《BS-EN-500-5-1996.pdf》由会员分享，可在线阅读，更多相关《BS-EN-500-5-1996.pdf（10页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 500-5:1996 Mobile road construction machinery Safety Part 5: Specific requirements for joint cutters The European Standard EN 500-5:1995 has the status of a British Standard ICS 91.220 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 06 09:42:41 GMT+00:00 2006, Uncontrolled
2、 Copy, (c) BSI BS EN 500-5:1996 This British Standard, having been prepared under the direction of the Sector Board for Engineering, was published under the authority of the Standards Board and comes into effect on 15 June 1996 BSI 08-1999 The following BSI references relate to the work on this stan
3、dard: Committee reference B/513/1 Draft for comment 91/14882 DC ISBN 0 580 25396 1 Committees responsible for this British Standard The preparation of this British Standard was entrusted by Technical Committee B/513, Construction equipment and plant, and site safety, to Subcommittee B/513/1, Earth-m
4、oving machinery, upon which the following bodies were represented: British Coal Corporation Construction Plant-hire Association Federation of Civil Engineering Contractors Federation of Manufacturers of Construction Equipment and Cranes Health and Safety Executive Institution of Civil Engineers Sils
5、oe Research Institute Amendments issued since publication Amd. No.DateComments Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 06 09:42:41 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 500-5:1996 BSI 08-1999i Contents Page Committees responsibleInside front cover National forewordii Foreword2
6、 Text of EN 500-53 List of referencesInside back cover Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 06 09:42:41 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 500-5:1996 ii BSI 08-1999 National foreword This British Standard has been prepared by Subcommittee B/513/1 and is the English langu
7、age version of EN 500-5:1995 Mobile road construction machinery Safety Part 5: Specific requirements for joint cutters, published by the European Committee for Standardization (CEN).It is one of a number of British Standards implementing European Standards on machinery safety matters, in the develop
8、ment of which the United Kingdom has played an active part. This British Standard covers the essential safety requirements in the Machinery Directive (89/392/EEC) and the Amending Directive (91/368/EEC). A British Standard does not purport to include all the necessary provisions of a contract. Users
9、 of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Cross-reference Publication referred toCorresponding British Standard BS EN 500 Mobile road construction machinery Safety EN 500-1:1995Pa
10、rt 1:1996 Common requirements Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, the EN title page, pages 2 to 4, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will
11、 be indicated in the amendment table on the inside front cover. Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 06 09:42:41 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 500-5 September 1995 ICS 91.220 Descriptors: Roads, construction, site equip
12、ment, mobile equipment, cutting, joints, safety, specifications, accident prevention, hazards, safety measures, safety devices, signalling English version Mobile road construction machinery Safety Part 5: Specific requirements for joint cutters Machines mobiles pour la construction de routes Scurit
13、Partie 5: Exigences spcifiques pour dcoupeurs de joints Bewegliche Straenbaumaschinen Sicherheit Teil 5: Besondere Anforderungen an Fugenschneider This European Standard was approved by CEN on 1954-06-29. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the c
14、onditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in th
15、ree official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of A
16、ustria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat:
17、 rue de Stassart 36, B-1050 Brussels 1995 All rights of reproduction and communication in any form and by any means reserved in all countries to CEN and its members. Ref. No. EN 500-5:1995 E Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 06 09:42:41 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN
18、 500-5:1995 BSI 08-1999 2 Foreword This European Standard was prepared by the Technical Committee CEN/TC 151, Construction equipment and building material machines Safety, of which the secretariat is held by DIN. This European Standard has been prepared under a mandate given to CEN by the European C
19、ommission and the European Free Trade Association, and supports essential requirements of EC Directive(s). EN 500 Mobile road construction machinery Safety comprises the following parts: Part 1: Common requirements; Part 2: Specific requirements for road-milling machines; Part 3: Specific requiremen
20、ts for soil stabilization machines; Part 4: Specific requirements for compaction machines; Part 5: Specific requirements for joint cutters; Part 6: Specific requirements for paver-finishers. This European Standard shall be given the status of a national standard, either by publication of an identica
21、l text or by endorsement, at the latest by March 1996, and conflicting national standards shall be withdrawn at the latest by March 1996. In accordance with the CEN/CENELEC Internal Regulations, the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland
