《BS-EN-13957-2008.pdf》由会员分享，可在线阅读，更多相关《BS-EN-13957-2008.pdf（20页珍藏版）》请在三一文库上搜索。
1、BS EN 13957:2008 ICS 77.150.10 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BRITISH STANDARD Aluminium and aluminium alloys Extruded round, coiled tube for general applications Specification Licensed Copy: London South Bank University, South Bank University, 16/11/2008 11:4
2、0, Uncontrolled Copy, (c) BSI This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 October 2008 BSI 2008 ISBN 978 0 580 56396 6 Amendments/corrigenda issued since publication DateComments BS EN 13957:2008 National foreword This British Standard
3、 is the UK implementation of EN 13957:2008. It supersedes BS EN 13957:2003 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee NFE/35, Light metals and their alloys. A list of organizations represented on this committee can be obtained on request to its s
4、ecretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. Licensed Copy: London South Bank University, South Bank University,
5、16/11/2008 11:40, Uncontrolled Copy, (c) BSI BS EN 13957:2008 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13957 October 2008 ICS 77.150.10Supersedes EN 13957:2003 English Version Aluminium and aluminium alloys - Extruded round, coiled tube for general applications - Specification Aluminium
6、et alliages daluminium - Tubes ronds fils, fournis en couronnes pour applications gnrales - Spcification Aluminium und Aluminiumlegierungen - Stranggepresste Rundrohre in Ringen fr allgemeine Anwendungen - Spezifikation This European Standard was approved by CEN on 6 September 2008. CEN members are
7、bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to th
8、e CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
9、status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Rom
10、ania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2008 CENAll rights of exploitation in any form and by any means reserve
11、d worldwide for CEN national Members. Ref. No. EN 13957:2008: E Licensed Copy: London South Bank University, South Bank University, 16/11/2008 11:40, Uncontrolled Copy, (c) BSI BS EN 13957:2008 EN 13957:2008 (E) 2 Contents Page Foreword3 1 Scope 4 2 Normative references4 3 Terms and definitions .4 4
12、 Ordering information.4 5 Requirements.6 5.1 Production and manufacturing processes .6 5.2 Quality control6 5.3 Chemical composition limits6 5.4 Mechanical properties.6 5.5 Surface quality.6 5.6 Coil characteristics7 5.7 Additional requirements .7 6 Tolerances on dimensions .8 6.1 General8 6.2 Diame
13、ter (outside and/or inside)8 6.3 Wall thickness and wall thickness variation (eccentricity) .9 6.4 Length.10 6.5 Squareness of cut ends 11 6.6 Cut end quality.11 7 Tolerances on form11 7.1 General11 7.2 Straightness.11 Annex A (informative) Wall thickness variation (eccentricity) .13 A.1 General13 A
14、.2 Specifying round tube sizes and tolerances 13 Bibliography17 Licensed Copy: London South Bank University, South Bank University, 16/11/2008 11:40, Uncontrolled Copy, (c) BSI BS EN 13957:2008 EN 13957:2008 (E) 3 Foreword This document (EN 13957:2008) has been prepared by Technical Committee CEN/TC
15、 132 “Aluminium and aluminium alloys”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2009, and conflicting national standards shall be withdrawn
16、at the latest by April 2009. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 13957:2003. Within its progra
17、mme of work, Technical Committee CEN/TC 132 entrusted CEN/TC 132/WG 5 “Extruded and drawn products“ to revise EN 13957:2003. The following editorial modifications have been introduced during the revision: the contents, text and tables have been changed to bring this European Standard in line with EN
18、 755. The following technical modifications have been introduced during the revision: Clause 1 has been amended to make clear the products covered by this European Standard and those which are not. In addition, the list of the most commonly used general engineering alloys is replaced by a reference
19、to the alloy group only. Clauses 3 and 4 including Tables: the text and the tables are updated. Annex A (informative) has been added to provide further explanation of wall thickness variation (eccentricity) along with some examples. Attention is drawn to the possibility that some of the elements of
20、this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. CEN/TC 132 affirms that it is its policy that in the case when a patentee refuses to grant licenses on standardised standard products under reasonable and not discrimin
21、atory conditions, then this product is removed from the corresponding standard. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmar
22、k, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Licensed Copy: London South Bank University, South Bank Univers
23、ity, 16/11/2008 11:40, Uncontrolled Copy, (c) BSI BS EN 13957:2008 EN 13957:2008 (E) 4 1 Scope This European Standard specifies the tolerances on dimensions and form of round aluminium and aluminium alloys porthole extruded tubes with an outside diameter (OD) of over 2 mm up to and including 50 mm s
24、upplied in coil form or in straight lengths cut from coiled material: see Figure 1. This European Standard mainly applies to round extruded tube for general engineering applications manufactured in 1xxx series of aluminium and 3xxx series of alloys. The use of this European Standard for non-standard
25、ised 1xxx aluminium and 3xxx alloys or alloys from other series, e.g. 5xxx or 6xxx, is subject to agreement between supplier and purchaser. This European Standard only applies to: round tube produced by the porthole/bridge method, extruded in coil form to the final dimensions required; tube as above
26、 but delivered in straight lengths cut from coiled material. This European Standard does not apply to: seamless extruded (die/mandrel method) tubes (EN 755-7); tubes extruded in straight lengths (i.e. not coiled) (EN 755-8). 2 Normative references The following referenced documents are indispensable
27、 for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 515, Aluminium and aluminium alloys Wrought products Temper designations EN 573-3, Aluminium and a
28、luminium alloys Chemical composition and form of wrought products Part 3: Chemical composition and form of products EN 755-2, Aluminium and aluminium alloys Extruded rod/bar, tube and profiles Part 2: Mechanical properties EN 12258-1:1998, Aluminium and aluminium alloys Terms and definitions Part 1:
