《BS-EN-4499-2009.pdf》由会员分享，可在线阅读，更多相关《BS-EN-4499-2009.pdf（12页珍藏版）》请在三一文库上搜索。
1、BS EN 4499:2009 ICS 49.030.20 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BRITISH STANDARD Aerospace series Screws, 100 countersunk reduced head, offset cruciform recess, close tolerance normal shank, short thread, in titanium alloy, anodized, with aluminium pigmented coat
2、ing Classification: 1 100 MPa (at ambient temperature) / 315 C Licensed CopyChinese University of Hong Kong, 11/04/2009 07:37, Uncontrolled Copy, (c) BSI This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 March 2009 BSI 2009 ISBN 978 0 580 62
3、396 7 Amendments/corrigenda issued since publication DateComments BS EN 4499:2009 National foreword This British Standard is the UK implementation of EN 4499:2009. The UK participation in its preparation was entrusted to Technical Committee ACE/12, Aerospace fasteners and fastening systems. A list o
4、f organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal
5、obligations. Licensed CopyChinese University of Hong Kong, 11/04/2009 07:37, Uncontrolled Copy, (c) BSI BS EN 4499:2009 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 4499 February 2009 ICS 49.030.20 English Version Aerospace series - Screws, 100 countersunk reduced head, offset cruciform rece
6、ss, close tolerance normal shank, short thread, in titanium alloy, anodized, with aluminium pigmented coating - Classification: 1 100 MPa (at ambient temperature) / 315 C Srie arospatiale - Vis tte fraise 100 rduite, empreinte cruciforme dporte, ft normal tolrance serre, filetage court, en alliage d
7、e titane, anodises, avec revtement alumino-organique - Classification: 1 100 MPa ( temprature ambiante) / 315 C Luft- und Raumfahrt 100 Senk-Paschrauben, mit kleinem Kopf, mit Flgelkreuzschlitz, kurzes Gewinde, aus Titanlegierung, anodisiert,mit Aluminium pigmenttete Beschichtung - Klasse: 1 100 MPa
8、 (bei Raumtemperatur) / 315 C This European Standard was approved by CEN on 21 June 2008. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date li
9、sts and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the re
10、sponsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
11、 Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: A
12、venue Marnix 17, B-1000 Brussels 2009 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 4499:2009: E Licensed CopyChinese University of Hong Kong, 11/04/2009 07:37, Uncontrolled Copy, (c) BSI BS EN 4499:2009 EN 4499:2009 (E) 2 Conten
13、ts Page Foreword 3? 1?Scope 4? 2?Normative references 4? 3?Required characteristics .5? 3.1?Configuration - Dimensions - Masses .5? 3.2?Tolerances of form and position 5? 3.3?Materials .5? 3.4?Surface treatments 5? 4?Designation 8? 5?Marking .8? 6?Technical specification .9? 6.1?General 9? 6.2?Appro
14、val of manufacturers .9? 6.3?Qualification of bolts .9? 6.4?Requirement deleted .9? 7?Oversized bolts 9? Licensed CopyChinese University of Hong Kong, 11/04/2009 07:37, Uncontrolled Copy, (c) BSI BS EN 4499:2009 EN 4499:2009 (E) 3 Foreword This document (EN 4499:2009) has been prepared by the Aerosp
15、ace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior
16、to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by August 2009, and conflicting national standards shall be withdrawn at the latest by August 2009. Attention is drawn to t
17、he possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following coun
18、tries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spa
19、in, Sweden, Switzerland and the United Kingdom. Licensed CopyChinese University of Hong Kong, 11/04/2009 07:37, Uncontrolled Copy, (c) BSI BS EN 4499:2009 EN 4499:2009 (E) 4 1 Scope This standard specifies the characteristics of screws, 100 countersunk reduced head, offset cruciform recess, close to
