《BS-EN-1978-1998.pdf》由会员分享，可在线阅读，更多相关《BS-EN-1978-1998.pdf（12页珍藏版）》请在三一文库上搜索。
1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS EN 1978:1998 The Europ
2、ean Standard EN 1978:1998 has the status of a British Standard ICS 77.150.30 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Copper and copper alloys Copper cathodes Licensed Copy: sheffieldun sheffieldun, na, Mon Oct 30 05:13:07 GMT+00:00 2006, Uncontrolled Copy, (c) BSI This
3、 British Standard, having been prepared under the direction of the Engineering Sector Board, was published under the authority of the Standards Board and comes into effect on 15 August 1998 BSI 1998 ISBN 0 580 29726 8 BS EN 1978:1998 Amendments issued since publication Amd. No.DateText affected Nati
4、onal foreword This British Standard is the English language version of EN 1978:1998. Together with BS EN 1976:1998 it supersedes BS 6017:1981 which is withdrawn. The UK participation in its preparation was entrusted by Technical Committee NFE/34, Copper and copper alloys, to Subcommittee NFE/34/1, W
5、rought and unwrought copper and copper alloys, which has the responsibility to: aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and Euro
6、pean developments and promulgate them in the UK. A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI St
7、andards Catalogue under the section entitled International Standards Correspondence Index, or by using the Find facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible fo
8、r their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 9 and a back cover. Licensed Copy: sheffieldun sheffieldun, na, Mon
9、Oct 30 05:13:07 GMT+00:00 2006, Uncontrolled Copy, (c) BSI CEN European Committee for Standardization Comite Europe en de Normalisation Europa isches Komitee fu r Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1998 CEN All rights of exploitation in any form and by any means reserve
10、d worldwide for CEN national Members. Ref. No. EN 1978:1998 E EUROPEAN STANDARDEN 1978 NORME EUROPE ENNE EUROPA ISCHE NORM March 1998 ICS Descriptors: Copper, copper alloys, cathodes, designation, chemical composition, dimensions, electrical properties, sampling, tests, marking English version Coppe
11、r and copper alloys Copper cathodes Cuivre et alliages de cuivre Cathodes en cuivreKupfer und Kupferlegierungen Kupfer-Kathoden This European Standard was approved by CEN on 28 February 1998. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for
12、 giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official
13、versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgi
14、um, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. Licensed Copy: sheffieldun sheffieldun, na, Mon Oct 30 05:13:07 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Page 2 EN 1978:
15、1998 BSI 1998 Foreword This European Standard has been prepared by Technical Committee CEN/TC 133, Copper and copper alloys, the secretariat of which is held by DIN. Within its programme of work, Technical Committee CEN/TC 133 requested CEN/TC 133/WG 1, Unwrought copper products to prepare the follo
16、wing standard: EN 1978, Copper and copper alloys copper cathodes. This is one of a series of European Standards for products manufactured from refined copper grades. Other products are specified as follows: EN 1976, Copper and copper alloys Cast unwrought copper products. EN 1977, Copper and copper
17、alloys Copper drawing stock (wire rod). This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 1998, and conflicting national standards shall be withdrawn at the latest by September 1998. Accor
18、ding to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal
19、, Spain, Sweden, Switzerland and the United Kingdom. Contents Page Foreword2 Introduction3 1Scope3 2Normative references3 3Definitions3 3.1 cathode3 3.2 lot (copper cathodes)3 3.3 bundle3 3.4 sample cathodes3 3.5 cathode sample3 3.6 bulk sample3 3.7 analysis sample3 4Designations3 4.1 Material3 4.2
20、Product3 5Ordering information4 6Requirements4 6.1 Composition4 6.2 Electrical properties4 6.3 Dimensions and tolerances4 6.4 Surface condition4 7Sampling6 8Test methods6 8.1 Analysis6 8.2 Electrical resistivity6 8.3 Retests6 8.4 Rounding of results6 9Declaration of conformity and inspection documen
21、tation7 9.1 Declaration of conformity7 9.2 Inspection documentation7 10Marking10 Annex A (normative) Methods for use in cases of dispute, for the sampling of cathodes and for the preparation of analysis samples8 Annex B (informative) Information on electrical resistivity and conductivity relationshi
22、ps9 Annex C (informative) Bibliography9 Licensed Copy: sheffieldun sheffieldun, na, Mon Oct 30 05:13:07 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Page 3 EN 1978:1998 BSI 1998 Introduction This standard was prepared to combine the various requirements and methods of test for copper cathodes, previou
23、sly dealt with in a range of separate national standards. Copper cathodes are intended for melting. Cu-CATH-1 (CR001A) is primarily intended for the production of high conductivity copper, such as for drawing stock. Cu-CATH-2 (CR002A) is intended for the production of other wrought products for elec
