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slo
32、vakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 15069:2008 Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 20:53:49 MDTNo reproduction or networking permitted without
33、 license from IHS -,-,- EN 15069:2008 (E) 6 Introduction This European Standard contains product characteristics relating to the safety of persons, animal and property and the protection of their environment. The objective of this European Standard is to achieve safe operation of connection valves b
34、y specifying the requirements of performance, materials and test methods. Safety gas connection valves are used internally to connect gas appliances including movable gas appliances and externally to connect appliances such as grills, gas radiation heating, lights etc. Valves manufactured to this Eu
35、ropean Standard are designed to be used with compatible hose assemblies conforming to EN 14800 and prEN 15070:2007. Attention is drawn to the need for careful quality control as given in EN ISO 9001:2000. This European Standard is based on a balance of requirements given by the major national Europe
36、an Gas Authorities for valves and metal hose assemblies for the connection of domestic gas appliances. It reflects the recognised practise and technology of products approved today as well as the present culture of usage by the consumer. The introduction of new technologies supported by National Gas
37、 Authorities may require the adoption of this European Standard regarding individual requirements and tests. 1 Scope These valves are suitable for connection of the fixed gas supply system to domestic appliances inside or outside a dwelling using 2nd or 3rd Family gases and at a pressure of up to an
38、d including 0,5 bar. These valves are designed for the use with either movable appliances or for the connection of fixed appliances. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies.
39、 For undated references, the latest edition of the referenced document (including any amendments) applies. EN 377, Lubricants for applications in appliances and associated controls using combustible gases except those designed for use in industrial processes EN 437:2003, Test gases Test pressures Ap
40、pliance categories EN 549, Rubber materials for seals and diaphragms for gas appliances and gas equipment EN 1503-1, Valves Materials for bodies, bonnets and covers Part 1: Steels specified in European Standards EN 1503-3, Valves Materials for bodies, bonnets and covers Part 3: Cast irons specified
41、in European Standards BS EN 15069:2008 Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 20:53:49 MDTNo reproduction or networking permitted without license from IHS -,-,- EN 15069:2008 (E) 7 EN
42、 1503-4, Valves Materials for bodies, bonnets and covers Part 4: Copper alloys specified in European Standards EN 1775:2007, Gas supply Gas pipework for buildings Maximum operating pressure less than or equal to 5 bar Functional recommendations EN 10222 (all parts), Steel forgings for pressure purpo
43、ses EN 10277-3, Bright steel products Technical delivery conditions Part 3: Free-cutting steels EN 13501-1:2007, Fire classification of construction products and building elements Part 1: Classification using data from reaction to fire tests EN 60335-1:2002, Household and similar electrical applianc
44、es Safety Part 1: General requirements (IEC 60335-1:2001, modified) EN ISO 9001:2000, Quality management systems Requirements (ISO 9001:2000) EN ISO 9227, Corrosion tests in artificial atmospheres Salt spray tests (ISO 9227:2006) EN ISO 11925-2, Reaction to fire tests Ignitability of building produc
45、ts subjected to direct impingement of flame Part 2: Single-flame source test (ISO 11925-2:2002) ISO 1817:2005, Rubber, vulcanized Determination of the effect of liquids 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 Connections 3.1.1 safety
46、connection valve component which permits or interrupts the flow of gas by the movement of a closure device which is operated by the connection or disconnection of a metal hose assembly where the valve inlet is connected to the gas installation pipework and whose outlet connects mechanically to the m
47、etal hose assembly and prevents any gas flow if the hose assembly is disconnected. In addition it can incorporate an overflow safety device or a thermal safety device. It also can be combined with a manually operated valve 3.1.2 safety quick connection end fitting consisting of two parts that is des
48、igned to permit quick connection and disconnection without tools, the device is leak-tight such that it prevents the release of gas from the upstream pipe work when disconnected and is designed to prevent accidental disconnection and incorrect operation 3.1.3 threaded connection connection which is gas tight achieved either by metal to metal contact in the thread or by assistance of a gasket. This conn