20、lerance normal shank, short thread, in titanium alloy, anodized, with aluminium pigmented coating. Classification: 1 100 MPa 1) / 315 C 2). 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited a
21、pplies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2424, Aerospace series Aerospace series Marking of aerospace products EN 4016, Aerospace series Oversized bolts 3) EN 4473, Aerospace series Aluminium pigmented coatings Technical spe
22、cification 3) EN 4474, Aerospace series Aluminium pigmented coatings Coating methods 3) EN 9100, Aerospace series Quality management systems Requirements (based on ISO 9001:2000) and Quality systems Model for quality assurance in design, development, production, installation and servicing (based on
23、ISO 9001:1994) EN 9133, Aerospace series Quality management systems Qualification procedure for aerospace standard parts ISO 3353-1, Aerospace Lead and runout threads Part 1: Rolled external threads ISO 5855-2, Aerospace MJ threads Part 2: Limit dimensions for bolts and nuts ISO 7913, Aerospace Bolt
24、s and screws, metric Tolerances of form and position ISO 7994 4), Aerospace Internal drive, offset cruciform recess (Torq-Set ) for rotary fastening devices Metric series ISO 9152, Aerospace Bolts, with MJ threads, in titanium alloys, strength class 1 100 MPa Procurement specification ISO 13921, Aer
25、ospace Screws, 100 degrees reduced countersunk head, internal offset cruciform ribbed or unribbed drive, normal shank, short or medium length MJ threads, metallic material, coated or uncoated, strength classes less than or equal to 1 100 MPa Dimensions ISO 14275, Aerospace Drives, internal, offset c
26、ruciform, ribbed Metric series ISO 14277, Aerospace Drivers, ribbed, for internal offset cruciform ribbed or unribbed drives Metric series 1) Minimum tensile strength of the material at ambient temperature. 2) Maximum temperature that the screw can withstand without continuous change in its original
27、 characteristics, after return to ambient temperature. The maximum temperature is determined by the coating. 3) Published as ASD Prestandard at the date of publication of this standard. 4) Withdrawal, see ISO 14275, ISO 14277 and EN 14278. Licensed CopyChinese University of Hong Kong, 11/04/2009 07:
28、37, Uncontrolled Copy, (c) BSI BS EN 4499:2009 EN 4499:2009 (E) 5 ISO 14278, Aerospace Gauges, for internal offset cruciform ribbed or unribbed drives Metric series SAE AS87132, Lubricant, Cetyl Alcohol, 1-Hexadecanol, Application to Fasteners. 5) TR 3775, Aerospace series Bolts and pins Materials.
29、6) 3 Required characteristics 3.1 Configuration - Dimensions - Masses See Figure 1 and Table 1. Dimensions and tolerances are: in conformity with ISO 13921, expressed in millimetres and apply after coating (tolerance on shank diameter before coating is also specified). Details of form not stated are
30、 left to the manufacturers discretion. 3.2 Tolerances of form and position ISO 7913 3.3 Materials TR 3775 (titanium alloy, strength class 1 100 MPa). 3.4 Surface treatments EN 4473 and EN 4474 Lubrication with cetylic alcohol (chlorine free) according to SAE AS87132. 5) Published by: Society of Auto
31、motive Engineers Inc.(SAE), 400 Commonwealth Drive, Warrendale, PA 15096-0001 USA. 6) Published as ASD Technical Report at the date of publication of this standard. Licensed CopyChinese University of Hong Kong, 11/04/2009 07:37, Uncontrolled Copy, (c) BSI BS EN 4499:2009 EN 4499:2009 (E) 6 Values in
32、 micrometres apply prior to surface treatment. Break sharp edges 0,1 to 0,4. Key 1 One hole diameter D6 (optional) 2 Thread 3 Marking 4 Blended convex form permitted 5 Drive: see Table 3. 6 Conforms to ISO 3353-1 Figure 1 3,2 0,8 Licensed CopyChinese University of Hong Kong, 11/04/2009 07:37, Uncont
