《BS-EN-2469-2007.pdf》由会员分享，可在线阅读，更多相关《BS-EN-2469-2007.pdf（10页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 2469:2007 Aerospace series Steel FE-PA3901 (X1CrNi18-10) Air melted Softened Wires 0,4 mm kk D kk 12,5 mm 450 MPa kk Rm kk 650 MPa The European Standard EN 2469:2007 has the status of a British Standard ICS 49.025.10 ? Licensed Copy: London South Bank University, London South
2、Bank University, Mon May 07 12:19:50 GMT+00:00 2007, Uncontrolled Copy, (c) BSI BS EN 2469:2007 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 April 2007 BSI 2007 ISBN 978 0 580 50552 2 National foreword This British Standard was publishe
3、d by BSI. It is the UK implementation of EN 2469:2007. The UK participation in its preparation was entrusted by Technical Committee ACE/61, Metallic materials for aerospace purposes, to Panel ACE/61/-/15, Steels. A list of organizations represented on ACE/61/-/15 can be obtained on request to its se
4、cretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. Amendments issued since publication Amd. No. DateComments Licensed Co
5、py: London South Bank University, London South Bank University, Mon May 07 12:19:50 GMT+00:00 2007, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 2469 March 2007 ICS 49.025.10 English Version Aerospace series - Steel FE-PA3901 (X1CrNi18-10) - Air melted - Softened -
6、 Wires - 0,4 mm D 12,5 mm - 450 MPa Rm 650 MPa Srie arospatiale - Acier FE-PA3901 (X1CrNi18-10) - labor lair - Tremp - Fils - 0,4 mm D 12,5 mm - 450 MPa Rm 650 MPa Luft- und Raumfahrt - Stahl FE-PA3901 (X1CrNi18-10) - Lufterschmolzen - Abgeschreckt - Drhte - 0,4 mm D 12,5 mm - 450 MPa Rm 650 MPa Thi
7、s European Standard was approved by CEN on 5 October 2006. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical referen
8、ces concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member in
9、to its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvi
10、a, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Bruss
11、els 2007 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 2469:2007: E Licensed Copy: London South Bank University, London South Bank University, Mon May 07 12:19:50 GMT+00:00 2007, Uncontrolled Copy, (c) BSI 2 Foreword This documen
12、t (EN 2469:2007) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official
13、 Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2007, and conflicting national standards shall be withdrawn at
14、 the latest by September 2007. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the
15、national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norw
16、ay, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. EN 2469:2007 Licensed Copy: London South Bank University, London South Bank University, Mon May 07 12:19:50 GMT+00:00 2007, Uncontrolled Copy, (c) BSI 3 Introduction This standard is part of the ser
17、ies of EN metallic material standards for aerospace applications. The general organization of this series is described in EN 4258. This standard has been prepared in accordance with EN 4500-5. 1 Scope This standard specifies the requirements relating to: Steel FE-PA3901 (X1CrNi18-10) Air melted Soft
18、ened Wires 0,4 mm D 12,5 mm 450 MPa Rm 650 MPa for aerospace applications. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referen
19、ced document (including any amendments) applies. EN 2002-6, Aerospace series Metallic materials Test methods Part 6: Bend testing. 1) EN 2043, Aerospace series Metallic materials General requirements for semi-finished product qualification (excluding forgings and castings). 1) EN 4258, Aerospace ser
20、ies Metallic materials General organization of standardization Links between types of EN standards and their use. EN 4500-5, Aerospace series Metallic materials Rules for drafting and presentation of material standards Part 5: Specific rules for steels. 1) EN 4700-4, Aerospace series Steel and heat
21、resisting alloys Wrought products Technical specification Part 4: Wire. 1) 1) Published as ASD Prestandard at the date of publication of this standard. EN 2469:2007 Licensed Copy: London South Bank University, London South Bank University, Mon May 07 12:19:50 GMT+00:00 2007, Uncontrolled Copy, (c) B
22、SI 4 1 Material designation Steel FE-PA3901 (X1CrNi18-10) Element C Si Mn P S Cr Ni Fe min. 17,0 9,0 2 Chemical composition % max. 0,030 1,00 2,00 0,035 0,025 19,0 12,0 Base 3 Method of melting Air melted 4.1 Form Wires 4.2 Method of production 4.3 Limit dimension(s) mm 0,4 D 12,5 5 Technical specif
23、ication EN 4700-4 Delivery condition Softened 6.1 Heat treatment 1 000 C 1 100 C / AC or WQ 6.2 Delivery condition code U Use condition Delivery condition 7 Heat treatment Characteristics 8.1 Test sample(s) EN 4700-4 8.2 Test piece(s) EN 4700-4 8.3 Heat treatment Softened 9 Dimensions concerned mm 0
24、,4 D 6 6 D 12,5 10 Thickness of cladding on each face % 11 Direction of test piece 12 Temperature C Ambient Ambient 13 Proof stress Rp0,2 MPa 180 180 14 Strength Rm MPa 450 Rm 650 450 Rm 650 15 Elongation A % 40 45 16 T Reduction of area Z % 17 Hardness 201 HB ; 212 HV a 201 HB ; 212 HV a 18 Shear s
25、trength Rc MPa 19 Bending k 20 Impact strength 21 Temperature C 22 Time h 23 Stress a MPa 24 Elongation a % 25 Rupture stress R MPa 26 C Elongation at rupture A % 27 Notes (see line 98) a EN 2469:2007 Licensed Copy: London South Bank University, London South Bank University, Mon May 07 12:19:50 GMT+
26、00:00 2007, Uncontrolled Copy, (c) BSI 5 1 EN 2002-6 2 One end of each coil 3 D 3 mm 37 Bending of wires (single bend test) 7 = 180 ; in contact 38 Corrosion (intergranular corrosion) See EN 4700-4. 95 Marking inspection See EN 4700-4. 96 Dimensional inspection See EN 4700-4. 98 Notes a HV for D 5 m
27、m 99 Typical use Austenitic corrosion resisting steel. EN 2469:2007 Licensed Copy: London South Bank University, London South Bank University, Mon May 07 12:19:50 GMT+00:00 2007, Uncontrolled Copy, (c) BSI 6 100 Product qualification See EN 2043. Qualification programme to be agreed between manufact
28、urer and purchaser. EN 2469:2007 Licensed Copy: London South Bank University, London South Bank University, Mon May 07 12:19:50 GMT+00:00 2007, Uncontrolled Copy, (c) BSI blank Licensed Copy: London South Bank University, London South Bank University, Mon May 07 12:19:50 GMT+00:00 2007, Uncontrolled
29、 Copy, (c) BSI BS EN 2469:2007 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Chart
30、er. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccura
31、cy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which e
32、nsures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also av
33、ailable from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information o
34、n national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)
35、20 8996 7048. Email: infobsi-. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 700
36、1. Email: membershipbsi-. Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the cop
37、yright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or other
38、wise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior writte
39、n permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-. Licensed Copy: London South Bank University, London South Bank University, Mon May 07 12:19:50 GMT+00:00 2007, Uncontrolled Copy, (c) BSI