22、, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, United Kingdom. Contents Page Foreword2 0Introduction3 1Scope3 2Normative references3 3Definitions3 4List of hazards3 5Safety requirements3 5.1Lighting3 5.2Design of the machine
23、 in relation to its operation and handling3 5.3Operators station3 5.4Operators seat3 5.5Controls3 5.6Starting3 5.7Stopping3 5.8Danger of falling off, access to operators station and to service points3 5.9Precautions against hazards caused by moving parts3 5.10 Hazards caused by dust emission3 5.11 F
24、ire protection3 5.12 Hazards due to extreme temperatures3 5.13 Signal devices and warning signs3 6Instruction handbook4 7Marking4 8Verification of safety requirements/measures4 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 06 09:42:41 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 500-5:1995 BS
25、I 08-19993 0 Introduction This Part of EN 500 contains additional requirements to EN 500-1:1995 Common requirements. The clauses of this standard have the same numbering as those of EN 500-1:1995. 1 Scope This Part of EN 500 specifies the safety requirements for joint cutters as defined in clause 3
26、and deals with the significant hazards pertinent to joint cutters, when used as intended and in conditions foreseen by the manufacturer. 2 Normative references This European Standard incorporates by dated or undated references, provisions from other publications. These normative references are cited
27、 at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition
28、of the publication referred to applies. EN 500-1:1995, Mobile road construction machinery Safety Part 1: Common requirements. 3 Definitions For the purposes of this standard the following definition applies. joint cutters mobile machines intended for the production of joints in concrete, asphalt and
29、 similar road surfaces. The cutting tool is a rotating high speed disc. The forward motion of the joint cutters can be: manual; manual with mechanical assistance; power driven. 4 List of hazards See EN 500-1:1995. 5 Safety requirements 5.1 Lighting See EN 500-1:1995. 5.2 Design of the machine in rel
30、ation to its operation and handling See EN 500-1:1995. 5.3 Operators station See EN 500-1:1995. 5.4 Operators seat See EN 500-1:1995. 5.5 Controls See EN 500-1:1995. 5.6 Starting Self propelled joint cutters shall be equipped with a device which makes it possible to disengage the drive system from t
31、he cutting tool. 5.7 Stopping Joint cutters shall be fitted with a stopping device, e.g. a parking brake to avoid unintentional movement of the machine. NOTE 1In the case of joint cutters with a service weight less than 100 kg, such a parking brake is not required. NOTE 2Hold-to-run control for the
32、travel function is not required for joint cutters. 5.8 Danger of falling off, access to operators station and to service points See EN 500-1:1995. 5.9 Precautions against hazards caused by moving parts Guards for cutting tools shall be constructed with appropriate materials and shall cover the upper
33、 half of the tool in all directions. The guards shall also be strong enough to stop parts of the tools which could possibly be ejected. Adequate guards are, for example, made of steel, which shall be at least 3 mm thick in the cutting plane of the tool. The guards shall also cover tightening flanges
34、 for the tools (high speed discs). 5.10 Hazards caused by dust emission Joint cutters shall be equipped with a water sprinkler arrangement for wet cutting. The flow of water supplied to the cutting tool shall ensure dust-free operation. 5.11 Fire protection See EN 500-1:1995. 5.12 Hazards due to ext
35、reme temperatures See EN 500-1:1995. 5.13 Signal devices and warning signs The direction of rotation of the cutting tool shall be clearly and permanently marked with an arrow on the guards. Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 06 09:42:41 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN
36、500-5:1995 4 BSI 08-1999 6 Instruction handbook See EN 500-1:1995. 7 Marking See EN 500-1:1995. 8 Verification of safety requirements/measures See EN 500-1:1995. Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 06 09:42:41 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 500-5:1996 BSI 08-1999 Li
37、st of references See national foreword. Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 06 09:42:41 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 500-5:1996 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparin
38、g British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.
39、It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside f
40、ront cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be add
41、ressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide r
42、ange of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 711
43、1. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyrig
44、ht subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form o
45、r by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for
46、any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070. Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 06 09:42:41 GMT+00:00 2006, Uncontrolled Copy, (c) BSI