33、rolled Copy, (c) BSI BS EN 4499:2009 EN 4499:2009 (E) 7 Table 1 Diameter code Thread a D1 D2 D3 D4 D5 D6 E F G H L1 0,2 b c L2 L3 R Mass d Before coating After coating nom. Tol. max.min. nom.Tol. H13min. 0 0,08 max.Code nom. nom.Tol. e f 040 MJ40,7-4h6h 4 0,030 0,045 0,010 0,035 6,255,454,823 0 0,5
34、1,1 0,080,6 0,4 0,95003 to 040 3 to 407,55 0,4 0 0,2 0,24 0,05 050 MJ50,8-4h6h 5 7,8 6,8 5,793,4 0,5 1,5 0,1 0,85 0,5 1,18004 to 050 4 to 509 6 0,5 0,49 0,09 060 MJ61-4h6h 6 9,4 8,2 7,714,20,71 0,6 1,43005 to 060 5 to 6010 7 0,7 0,87 0,13 070 MJ71-4h6h 7 0,033 0,048 0,013 0,038 10,959,759 5,2 1,9 0,
35、82 1,67006 to 070 6 to 7011 1,43 0,17 080 MJ81-4h6h 8 12,5 11,3 10,286,20,93 1,9 006 to 080 6 to 80 11,57,51,96 0,22 100 MJ101,25-4h6h 10 15,6 14,4 12,867,9 2,4 1,15 2,36008 to 100 8 to 100 14,59 0,8 4,02 0,35 120 MJ121,25-4h6h 12 0,036 0,051 0,016 0,041 18,75 17,55 15,439,81,4 2,85010 to 120 10 to
36、12016 10 0,9 0 0,3 7,20 0,51 140 MJ141,5-4h6h 14 21,85 20,65 18 11,5 3 1,62 3,31010 to 140 10 to 14019 12 1,1 10,31 0,69 160 MJ161,5-4h6h 16 25 23,8 20,57 13,51,87 3,8 010 to 160 10 to 160 20,512,514,20 0,90 180 MJ181,5-4h6h 18 28,1 26,9 23,14 15,5 3,8 2,09 4,27011 to 180 11 to 180 22,514,5 1,3 19,9
37、7 1,14 200 MJ201,5-4h6h 20 0,040 0,055 0,020 0,045 31,2 30 25,71 17,52,32 4,74012 to 200 12 to 200 24,515 27,12 1,40 a In accordance with ISO 5855-2, except the thread major diameter “d max.“ which shall be equal to D1 min. 0,025. b Increments: 1 for L1 30 2 for 30 100 c If greater lengths are requi
38、red, they shall be chosen using the above increments. The length code corresponds to length L1, completed by one or two zeros to the left, where necessary, to obtain a three digit code. d Approximate values (kg/1 000 pieces), calculated on the basis of 4,45 kg/dm3, for information purposes only. The
39、y apply to screws without holes. e Value for first L4. f Increase for each additional millimetre of L4. Licensed CopyChinese University of Hong Kong, 11/04/2009 07:37, Uncontrolled Copy, (c) BSI BS EN 4499:2009 EN 4499:2009 (E) 8 4 Designation EXAMPLE Description block SCREW Identity block EN4499D05
40、0010A Number of this standard Hole code (see Table 2) Diameter code (see Table 1) Length code (see Table 1) Drive code (see Table 3) NOTE If necessary the code I9005 shall be placed between the description block and the identity block. Table 2 Holes Code With D Without (hyphen) Table 3 Drive Code IS
41、O 7994 R ISO 7994 unribbed A 5 Marking See Table 4 and Figure 1, indented. Table 4 Diameter code EN 2424 Style 040 N 050 to 200 C + MJ Licensed CopyChinese University of Hong Kong, 11/04/2009 07:37, Uncontrolled Copy, (c) BSI BS EN 4499:2009 EN 4499:2009 (E) 9 6 Technical specification 6.1 General I
42、SO 9152, with the following modifications: 6.2 Approval of manufacturers EN 9100 6.3 Qualification of bolts EN 9133 6.4 Requirement deleted Double shear strength 7 Oversized bolts EN 4016 Licensed CopyChinese University of Hong Kong, 11/04/2009 07:37, Uncontrolled Copy, (c) BSI BS EN 4499:2009 BSI G
43、roup Headquarters 389 Chiswick High Road, London, W4 4AL, UK Tel +44 (0)20 8996 9001 Fax +44 (0)20 8996 7001 standards BSI - British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the inte
44、rnational level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services.
45、We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members
46、an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8
47、996 7001 Email: You may also buy directly using a debit/credit card from the BSI Shop on the Website http:/ In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Inform
48、ation on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact I
49、nformation Centre. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002 Fa