《BS-EN-2267-005-2006.pdf》由会员分享，可在线阅读，更多相关《BS-EN-2267-005-2006.pdf（12页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 2267-005:2006 Aerospace series Cables, electrical, for general purpose Operating temperatures between 55 C and 260 C Part 005: UV laser printable Product standard The European Standard EN 2267-005:2006 has the status of a British Standard ICS 49.060 ? Licensed Copy: sheffieldu
2、n sheffieldun, na, Fri Nov 03 01:13:07 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 2267-005:2006 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 October 2006 BSI 2006 ISBN 0 580 49471 3 National foreword This British Standard was publ
3、ished by BSI. It is the UK implementation of EN 2267-005:2006. The UK participation in its preparation was entrusted by Technical Committee ACE/6, Aerospace avionic electrical and fibre optic technology, to Subcommittee ACE/6/-/2, Aerospace Cables. A list of organizations represented on ACE/6/-/2 ca
4、n be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. Amendments issued since publication
5、 Amd. No. DateComments Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 01:13:07 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 2267-005 June 2006 ICS 49.060 English Version Aerospace series - Cables, electrical, for general purpose - Operating
6、temperatures between - 55 C and 260 C - Part 005: UV laser printable - Product standard Srie arospatiale - Cbles, lectriques, dusage gnral - Tempratures de fonctionnement comprises entre - 55 C et 260 C - Partie 005 : Marquables au laser UV - Norme de produit Luft- und Raumfahrt - Leitungen, elektri
7、sch, fr allgemeine Verwendung - Betriebstemperaturen zwischen - 55 C und 260 C - Teil 005: UV Laser bedruckbar - Produktnorm This European Standard was approved by CEN on 26 September 2005. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for g
8、iving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official ve
9、rsions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium
10、, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZAT
11、ION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2006 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 2267-005:2006: E Licensed Copy: sheffieldun sheffieldun, n
12、a, Fri Nov 03 01:13:07 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 2 Contents Page Foreword3 1 Scope4 2 Normative references4 3 Terms, definitions and symbols.4 4 Materials and construction.4 4.1 Materials .4 4.2 Construction.5 4.3 Number of cores 5 4.4 Colour coding of cores .6 5 Required characteri
13、stics.6 6 Quality assurance8 7 Designation 8 8 Identification and marking8 9 Packaging, labelling and delivery lengths8 10 Technical specification.8 EN 2267-005:2006 Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 01:13:07 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 3 Foreword This European St
14、andard (EN 2267-005:2006) has been prepared by the European Association of Aerospace Manufacturers - Standardization (AECMA-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Offi
15、cial Services of the member countries of AECMA, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2006, and conflicting national standards shall be withdra
16、wn at the latest by December 2006. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations,
17、the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Po
18、land, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. EN 2267-005:2006 Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 01:13:07 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 4 1 Scope This standard specifies the characteristics of UV laser printable elec
19、trical cables for use in the on-board electrical systems of aircraft at operating temperatures between 55 C and 260 C. It shall also be possible to mark these cables by hot stamp printing or ink jet printing. These markings shall be in accordance with EN 3838. 2 Normative references The following re
20、ferenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2083, Aerospace series Copper or copper alloy conductors for e
21、lectrical cables Product standard. EN 2084, Aerospace series Cables, electric, single-core, general purpose, with conductors in copper or copper alloy Technical specification. EN 2267-002, Aerospace series Cables, electrical, for general purpose Operating temperatures between 55 C and 260 C Part 002
22、: General. EN 3475-100*, Aerospace series Cables, electrical, aircraft use Test methods Part 100: General. EN 3838, Aerospace series Requirements and tests on user-applied markings on aircraft electrical cables.1) EN 9133, Aerospace series Quality management systems Qualification procedure for aeros
23、pace standard parts. 3 Terms, definitions and symbols For the purposes of this document, the terms, definitions and symbols given in EN 3475-100 apply. 4 Materials and construction 4.1 Materials Conductor: See EN 2267-002. Insulation: for conductor sizes code 001 to 010: first layer polyimide with t
24、otal thickness (nominal value) of 30 m, coated on both sides with a layer 2,5 m thick of fluorocarbon; * All parts quoted in this standard. 1) Published as AECMA Prestandard at the date of publication of this standard. EN 2267-005:2006 Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 01:13:07
25、GMT+00:00 2006, Uncontrolled Copy, (c) BSI 5 direction of winding immaterial overlap 51 % min.; second layer polytetrafluoroethylene (PTFE) 0,06 mm thick before use running in opposite direction to first layer overlap 65 % min.; or two layers of polytetrafluoroethylene (PTFE) 0,06 mm thick before us
