《BS-EN-1719-1999.pdf》由会员分享，可在线阅读，更多相关《BS-EN-1719-1999.pdf（10页珍藏版）》请在三一文库上搜索。
1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS EN 1719:1999 The Europ
2、ean Standard EN 1719:1998 has the status of a British Standard ICS 83.180 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Adhesives for paper and board, packaging and disposable sanitary products Tack measurement for pressure-sensitive adhesives Determination of loop tack Lice
3、nsed Copy: sheffieldun sheffieldun, na, Mon Oct 30 05:31:50 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 1719:1999 This British Standard, having been prepared under the direction of the Sector Committee for Materials and Chemicals, was published under the authority of the Standards Committee and
4、 comes into effect on 15 February 1999 BSI 02-1999 ISBN 0 580 30864 2 Amendments issued since publication Amd. No.DateText affected National foreword This British Standard is the English language version of EN 1719:1998. The UK participation in its preparation was entrusted to Technical Committee PR
5、I/52, Adhesives, which has the responsibility to: aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulga
6、te them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the secti
7、on entitled International Standards Correspondence Index, or by using the Find facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Comp
8、liance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 6, an inside back cover and a back cover. Licensed Copy: sheffieldun sheffieldun, na, Mon Oct 30 05:3
9、1:50 GMT+00:00 2006, Uncontrolled Copy, (c) BSI CEN European Committee for Standardization Comite Europe en de Normalisation Europa isches Komitee fu r Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1998 CEN All rights of exploitation in any form and by any means reserved worldwide
10、 for CEN national Members Ref. No. EN 1719:1998 E EUROPEAN STANDARDEN 1719 NORME EUROPE ENNE EUROPA ISCHE NORM September 1998 ICS 83.180 Descriptors: adhesives, tests, measurements, adhesive strength, loops, procedures English version Adhesives for paper and board, packaging and disposable sanitary
11、products Tack measurement for pressure-sensitive adhesives Determination of loop tack Adhe sifs pour papier et carton, emballages et produits sanitaires consommables Mesurage de ladhe sivite des produits autoadhe sifs De termination de ladhe sivite dune boucle Klebstoffe fu r Papier, Verpackung und
12、Hygieneprodukte Messung der Oberfla chenklebrigkeit von Haftklebstoffen Bestimmung der Oberfla chenklebrigkeit nach der Schlaufenmethode This European Standard was approved by CEN on 4 September 1998. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the condi
13、tions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three
14、official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austr
15、ia, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. Licensed Copy: sheffieldun sheffieldun, na, Mon Oct 30 05:31:50 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Page 2
16、 EN 1719:1998 BSI 02-1999 Foreword This European Standard has been prepared by Technical Committee CEN/TC 193, Adhesives, the Secretariat of which is held by AENOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement,
17、at the latest by March 1999, and conflicting national standards shall be withdrawn at the latest by March 1999. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Denmark,
18、 Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Contents Page Foreword2 1Scope3 2Normative references3 3Definition3 4Safety3 5Test method3 6Expression of results4 7Test report4 Licensed Copy: sh
19、effieldun sheffieldun, na, Mon Oct 30 05:31:50 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Page 3 EN 1719:1998 BSI 02-1999 1 Scope This European Standard specifies a test method for the determination of loop tack for coated pressure-sensitive adhesives. 2 Normative references This European Standard i
20、ncorporates, by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this
21、 European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN 923, Adhesives Terms and definitions. EN 1066, Adhesives Sampling. EN 1067, Adhesives Examination and preparation of samples for testing. 3 D
22、efinition For the purposes of this standard the definitions in accordance with EN 923 and the following definition apply. 3.1 loop tack the maximum force required to separate at a specified speed, a loop of adhesive coated material (adhesive outermost) which has been brought into contact with a spec
23、ified area of a defined surface 4 Safety Persons using this standard shall be familiar with normal laboratory practice. This standard does not purport to address all the safety problems, if any, associated with its use. It is the responsibility of the user to establish safety and health practices an
24、d to ensure compliance with any European and national regulatory conditions. 5 Test method 5.1 Test equipment 5.1.1 A tensile testing machine, with reversing facility and a vertical jaw separation rate of 5 mm/s with an accuracy of2 %. It shall also have a capability of measuring loads up to 100 N.
