《BS-EN-2045-2001.pdf》由会员分享，可在线阅读，更多相关《BS-EN-2045-2001.pdf（10页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD AEROSPACE SERIES BS EN 2045:2001 Square bars, drawn, in aluminium and aluminium alloys Tolerance class h 11 Thickness 6 mm? a? 50 mm Dimensions The European Standard EN 2045:2001 has the status of a British Standard ICS 49.025.20; 49.035 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS P
2、ERMITTED BY COPYRIGHT LAW Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 01:30:27 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 2045:2001 This British Standard, having been prepared under the direction of the Engineering Sector Policy and Strategy Committee, was published under the author
3、ity of the Standards Policy and Strategy Committee on 24 December 2001 BSI 24 December 2001 ISBN 0 580 37991 4 National foreword This British Standard is the official English language version of EN 2045:2001. The UK participation in its preparation was entrusted to Technical Committee ACE/61, Inspec
4、tion and testing requirements for aerospace metallic materials, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred t
5、o in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contra
6、ct. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or prop
7、osals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 6, an inside back cover and a back cover. The BSI
8、copyright date displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. DateComments Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 01:30:27 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NOR
9、M EN 2045 December 2001 ICS 49.025.20 English version Aerospace series - Square bars, drawn in aluminuim and aluminium alloys - Tolerance class h 11 - Thickness 6 mm ? a ? 50 mm - Dimensions Srie arospatiale - Barres carres, tires en aluminium et alliages daluminium - Classe de tolrance h 11 - Epais
10、seurs 6 mm ? a ? 50 mm - Dimensions Luft- und Raumfahrt - Vierkantstangen, gezogen aus Aluminium und Aluminiumlegierungen - Toleranzklasse h 11 - Dicken 6 mm ? a ? 50 mm - Mae This European Standard was approved by CEN on 2 May 2001. CEN members are bound to comply with the CEN/CENELEC Internal Regu
11、lations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Management Centre or to any CEN member. This Eur
12、opean Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions. CEN members are the natio
13、nal standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KO
14、MITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2001 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 2045:2001 E Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 01:30:27 GMT+00:00 2006, Uncontrolled Co
15、py, (c) BSI EN 2045:2001 (E) 2 Foreword This European Standard has been prepared by the European Association of Aerospace Manufacturers (AECMA). After inquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Association
16、s and the Official Services of the member countries of AECMA, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2002, and conflicting national standards shall
17、be withdrawn at the latest by June 2002. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, It
18、aly, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 01:30:27 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 2045:2001 (E) 3 0 Introduction This standard is part of the series of EN metallic material
19、standards for aerospace applications. The general organization of this series is described in EN 4258. 1Scope This standard specifies the dimensions and tolerances of: Square bars, drawn in aluminium and aluminium alloys Tolerance class h 11 Thickness 6 mm ? a ? 50 mm for aerospace applications. 2No
20、rmative references This European Standard incorporates by dated or undated reference provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions o
21、f any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN 3848Aerospace series Semi-finished metallic products Method of measuring form deviations EN 4258Aero
22、space series Metallic materials General organization of standardization Links between types of EN standards and their use 3Form See figure 1. Figure 1 Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 01:30:27 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 2045:2001 (E) 4 4Recommended dimensions
23、 and mass 4.1Thickness and mass See table 1. Table 1 Nominal a mm Linear mass a kg/m 60,10 80,18 100,28 120,40 140,55 150,63 170,81 201,1 221,4 251,7 302,5 31,52,8 322,9 404,5 507,0 a For information, calculated with a density of 2,8 kg/dm3 4.2Length The order shall specify if bars are to be supplie
24、d in fixed or in random lengths. In the event of a supply of random lengths the minimum and maximum values for the lengths shall be specified on the order. 5Tolerances 5.1Dimensional tolerances 5.1.1Thickness See table 2. Table 2 Dimensions in millimetres ThicknessTolerance class 6 ? a ? 50h 11 Lice
25、nsed Copy: sheffieldun sheffieldun, na, Fri Nov 03 01:30:27 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 2045:2001 (E) 5 5.1.2Length See table 3, only applicable to bars supplied in fixed lengths. Table 3 Dimensions in millimetres LengthTolerances ? ? 6 000 ? 6 0 ? ? 6 000 ? 10 0 5.1.3Corner radii
26、See table 4. Table 4 Dimensions in millimetres ThicknessCorner radii r 6 ? a ? 10? 0,5 10 ? a ? 30? 0,8 30 ? a ? 50? 1,0 5.2Geometric tolerances 5.2.1Straightness 5.2.1.1Method of measurement and symbols See EN 3848. 5.2.1.2Tolerances See table 5. Table 5 Dimensions in millimetres Straightness devia
27、tion: Thickness Y1 per metreY2 on any length X2 a 6 ? a ? 50? 2? 0,6 a X2 ? 400 5.2.2Squareness 5.2.2.1Method of measurement and symbol See EN 3848. Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 01:30:27 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 2045:2001 (E) 6 5.2.2.2Tolerances See tab
28、le 6. Table 6 Dimensions in millimetres ThicknessSquareness deviation z 6 ? a ? 50? 0,005 ? a 5.2.3Twist 5.2.3.1Method of measurement and symbol See EN 3848. 5.2.3.2Tolerances See table 7. Table 7 Dimensions in millimetres Twist v: Thickness per metreon total length 6 ? a ? 30? 1,5? 3 30 ? a ? 50? 2
29、? 4 5.2.4Surface flatness 5.2.4.1Method of measurement See EN 3848. 5.2.4.2Tolerances The surface flatness tolerance shall be included in the thickness tolerances. Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 01:30:27 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Licensed Copy: sheffieldun sh
30、effieldun, na, Fri Nov 03 01:30:27 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 2045:2001 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe an
31、d at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products a
32、nd services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI of
33、fers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax
34、: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Info
35、rmation on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact
36、 the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Ad
37、ministration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-. Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Cop
38、yright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any fo
39、rm or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used
40、for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-. Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 01:30:27 GMT+00:00 2006, Uncontrolled Copy, (c) BSI