29、 General terms 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 12258-1:1998 and the following apply. 3.1 order document document or set of documents agreed between supplier and purchaser at the time of ordering 4 Ordering information The order documen
30、t shall contain the following: a) form and type of product: Licensed Copy: London South Bank University, South Bank University, 16/11/2008 11:40, Uncontrolled Copy, (c) BSI BS EN 13957:2008 EN 13957:2008 (E) 5 the form of the product - porthole extruded tube in coil form or straight lengths, referen
31、ce to EN 573-3 for chemical composition limits, reference to EN 515 for temper designation, any special requirements identified by the purchaser; b) reference to EN 755-2 for mechanical property limits; c) reference to this document (EN 13957); d) dimensions of the tube: length (where appropriate),
32、and only two of the following dimensions: outside diameter, inside diameter, wall thickness; e) coil characteristics (where appropriate): inner coil diameter (often fixed/standardised), outer coil diameter, width/height of coil, coil weight limitations, drum/bobbin dimensions (where appropriate); f)
33、 quantity: mass, number of pieces, total length, tolerance on quantity; g) any requirements for inspection documents; h) any special requirements agreed between supplier and purchaser: marking of products, e.g. special identification, references to drawings, part numbers, etc., additional or special
34、 testing, surface finish requirements, Licensed Copy: London South Bank University, South Bank University, 16/11/2008 11:40, Uncontrolled Copy, (c) BSI BS EN 13957:2008 EN 13957:2008 (E) 6 surface protection, packaging, use of A50mm value instead of A value for elongation; i) where special requireme
35、nts are specified, this shall be stated on the order document with reference to the relevant European Standards. 5 Requirements 5.1 Production and manufacturing processes Unless otherwise specified in the order document, the production and manufacturing processes shall be left to the discretion of t
36、he manufacturer. Unless it is explicitly stated in the order document, no obligation shall be placed on the manufacturer to use the same processes for subsequent similar orders. 5.2 Quality control The supplier shall be responsible for the performance of all inspection and tests required by the rele
37、vant European Standard and/or the particular specification prior to shipment of the product. If the purchaser wishes to inspect the product at the manufacturers works, he shall notify the supplier at the time of placing the order. 5.3 Chemical composition limits The chemical composition limits shall
38、 be in conformity with the requirements specified in EN 573-3. If the purchaser requires closer limits for elements than those specified in EN 573-3, these limits shall be according to an agreement between supplier and purchaser and stated in the order document. 5.4 Mechanical properties The mechani
39、cal properties shall be in conformity with those specified in EN 755-2 or those agreed between supplier and purchaser and stated in the order document. Typical Brinell hardness (mainly used for flat surfaces, i.e. basically not suitable for round tubes/non-flat surfaces) values are given in EN 755-2
40、, but they are not binding for acceptance purposes. However, a Brinell hardness value may be agreed upon for acceptance testing. 5.5 Surface quality 5.5.1 Surface quality in general The surface shall be free from defects prejudicial to its suitable and proper use. The reference standard shall be agr
41、eed between supplier and purchaser. The product shall have a smooth and clean surface. However, small surface defects such as light scratches, indentations, discolouration and non-uniform surface appearance resulting from the manufacturing process (which cannot always be totally avoided) are general
42、ly permitted. Such surface quality is commonly referred to as “normal quality”. A greater degree of tolerance of surface defects (in respect to both the number and severity) is normally necessary for tube supplied in coil form compared to straight lengths, since it is not possible to remove individu
43、al defects within the coil. This issue should be taken into account by the purchaser when placing an order for coiled tube. Licensed Copy: London South Bank University, South Bank University, 16/11/2008 11:40, Uncontrolled Copy, (c) BSI BS EN 13957:2008 EN 13957:2008 (E) 7 5.5.2 Surface defects and
44、detection In the case of stricter and more specific requirements than “normal quality”, the following shall be subject to agreement between supplier and purchaser and stated in the order document: the testing/detection method (e.g. eddy current testing, pressure/leak testing etc.); the type (scratch
45、es, dents etc.) and size of defects; the method of marking the defects (e.g. ink, paint). 5.5.3 Surface lubrication A surface lubricant may be provided if required to: prevent the occurrence of fretting corrosion during transport; reduce the risk for surface defects created during subsequent manufac
46、turing processes (e.g. decoiling, straightening, cutting, tube manipulation etc.); improve the resistance to surface failures related to surface damage resulting from improper handling and/or storage (e.g. water stains, condensation etc.). As the type and amount of lubrication can have an impact on
47、the subsequent manufacturing process and the final application, the type and amount of lubricant shall be subject to agreement between supplier and purchaser and stated in the order document. 5.6 Coil characteristics 5.6.1 Coil dimensions The following coil dimensions shall be subject to agreement b
48、etween supplier and purchaser and stated in the order document: outside diameter, inside diameter and maximum width/height or weight of the coil; in the case of coils to be supplied on drums/bobbins, the dimensions of the drum/bobbin shall also be specified. 5.6.2 Type of coil winding The type of co
49、il winding (random or level winding) can be of importance to the subsequent manufacturing process (e.g. decoiling, straightening etc.) and shall, in such cases, be subject to agreement between supplier and purchaser and stated in the order document. 5.7 Additional requirements Any additional requirements shall be agreed between supplier and purchaser and stated on the order document. Licensed Copy: London South Bank University, South Bank University, 16/11/2008 11:40,