24、trical and general purposes. 1 Scope This European Standard specifies the composition and property requirements for cathodes of two copper grades, designated Cu-CATH-1 (CR001A) and Cu-CATH-2 (CR002A). Annex A (normative) describes methods for sampling cathodes for use in cases of dispute between the
25、 purchaser and the supplier. Annex B (informative) gives information on the relationships between electrical resistivity and conductivity of copper. 2 Normative references This European Standard incorporates, by dated or undated reference, provisions from other publications. These normative referenc
26、es are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references, the la
27、test edition of the publication referred to applies. EN 1655, Copper and copper alloys Declarations of conformity. EN 10204, Metallic products Types of inspection documents. IEC 468, Method of measurement of resistivity of metallic materials. ISO 1553, Unalloyed copper containing not less than 99,90
28、 % of copper Determination of copper content Electrolytic method. NOTEInformative references to documents used in the preparation of this standard, and cited at the appropriate places in the text, are listed in a bibliography, see annex C. 3 Definitions For the purposes of this standard, the followi
29、ng definitions apply. 3.1 cathode flat, unwrought product made by electrolytic deposition 3.2 lot (copper cathodes) quantity of copper cathodes weighing over 25 t and up to and including 200 t, consisting of one consignment, or part of one consignment, produced by one refinery 3.3 bundle total amoun
30、t of a certain number of cathodes, typically 20 to 60, stacked together and secured, generally by steel bands 3.4 sample cathodes number of cathodes randomly selected from the lot, and considered in total to be representative of the lot 3.5 cathode sample portion of one of the sample cathodes (see 3
31、.4) obtained by systematic cutting of vertical strips 3.6 bulk sample sample produced by melting and casting into a suitable mould (or moulds) the cathode samples (see 3.5) obtained from all the sample cathodes and considered to be representative of the lot 3.7 analysis sample representative fractio
32、ns of swarf taken from the swarf arising from drilling, milling or sawing the bulk sample castings (see 3.6) 4 Designations 4.1 Material 4.1.1 General The material is designated either by symbol or number (see Table 1). 4.1.2 Symbol The material symbol designation is based upon the designation syste
33、m given in ISO 1190-1. 4.1.3 Number The material number designation is in accordance with the system given in EN 1412. 4.2 Product The product designation provides a standardized pattern of designation from which a rapid and unequivocal description of a product is conveyed in communication. It provi
34、des mutual comprehension at the international level with regard to products which meet the requirements of the relevant European Standard. Licensed Copy: sheffieldun sheffieldun, na, Mon Oct 30 05:13:07 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Page 4 EN 1978:1998 BSI 1998 The product designation i
35、s no substitute for the full content of the standard. The product designation for products to this standard shall consist of: denomination (Cathode); number of this European Standard (EN 1978); material designation, either symbol or number (see Table 1). The derivation of a product designation is sh
36、own in the following example. EXAMPLE Cathode conforming to this standard, in material designated either Cu-CATH-1 or CR001A, shall be designated as follows: Cathode or Cathode EN 1978 EN 1978 Cu-CATH-1 CR001A Denomination Number of this European Standard Material designation 5 Ordering information
37、In order to facilitate the enquiry, order and confirmation of order procedures between the purchaser and the supplier, the purchaser shall state on his enquiry and order the following information: a) quantity of product required (mass); b) denomination (Cathode); c) number of this European Standard
38、(EN 1978); d) material designation (see Table 1). NOTEIt is recommended that the product designation, as described in 4.2, is used for items b) to d). In addition, the purchaser shall also state on the enquiry and order any of the following, if required: e) the dimensions and tolerances required, if
39、 the cathodes are to be supplied cut to size (see 6.3); f) whether a declaration of conformity is required (see 9.1); g) whether an inspection document is required, and if so, which type (see 9.2). EXAMPLE Ordering details for 100 t of cathode conforming to EN 1978, in material designated either Cu-
40、CATH-1 or CR001A: 100 t Cathode EN 1978 Cu-CATH-1 or 100 t Cathode EN 1978 CR001A 6 Requirements 6.1 Composition The composition shall conform to the requirements for the appropriate grade given in Table 1. 6.2 Electrical properties The electrical properties shall conform to the requirements for the
41、 appropriate grade given in Table 2. The tests shall be carried out in accordance with 8.2. NOTEMass resistivity is the mandatory electrical property requirement in this standard. The relationship between mass resistivity and the corresponding volume resistivity and conductivity is given in annex B.
