《BS-EN-60927-2007.pdf》由会员分享，可在线阅读，更多相关《BS-EN-60927-2007.pdf（34页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 60927:2007 Incorporating corrigendum August 2008 Auxiliaries for lamps Starting devices (other than glow starters) Performance requirements ICS 29.140.30 ? Licensed Copy: London South Bank University, South Bank University, 31/01/2009 04:01, Uncontrolled Copy, (c) BSI BS EN 60
2、927:2007 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 November 2007 BSI 2008 ISBN 978 0 580 64305 7 National foreword This British Standard is the UK implementation of EN 60927:2007, The UK participation in its preparation was entrusted
3、 by Technical Committee CPL/34, Lamps and related equipment, to Subcommittee CPL/34/3, Auxiliaries for lamps. request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a Britis
4、h Standard cannot confer immunity from legal obligations. Amendments/corrigenda issued since publication DateComments Implementation of CENELEC corrigendum August 2008. CENELEC foreword and Annex ZA updated It supersedes BS EN 60927:1997, which will be withdrawn on 1 October 2011. incorporating corr
5、igendum August 2008. It is identical with IEC 60927:2007. A list of organizations represented on this subcommittee can be obtained on 31 December 2008 Licensed Copy: London South Bank University, South Bank University, 31/01/2009 04:01, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD EN 60927 NORME EUR
6、OPENNE EUROPISCHE NORM October 2007 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2007 CENELEC - All rights of exploitation in
7、 any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60927:2007 E ICS 29.140.30 Supersedes EN 60927:1996 + A1:1999 + A2:2004 English version Auxiliaries for lamps - Starting devices (other than glow starters) - Performance requirements (IEC 60927:2007) Appareils auxiliaires
8、 pour lampes - Dispositifs damorage (autres que starters lueur) - Exigences de performance (CEI 60927:2007) Gerte fr Lampen - Startgerte (andere als Glimmstarter) - Anforderungen an die Arbeitsweise (IEC 60927:2007) This European Standard was approved by CENELEC on 2007-09-11. CENELEC members are bo
9、und to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the
10、Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the sam
11、e status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norw
12、ay, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Incorporating corrigendum August 2008 Licensed Copy: London South Bank University, South Bank University, 31/01/2009 04:01, Uncontrolled Copy, (c) BSI Foreword The text of document 34C/783/FDIS, fut
13、ure edition 3 of IEC 60927, prepared by SC 34C, Auxiliaries for lamps, of IEC TC 34, Lamps and related equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60927 on 2007-09-11. This European Standard supersedes EN 60927:1996 + A1:1999 + A2:2004. Subclause 4.5 h
14、as been inserted in order to install an obligatory link to the relevant lamp standard. This standard is to be used in conjunction with the latest edition of EN 61347-1 and EN 61347-2-1. It was established on the basis of EN 61347-1:2008 and EN 61347-2-1:2001 + A1:2006. The following dates were fixed
15、: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2008-07-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2011-10-01 Annex ZA has been added by CENELEC. _ En
16、dorsement notice The text of the International Standard IEC 60927:2007 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following note has to be added for the standard indicated: IEC 60155 NOTE Harmonized as EN 60155:1996 (not mo
17、dified). _ 2 BS EN 60927:2007 Licensed Copy: London South Bank University, South Bank University, 31/01/2009 04:01, Uncontrolled Copy, (c) BSI 3 CONTENTS 1 Scope 5 2 Normative references .5 3 Definitions6 4 General requirements for tests7 4.1 Ambient conditions, test quantity and sequence of tests .
18、7 4.2 Supply voltage.7 4.3 Corresponding safety requirements7 4.4 Immunity .7 4.5 Relation to lamp standards 7 5 Marking7 6 Performance requirements for starters (other than glow starters) for fluorescent lamps.8 6.1 Starting test.8 6.1.1 Starting test quantity8 6.1.2 Conditions of acceptance .8 6.1
19、.3 Conditions of test.8 6.1.4 Starters having a mechanical switching element .9 6.1.5 Starters having an electronic switching element10 6.1.6 Non-reoperating level.11 6.1.7 Maximum pre-heat current (lamp fails to start) 12 6.1.8 Interruption of starter function 12 6.2 Endurance test 12 6.2.1 Test qu
20、antity12 6.2.2 Test conditions 12 6.2.3 Starters replaceable without tools.12 6.2.4 Starters not intended for replacement.12 6.2.5 Conditions of acceptance .12 6.3 Deactivated lamp test 13 6.3.1 Test quantity13 6.3.2 Test conditions 13 6.3.3 Starters with a mechanical switching element but without c
21、ut-out 13 6.3.4 Starters with an electronic switching element but without cut-out.13 6.3.5 Starters with a mechanical switching element and with thermal cut- out.13 6.3.6 Starters with an electronic switching element and electronic cut-out14 6.3.7 Condition of acceptance.14 7 Performance requirement
