BS-EN-15202-2006.pdf

《BS-EN-15202-2006.pdf》由会员分享，可在线阅读，更多相关《BS-EN-15202-2006.pdf（46页珍藏版）》请在三一文库上搜索。

1、BRITISH STANDARD BS EN 15202:2006 LPG equipment and accessories Essential operational dimensions for LPG cylinder valve outlet and associated equipment connections The European Standard EN 15202:2006 has the status of a British Standard ICS 23.060.40 ? Licensed Copy: London South Bank University, Lo

2、ndon South Bank University, Thu Jan 18 00:54:22 GMT+00:00 2007, Uncontrolled Copy, (c) BSI BS EN 15202:2006 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 January 2007 BSI 2007 ISBN 978-0-580-49916-6 National foreword This British Standar

3、d was published by BSI. It is the UK implementation of EN 15202:2006. The UK participation in its preparation was entrusted to Technical Committee PVE/19, LPG containers and their associated fittings. A list of organizations represented on PVE/19 can be obtained on request to its secretary. This pub

4、lication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. Amendments issued since publication Amd. No. DateComments Licensed Copy: London South

5、Bank University, London South Bank University, Thu Jan 18 00:54:22 GMT+00:00 2007, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 15202 December 2006 ICS 23.060.40 English Version LPG equipment and accessories - Essential operational dimensions for LPG cylinder valve

6、 outlet and associated equipment connections Equipements pour GPL et leurs accessoires - Dimensions oprationnelles essentielles des connexions des robinets et valves de bouteilles de GPL et des quipements associs Flssiggas-Gerte und Ausrstungsteile - Grundmae fr Ventilauslsse an Flssiggas-(LPG-)Flas

7、chen und zugehrige Verbindungen fr Gerte This European Standard was approved by CEN on 21 October 2006. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

8、 Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation

9、under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,

10、 Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: r

11、ue de Stassart, 36 B-1050 Brussels 2006 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 15202:2006: E Licensed Copy: London South Bank University, London South Bank University, Thu Jan 18 00:54:22 GMT+00:00 2007, Uncontrolled Copy,

12、(c) BSI EN 15202:2006 (E) 2 Contents Page Foreword3 1 Scope 4 2 Normative references4 3 Terms and definitions .5 4 Symbols and abbreviations5 5 Design.5 6 Connections in use38 7 Unsafe connections.38 8 Connecting torque.38 9 Marking.38 Annex A (informative) Connections by country.39 Annex B (informa

13、tive) Unsafe connections42 Bibliography43 Licensed Copy: London South Bank University, London South Bank University, Thu Jan 18 00:54:22 GMT+00:00 2007, Uncontrolled Copy, (c) BSI EN 15202:2006 (E) 3 Foreword This document (EN 15202:2006) has been prepared by Technical Committee CEN/TC 286 “Liquefie

14、d petroleum gas equipment and accessories”, the secretariat of which is held by NSAI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2007, and conflicting national standards shall be withdra

15、wn at the latest by June 2007. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard : Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Ice

16、land, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. Licensed Copy: London South Bank University, London South Bank University, Thu Jan 18 00:54:22 GMT+00:00 2007, Uncontrolled C

17、opy, (c) BSI EN 15202:2006 (E) 4 1 Scope This European Standard specifies basic dimensions of cylinder valves (manufactured in accordance with EN 13152 and EN 13153) and connectors (including regulators) to enable them to be connected together. This European Standard lists connections where it may b

18、e possible to connect together, but which when connected may not be sound or secure in some operating conditions or orientations. This European Standard also recommends tightening torques for the attachment of screwed metal-to-metal connections. This European Standard contains the drawings, which de

19、scribe direct cylinder valve connections in the following standards: EN 12864, EN 13785, and EN 13786. Quality assurance systems, production testing and particularly certificates of conformity are not covered in this standard. This European Standard excludes connections for automotive vehicles cover

20、ed by UN/ECE Regulation 67 and EN 13760 and excludes connections for cartridges. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the r