42、 6.3 Dimensions and tolerances The cathodes shall be either whole, or cut to sizes as agreed between the purchaser and the supplier and stated in the purchasers order see 5e). 6.4 Surface condition Cathodes shall withstand ordinary handling without breakage. They shall be reasonably free from nodule
43、s, outgrowth edges and from all extraneous materials such as electrolyte residues, dirt, grease and oil. Licensed Copy: sheffieldun sheffieldun, na, Mon Oct 30 05:13:07 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Page 5 EN 1978:1998 BSI 1998 Table 1 Composition of Cu-CATH-1 (CR001A) and Cu-CATH-2 (CR
44、002A) Material designation Composition % (m/m) ElementCuAgAsBiCdCoCrFeMnNiPPbSSbSeSiSnTeZnSum of elements listed in this table other than copper SymbolNumber Cu-CATH-1CR001Amin. max.0,00250,00051)0,000202)1)3)1)0,00103)1)3)1)0,00050,00154)0,00041)0,000202)3)3)0,000202)3)0,0065 Cu-CATH-2CR002Amin.99,
45、905) max.0,00050.0050,03 excluding Ag 1)(As + Cd + Cr + Mn + P + Sb) maximum 0,0015 %. 2) (Bi + Se + Te) maximum 0,000 3 %, of which (Se + Te) maximum 0,000 30 %. 3) (Co + Fe + Ni + Si + Sn + Zn) maximum 0,0020 %. 4) The sulfur content shall be determined on a cast sample. 5)Including silver up to a
46、 maximum of 0,015 %. Licensed Copy: sheffieldun sheffieldun, na, Mon Oct 30 05:13:07 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Page 6 EN 1978:1998 BSI 1998 Table 2 Electrical properties of Cu-CATH-1 (CR001A) and Cu-CATH-2 (CR002A) at 20 8C Material designationElectrical properties (see NOTE 1) Symb
47、olNumberMass resistivityNominal volume resistivity Nominal conductivity Vg/m2mVmMS/m% IACS max.max.min.min. Cu-CATH-1CR001A0,151 76(0,017 07)(58,58)(101,0) Cu-CATH-2CR002A0,153 28(0,017 24)(58,00)(100,0) NOTE 1Nominal values for volume resistivity and conductivity have been calculated from mass resi
48、stivity by methods described in annex B. NOTE 2Because of the inaccuracies involved in the calculations, these nominal values, which are given for guidance purposes, are enclosed in parentheses. NOTE 3For explanation of % IACS, see B.2. 7 Sampling For the routine sampling of cathodes for analysis, o
49、r for the routine determination of electrical properties, the method of sampling shall be at the discretion of the sampler. In cases of dispute concerning the composition, the cathodes shall be sampled and the analysis samples prepared in accordance with the procedure described in annex A. In cases of dispute concerning the electrical properties, unless otherwise agreed between the disputing parties (see NOTE), the cathodes shall be sampled in a