26、e running in opposite direction to first layer one layer 51 % min. overlap and one layer in opposite direction 20 % min. overlap; for conductor sizes code 012 to 051: first layer polyimide with total thickness (nominal value) of 30 m, coated on both sides with a layer 2,5 m thick of fluorocarbon; di
27、rection of winding immaterial overlap 51 % min.; second layer polytetrafluoroethylene (PTFE) 0,06 mm thick before use running in opposite direction to first layer overlap 74 % min.; or two layers of polytetrafluoroethylene (PTFE) 0,06 mm thick before use running in opposite direction to first layer
28、one layer 51 % min. overlap and one layer in opposite direction 47 % min. overlap. A top coat may be applied. It shall be possible to mark the external surface of the insulation by UV laser printing. 4.2 Construction See EN 2083 and Table 1. Table 1 Nominal section AWG a Linear resistance at 20 C Ex
29、ternal diameter Mass mm2 /km mm kg/km Code for nominal section max. min. max. max. 001 0,15 26 160,0 0,90 1,06 2,8 002 0,25 24 114,0 0,99 1,16 3,6 004 0,4 22 60,0 1,15 1,31 5,0 006 0,6 20 33,2 1,38 1,56 7,9 010 1 18 21,1 1,62 1,82 11,4 012 1,2 16 14,5 1,97 2,18 16,5 020 2 14 10,9 2,22 2,43 21,5 030
30、3 12 6,8 2,68 2,93 33,5 050 5 10 4,2 3,27 3,46 52,4 051 b 5 10 4,1 3,30 3,58 53,9 a AWG = Closest American Wire Gage. b Flexible construction which may be used as an alternative. 4.3 Number of cores See EN 2267-002. EN 2267-005:2006 Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 01:13:07 GMT
31、+00:00 2006, Uncontrolled Copy, (c) BSI 6 4.4 Colour coding of cores See EN 2267-002. 5 Required characteristics According to EN 2084 and EN 3475-100. See Table 2. Table 2 EN 3475- Test Details 201 Visual examination Applicable 202 Mass Applicable; see Table 1. 203 Dimensions Applicable; see Table 1
32、. 301 Ohmic resistance per unit length Applicable; see Table 1. 302 Voltage proof test Applicable 303 Insulation resistance Applicable 304 Surface resistance Applicable 305 Overload resistance Applicable T1 = (310 5) C; T2 = (450 5) C 401 Accelerated ageing Applicable Temperature (310 5) C 402 Shrin
33、kage and delamination Applicable Temperature (290 5) C Maximum shrinkage at each end of cable: 0,15 mm2 to 0,6 mm2: 0,8 mm 1 mm2 to 1,2 mm2: 1 mm 2 mm2 to 5 mm2: 1,2 mm 403 Delamination and blocking Applicable Temperature (310 5) C 404 Thermal shock Applicable Temperature (290 5) C Maximum shrinkage
34、 at each end of cable: 0,15 mm2 to 0,6 mm2: 0,8 mm 1 mm2 to 1,2 mm2: 1 mm 2 mm2 to 5 mm2: 1,2 mm 405 Bending at ambient temperature Applicable 406 Cold bend test Applicable continued EN 2267-005:2006 Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 01:13:07 GMT+00:00 2006, Uncontrolled Copy, (
35、c) BSI 7 Table 2 (continued) EN 3475- Test Details 407 Flammability Applicable Extinguishing time: 3 s max. 408 Fire resistance Not applicable 409 Air-excluded ageing Not applicable 410 Thermal endurance Applicable 40 000 h (temperature 260 C) 411 Resistance to fluids Applicable 501 Dynamic cut-thro
36、ugh Applicable Temperatures (20 3) C and (260 5) C Cut-through force Nominal section mm2 20 C N 260 C N 0,15 0,25 0,40 0,60 1,00 1,20 2,00 3,00 5,00 70 85 110 140 140 150 150 165 180 15 30 45 55 70 85 95 105 120 502 Notch propagation Applicable Notch depth : 40 m 503 Scrape abrasion Applicable Test
37、force on needle for cables: 0,15 mm2 = 5 N 0,25 mm2 to 0,6 mm2 = 8 N 1 mm2 to 1,2 mm2 = 10 N 2 mm2 to 5 mm2 = 12 N 504 Torsion Applicable T3 = (260 5) C; T4 = (310 5) C 505 Tensile test on conductors and strands Applicable 506 Plating continuity Applicable 507 Adherence of plating Applicable 508 Pla
38、ting thickness Applicable 509 Solderability Not applicable 601 Smoke density Applicable 602 Toxicity Applicable continued EN 2267-005:2006 Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 01:13:07 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 8 Table 2 (concluded) EN 3475- Test Details 603 Resist
39、ance to wet arc tracking Not applicable 604 Resistance to dry arc propagation Not applicable 701 Strippability and adherence of insulation to the conductor Applicable 702 Screen pushback capability Not applicable 703 Permanence of manufacturers marking Applicable 6 Quality assurance See EN 9133. 7 D
40、esignation EXAMPLE Description block CABLE, ELECTRICAL Identity block EN2267-005A010P Number of this standard Code letter for number of cores (see EN 2267-002, Table 1) Code for nominal section (see Table 1) Code letter for colour coding of cores (see EN 2267-002) NOTE If necessary, the code I9005 s
41、hall be placed between the description block and the identity block. 8 Identification and marking See EN 2267-002. 9 Packaging, labelling and delivery lengths See EN 2084. 10 Technical specification See EN 2084. EN 2267-005:2006 Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 01:13:07 GMT+00:
42、00 2006, Uncontrolled Copy, (c) BSI blank Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 01:13:07 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 2267-005:2006 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for pre
43、paring British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editi
44、ons. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the ins
45、ide front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publicati
46、ons should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that
47、 have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are
48、also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-. Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- Further informat