《BS-EN-2591-216-1998.pdf》由会员分享，可在线阅读，更多相关《BS-EN-2591-216-1998.pdf（8页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD AEROSPACE SERIES BS EN 2591-216:1998 Elements of electrical and optical connection Test methods Part 216: Engagement depth of contacts The European Standard EN 2591-216:1997 has the status of a British Standard ICS 49.060 Licensed Copy: sheffieldun sheffieldun, na, Thu Nov 02 18:01:
2、22 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 2591-216:1998 This British Standard, having been prepared under the direction of the Engineering Sector Board, was published under the authority of the Standards Board and comes into effect on 15 January 1998 BSI 04-1999 ISBN 0 580 29487 0 National
3、 foreword This British Standard is the English language version of EN 2591-216:1997. The UK participation in its preparation was entrusted by Technical Committee ACE/6, Aerospace avionic, electrical and fibre optic technology, to Subcommittee ACE/6/3, Aerospace connectors, which has the responsibili
4、ty to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of
5、organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references Attention is drawn to the fact that CEN and CENELEC Standards normally include an annex which lists normative references to international publications with their corresponding European public
6、ations. The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Cat
7、alogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document co
8、mprises a front cover, an inside front cover, pages i and ii, the EN title page, pages 2 and 3 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued si
9、nce publication Amd. No.DateComments Licensed Copy: sheffieldun sheffieldun, na, Thu Nov 02 18:01:22 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 2591-216:1998 BSI 04-1999i Contents Page National foreword Inside front cover Foreword2 Text of EN 2591-2163 Licensed Copy: sheffieldun sheffieldun, n
10、a, Thu Nov 02 18:01:22 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ii blank Licensed Copy: sheffieldun sheffieldun, na, Thu Nov 02 18:01:22 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 2591-216 October 1997 ICS 49.060 Descriptors: Aircraft industry,
11、aircraft equipment, connecting equipment, test English version Aerospace series Elements of electrical and optical connection Test methods Part 216: Engagement depth of contacts Srie arospatiale Organes de connexion lectrique et optique Mthodes dessais Partie 216: Profondeur denfichage des contacts
12、Luft- und Raumfahrt Elektrische und optische Verbindungselemente Prfverfahren Teil 216: Eindringtiefe der Kontakte This European Standard was approved by CEN on 22 June 1997. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this Euro
13、pean Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English
14、, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republi
15、c, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassa
16、rt 36, B-1050 Brussels 1997 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 2591-216:1997 E Licensed Copy: sheffieldun sheffieldun, na, Thu Nov 02 18:01:22 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 2591-216:1997 BSI 04-1999 2 F
17、oreword This European Standard has been prepared by the European Association of Aerospace Manufacturers (AECMA). After inquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of t
18、he member countries of AECMA, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 1998, and conflicting national standards shall be withdrawn at the latest by A
19、pril 1998. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands,
20、Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Contents Page Foreword2 1Scope3 2Normative references3 3Preparation of specimens3 4Method3 Figure 1 Test setup3 Licensed Copy: sheffieldun sheffieldun, na, Thu Nov 02 18:01:22 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 2591-216:
21、1997 BSI 04-19993 1 Scope This standard specifies a method of checking the depth of engagement of the male contact into the female contact. It shall be used together with EN 2591. 2 Normative references This European Standard incorporates by dated or undated reference provisions from other publicati
22、ons. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. F
23、or undated references the latest edition of the publication referred to applies. EN 2591, Aerospace series Elements of electrical and optical connection Test methods General. 3 Preparation of specimens 3.1 Specimens shall be wired and connected in series in accordance with Figure 1. 3.2 Unless speci
24、fied in the technical specification, the following details shall be stated: minimum depth of engagement of contacts; type of cable; requirement. 4 Method 4.1 Procedure Close the switch before coupling the specimens. Adjust the current to 100 mA. Open the switch. The specimens shall be slowly coupled
25、 using standard procedures. The zero point of travel is defined when the circuit closes. Continue with the coupling. The difference measured between the zero point and total coupling defines the depth of engagement of the male contact into the female contact. 4.2 Requirement The measured engagement
26、depth shall not be less than the specified value. Figure 1 Test setup Licensed Copy: sheffieldun sheffieldun, na, Thu Nov 02 18:01:22 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 2591-216:1998 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent natio
27、nal body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess th
28、e latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of w
29、hich can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign sta
30、ndards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information o
31、n standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Info
32、rmation Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax:
33、 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the internationalstandardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval sys
34、tem or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If t
35、hese details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070. Licensed Copy: sheffieldun sheffieldun, na, Thu Nov 02 18:01:22 GMT+00:00 2006, Uncontrolled Copy, (c) BSI