21、eferenced document (including any amendments) applies. EN 549, Rubber materials for seals and diaphragms for gas appliances and gas equipment EN 560, Gas welding equipment Hose connections for equipment for welding, cutting and allied processes EN ISO 228-1, Pipe threads where pressure-tight joints

22、are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000) ISO 68-1, ISO general purpose screw threads Basic profile Part 1: Metric screw threads ISO 3601-1, Fluid power systems - O-rings - Part 1: Inside diameters, cross-sections, tolerances and size identificatio

23、n code DIN 477-1, Gas cylinder valves rated for test pressures up to 300 bar; types, sizes, and outlets ANSI/CGA V-1 American National, Compressed Gas Association Standard for Compressed Gas Cylinder Valve Outlet and Inlet Connections ANSI/ASME/B1.5, ACME Screw Threads issued by American Society of

24、Mechanical Engineers 1990 Licensed Copy: London South Bank University, London South Bank University, Thu Jan 18 00:54:22 GMT+00:00 2007, Uncontrolled Copy, (c) BSI EN 15202:2006 (E) 5 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 LPG (lique

25、fied petroleum gas) mixture of predominantly butane or propane with traces of other hydrocarbon gases classified in accordance with UN number 1965, hydrocarbon gases mixture, liquefied, NOS or UN number 1075, petroleum gases, liquefied NOTE In some countries, UN numbers 1011 and 1978 may also be des

26、ignated LPG. 3.2 connector device that attaches to a cylinder valve to allow the passage of LPG to or from the cylinder 3.3 valve operating mechanism mechanism that opens the valve when, or after, a regulator or connector is fitted and closes the valve automatically when, or before, a regulator or c

27、onnector is disconnected 4 Symbols and abbreviations NBR Acrylonitrile-butadiene rubber (see ISO 4658). STP Standard Temperature and Pressure 15,6 C (288,7 K), 1,013 bar absolute (0,1013 MPa absolute) IRHD, International Rubber Hardness Degrees. 5 Design The dimensions shall be in accordance with th

28、ose given in the following figures. The travel distance of the valve operating mechanisms is identified where required. The drawings show the location of sealing elements where required. Any hexagon nut with a left hand thread shall, for easy identification, have notches (for example a 60 V groove)

29、at the corners. Where concentricity and surface finish are not specified, the requirements shall be as specified by the manufacturer. Licensed Copy: London South Bank University, London South Bank University, Thu Jan 18 00:54:22 GMT+00:00 2007, Uncontrolled Copy, (c) BSI EN 15202:2006 (E) 6 Dimensio

30、ns in millimetres Key Connector/Nut Seal Thread 1 nut A1 14,80 - 15 B1 16,8 - 17 T1 20 min. 2 connector A2 10,5 - 10,6 B2 10,2 - 10,4 T2 18,838 19,973 3 seal A3 17,4 - 17,5 B3 2,0 2,2 T3 17,696 18,266 4 valve A4 4,8 5,2 NBR or equivalent T4 1,814 5 nut thread A5 2,9 3,1 EN 549 A2/H3 T5 55 6 valve th

31、read A6 14 min. Valve T6 R 0,249 A7 20 x 1,814 L.H. C1 20 x 1,814 L.H. T7 19,589 19,98 A8 15,15 - 15,26 C2 14,3 14,7 T8 18,703 18,838 A9 2,9 3,1 C3 11,1 11,3 T9 17,317 17,676 A10 11 min. C4 6,8 - 7,2 A11 15,8 16,2 C5 R0,3 R0,7 A12 25 A/F C6 6,0 6,3 A13 8,4 max. C7 7,0 10,0 C8 11 min. C9 0,5 x 90 Fig

32、ure 1 Type G.1 - Threaded connection 20 x 1,814 LH - Spanner tightened Licensed Copy: London South Bank University, London South Bank University, Thu Jan 18 00:54:22 GMT+00:00 2007, Uncontrolled Copy, (c) BSI EN 15202:2006 (E) 7 Dimensions in millimetres Key Nut Connector Seal 1 nut A1 21,8 x 1,814