25、The measuring cell shall have an accuracy of2%. 5.1.2 A flat rigid plate, of glass or metal with a defined surface finish, of minimum dimensions 30 mm 3 30 mm 3 3,0 mm. The test plates shall be thoroughly cleaned. 5.1.3 A jig, to attach the plate in a horizontal position to the lower jaw of the tens
26、ile test machine. 5.1.4 Suitable equipment, for the preparation of an adhesives coating with a consistent dry coating weight of (252) g/m2(deviation from this coating weight shall be reported). 5.2 Materials 5.2.1 Adhesives, take the samples to be tested in accordance with EN 1066. Examine and prepa
27、re this sample for testing in accordance with EN 1067, 5.2.2 Polyester film, with a thickness of 50 mm. The use of any other substrate shall be reported. 5.2.3 Release paper. 5.3 Preparation and conditioning of test pieces Coat the adhesive sample onto the polyester film to produce a consistent dry
28、coating of (252) g/m2 (deviation of this coating weight shall be reported). Cover this coating with release paper. Coating and drying the adhesive shall conform to the appropriate practice. Test pieces are stripes taken from the coated polyester film and shall be (250,5) mm wide and have a length of
29、 (1752) mm in the machine direction. The cuts shall be clean and straight. A minimum of five strips shall be taken for each test. The strips shall be conditioned for (244) h before testing at standard climate of (232) 8C and (505) % r.h. Prior to use the cleaned plates shall be left for a minimum of
30、 30 min under the same conditions. Care shall be taken to handle clean plates by the edge only. Licensed Copy: sheffieldun sheffieldun, na, Mon Oct 30 05:31:50 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Page 4 EN 1719:1998 BSI 02-1999 5.4 Test procedure The test shall be performed at standard climat
31、e as described in 5.3. Remove the release paper from each strip immediately prior to the test being carried out. Hold the two ends of the adhesive coated strip and form the strip into a loop, adhesive surface outermost, by bringing the two ends together. Clamp the ends of the loop for a distance of
32、(101) mm into the top jaw of the tensile tester leaving the loop with a length of (1554) mm hanging freely. The sides of the jaw should be protected from the adhesive coating. Clamp the plate in the jig as described in 5.1.3 in the lower jaw (see Figure 1). Start the machine and bring the loop into
33、contact with the plate at a speed of 5 mm/s. When a contact area of 25 mm 3 25 mm approx. has been achieved, immediately reverse the direction of the machine and separate at a speed of 5 mm/s (see Figure 2). Record the maximum force (N) necessary to completely separate the loop from the plate. 6 Exp
34、ression of results The loop tack value is expressed as the average in newtons (N) of five strips tested. 7 Test report The test report shall include the following: a) reference to this European Standard; b) adhesive manufacturers name, grade and batch number of the other means of uniquely identifyin
35、g the adhesive sample; c) method of preparation of the adhesive coating; d) coating weight if other than (252) g/m2; e) specification of polyester film and release paper used; f) description of the surface of flat rigid plate used; g) loop tack value in newtons (N); h) lowest and highest test result
36、 in newton (N) found in test series; i) comments based on visual inspection such as adhesive transfer, lift of adhesive from substrate, etc.; j) date of test. Licensed Copy: sheffieldun sheffieldun, na, Mon Oct 30 05:31:50 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Page 5 EN 1719:1998 BSI 02-1999 Di
37、mensions in millimetres Figure 1 Test configuration at start Licensed Copy: sheffieldun sheffieldun, na, Mon Oct 30 05:31:50 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Page 6 EN 1719:1998 BSI 02-1999 Dimensions in millimetres Figure 2 Test configuration at reverse Licensed Copy: sheffieldun sheffiel
38、dun, na, Mon Oct 30 05:31:50 GMT+00:00 2006, Uncontrolled Copy, (c) BSI blank Licensed Copy: sheffieldun sheffieldun, na, Mon Oct 30 05:31:50 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
39、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It p
40、resents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of
41、 BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996
42、 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Servic
43、es. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on na
44、tional, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Su
45、bscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI pu
46、blications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic
47、, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than im
48、plementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070. Licensed Copy: sheffieldun sheffieldun, na, Mon Oct 30 05:31:50 GMT+00:00 2006, Uncontrolled Copy, (c) BSI