33、LH B1 18,5 18,7 C1 17,7 - 18,0 2 connector A2 16 max. B2 12,2 12,3 C2 10,7 - 11,0 3 seal A3 24,6 min. B3 11,1 11,3 C3 1,7 2,0 4 seal A4 7,5 min. B4 0,9 1,0 NBR or equivalent 5 valve A5 7,5 8,1 B5 2,0 2,2 EN 549 A2/H3 6 nut thread A6 9,9 10,5 B6 2,4 2,6 Thread 7 valve thread A7 12,5 min. B7 9,0 max.

34、T1 21,8 min. A8 5 wings equally spaced B8 A2 0,10,3 T2 20,622 20,722 Valve Seal T3 19,444 19,544 D1 21,7 x 1,814 LH E1 13,35 - 13,65 T4 1,814 D2 13 13,1 E2 8,0 - 8,4 T5 60 D3 7,8 8,0 E3 7,5 7,8 T6 R 0,249 D4 8,6 8,7 NBR or equivalent T7 21,6 21,7 EN 549 A2/H3 T8 20,422 20,522 T9 18,7 18,8 Figure 2 T

35、ype G.2 - Threaded connection 21,7 x 1,814 LH - 60 Hand tightened Licensed Copy: London South Bank University, London South Bank University, Thu Jan 18 00:54:22 GMT+00:00 2007, Uncontrolled Copy, (c) BSI EN 15202:2006 (E) 8 Dimensions in millimetres Key Connector Seal 1 connector A1 27 - 27,21 B1 25

36、,7 - 26,3 2 seal A2 13,9 - 14,1 B2 14,0 - 14,6 3 gasket A3 3,0 - 3,2 B3 1,35 1,65 4 valve A4 6,4 - 6,6 NBR or equivalent A5 13,7 - 13,9 EN 549 A2/H3 A6 M16 x 1,5-6g Valve 5 example of one configuration of the inlet/gas passage to the connector A7 1,6 1,8 D1 M16 x 1,5 6H A8 1,4 1,6 D2 8,4 8,6 A9 3,9

37、4,1 D3 26,5 27,3 A10 1,2 1,4 D4 1 x 45 A11 13,4 13,6 D5 10,3 10,5 Gasket D6 10,2 10,6 C1 7,5 0,15 D7 1,0 min. C2 17,0 0,1 C3 1,5 0,15 C4 4,0 0,15 Figure 3 Type G.3 - Threaded connection M16 x 1,5 R - Hand tightened Licensed Copy: London South Bank University, London South Bank University, Thu Jan 18

38、 00:54:22 GMT+00:00 2007, Uncontrolled Copy, (c) BSI EN 15202:2006 (E) 9 Dimensions in millimetres Key Connector/Nut Seal 1 nut A1 18,8 - 19,2 B1 19,8 - 19,2 2 connector A2 Ra 3,2 B2 11,6 - 12 3 seal A3 11,3 - 11,7 B3 1,9 2,1 4 valve A4 10,8 - 11,2 NBR or equivalent - EN 549 A2/H3 A5 11,89 - 12,0 or

39、 aluminium* or polyamide* * For guidance on the A6 1,7 1,9 Valve selection of aluminium, see A7 4,9 5,1 C1 W 21,8 x 1,814 LH DIN 477-1 EN ISO 11114-1 A8 5,9 6,1 C2 12,7 13,3 * For guidance on theA9 8 max.C36,8 7,2 selection of polyamide, see A10 30 A/F C4 9,0 min. EN ISO 11114-2 A11 16,15 - 16,26 C5

40、 Ra 3,2 A12 21,0 21,3 C6 11,5 min. A13 16,0 16,3 A14 W 21,8 x 1/1,814 LH DIN 477-1 A15 30,0 30,1 Figure 4 Type G.4 - Threaded connection W 21,8 x 1,814 LH - 55 Spanner tightened Licensed Copy: London South Bank University, London South Bank University, Thu Jan 18 00:54:22 GMT+00:00 2007, Uncontrolle

41、d Copy, (c) BSI EN 15202:2006 (E) 10 Dimensions in millimetres Key Connector/Nut Seal 1 nut A1 29,8 - 30 B1 18,8 - 19,2 2 connector A2 16,15 - 16,26 B2 6,9 - 6,95 3 seal A3 10,3 10,7 B3 1,9 2,1 4 valve A4 R 0,75 The seal material is polyamide*. A5 16,0 - 16,3 The Connector/Nut and seal also fits G12

42、 valve A6 21,0 21,3 Valve A7 W 21,8 x 1,814 LH DIN 477-1 C1 W 21,8 x 1,814 LH DIN 477-1 * For guidance on the selection of polyamide, see EN ISO 11114-2 A8 30 A/F C2 12,7 13,3 A9 15,84 - 15,96 C3 6,8 7,2 A10 17 min. C4 9,0 min. A11 3,9 4,1 C5 Ra 3,2 A12 6,8 7,2 C6 11,5 min. A13 18,8 19,2 C7 0,5 x 90

43、 A14 6,92 - 6,96 A15 3,9 - 4,1 A16 Ra 3,2 Figure 5 Type G.5 - Threaded connection W 21,8 x 1,814 LH 55 Spanner tightened Licensed Copy: London South Bank University, London South Bank University, Thu Jan 18 00:54:22 GMT+00:00 2007, Uncontrolled Copy, (c) BSI EN 15202:2006 (E) 11 Dimensions in millim

44、etres Key Connector Seal Valve 1 nut A1 15,8 - 16 B1 59 - 61 C1 W 22 x 1,155 LH 2 connector A2 11 - 11,2 B2 15 15,3 C2 15,5 - 15,7 3 seal A3 18,8 - 19 B3 10,8 11,2 C3 11,9 - 12,1 4 valve A4 2,9 3,1 B4 5,8 6,0 C4 59 - 61 A5 2,8 3,2 B5 8 + 3 deformation ribs C5 8,0 - 8,05 A6 6,3 6,7 B6 10,0 10,5 C6 11

45、 min. A7 W 22 x 1,155 LH B7 1,0 1,2 C7 1,2 1,4 A8 28,3 28,7 The seal material is polyamide*. C8 9 min. * For guidance on the selection of polyamide, see EN ISO 11114-2 A9 11,8 12,2 Figure 6 Type G.6 - Threaded connection W 22 x 1,155 LH Hand tightened Licensed Copy: London South Bank University, Lon

46、don South Bank University, Thu Jan 18 00:54:22 GMT+00:00 2007, Uncontrolled Copy, (c) BSI EN 15202:2006 (E) 12 Dimensions in millimetres Key Connector/Nut Valve 1 nut A1 Nom 13 - 16 (+0,1+0,37) C1 G 5/8 L.H EN ISO 228-1 2 connector A2 G 5/8 A LH EN ISO 228-1 C2 14 datum 3 valve A3 17 18 C3 11,5 max

47、WARNING A4 20,25 - 20,55 C4 59 - 61 Ra 0,8 A5 14,0 datum C5 20,35 20,65 G.9 type should not be fitted into the G.7 type as this may produce an unsafe connection. A6 R18,75 19,25 Ra 0,8 C6 17,75 18,25 A7 9,8 10,8 C7 14,3 min. A8 7,85 8,15 C8 37,75 A9 9,5 C9 R 0,5 - 1,0 A10 Nom. 13 - 16 (-0,1-0,37) A11 24 A/F . 28 A/F . 30,5 A/F A12 25 min. A13 12,5 min. A14 9 max. Figure 7 Type G.7 - Threaded connection G 5/8 LH Spanner tightened Licensed Copy: London South Bank University, London South Bank University, Thu Jan 18 00:54:22 GMT+00:00 2007, Uncontrolled