22、s for ignitors.14 7.1 Starting test.14 7.1.1 Test quantity14 7.1.2 Test conditions 14 7.1.3 Conditions of acceptance .14 7.1.4 Switching speed.15 7.1.5 Pulse voltage.15 7.1.6 Repetition rate, pulse position, width and height of starting pulse for triggered ignitors15 7.1.7 Ignition energy for non-tr
23、iggered ignitors 15 BS EN 60927:2007 Licensed Copy: London South Bank University, South Bank University, 31/01/2009 04:01, Uncontrolled Copy, (c) BSI 4 7.2 Non-reoperating level 15 7.3 Endurance test 16 7.3.1 Test quantity16 7.3.2 Test conditions 16 7.3.3 Ignitors without replaceable switching eleme
24、nts16 7.3.4 Ignitors with switching elements replaceable without tools 16 7.3.5 Ignitors with additional cut-outs 17 7.3.6 Conditions of compliance .17 Annex A (normative) Ballasts to be used for life testing 20 Annex B (informative) Explanation of starting conditions for electronic starters with an
25、 electronic switching element .21 Annex C (informative) A guide to quoting product life and failure rate29 Annex ZA (normative) Normative references to international publications with their corresponding European publications31 Bibliography .30 Figure 1 Pulse voltage measurement for starting devices
26、18 Figure 2 Ignition energy measurement for non-triggered starting devices 19 Figure B.1 Cathode heating current requirements for electronic starters with electronic switching element .25 Figure B.2 Interpretation of effective heating current.26 Figure B.3 Starters which remove pre-heating current w
27、hen open-circuit voltages are elevated .27 Figure B.4 Starters which have open-circuit voltage transition times higher than 100 ms .28 Table 1 Starting aid requirements.8 BS EN 60927:2007 Licensed Copy: London South Bank University, South Bank University, 31/01/2009 04:01, Uncontrolled Copy, (c) BSI
28、 5 _ AUXILIARIES FOR LAMPS STARTING DEVICES (OTHER THAN GLOW STARTERS) PERFORMANCE REQUIREMENTS 1 Scope This International Standard specifies performance requirements for starting devices (starters and ignitors) for tubular fluorescent and other discharge lamps for use on a.c. supplies up to 1 000 V
29、 at 50 Hz or 60 Hz, which produce starting pulses not greater than 5 kV. This standard is used in conjunction with IEC 61347-1 and IEC 61347-2-1. NOTE 1 All glow starters for fluorescent and other discharge lamps including thermal relay/cut-outs will be included in IEC 60155. NOTE 2 There are region
30、al standards regarding the regulation of EMC requirements for end-products like luminaires and independent control gear. In a luminaire, the control gear is dominant in this respect. Control gear, together with other components, should comply with these standards. 2 Normative references The followin
31、g referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60081, Double-capped fluorescent lamps Performance specif
32、ications IEC 60192, Low-pressure sodium vapour lamps Performance specifications IEC 60598-1:2003, Luminaires Part 1: General requirements and tests1) Amendment 1 (2006) IEC 60662, High-pressure sodium vapour lamps IEC 60901, Single-capped fluorescent lamps Performance specifications IEC 60921, Balla
33、sts for tubular fluorescent lamps Performance requirements IEC 60923, Auxiliaries for lamps Ballasts for discharge lamps (excluding tubular fluorescent lamps) Performance requirements IEC 61167, Metal halide lamps IEC 61347-1, Lamp controlgear - General and safety requirements IEC 61347-2-1, Lamp co
34、ntrolgear Particular requirements for starting devices (other than glow starters) 1) A consolidated edition 6.1 exists, including IEC 60598-1 (2003) and its Amendment 1 (2006). BS EN 60927:2007 Licensed Copy: London South Bank University, South Bank University, 31/01/2009 04:01, Uncontrolled Copy, (
35、c) BSI 6 IEC 61347-2-9, Lamp controlgear Particular requirements for ballasts for discharge lamps (excluding fluorescent lamps) IEC 61547, Equipment for general lighting purposes EMC immunity requirements 3 Terms and definitions For the purposes of this document, the terms and definitions of IEC 613
36、47-2-1 together with the following apply. 3.1 starter with mechanical switching element starter which provides cathode pre-heating current and lamp-starting pulse(s) by mechanical means (e.g. thermal or magnetic) 3.2 starter with electronic switching element starter which provides cathode pre-heatin
37、g current and lamp-starting voltage(s) or pulse(s) by electronic means and contains no moving parts 3.3 deactivated lamp lamp in which one or both cathodes are deprived of emitting material but neither of which is broken 3.4 non-re-operating level reduced level of voltage and/or current at which a s
38、tarting device must not re-operate after the completion of the starting cycle, and the lamp is operating normally 3.5 maximum abnormal current value of continuous r.m.s. current through the ballast which shall not be exceeded at the end of the starting cycle when the circuit is in an abnormal condit
39、ion (e.g. deactivated lamp, or lamp that has been removed) 3.6 starting aid means to facilitate the starting of a lamp, which can be either a conductive strip affixed to the outer surface of a lamp or a conductive plate which is placed within an appropriate distance from a lamp NOTE A starting aid c
40、an only be effective when it has an adequate potential difference from one end of the lamp. 3.7 maximum case temperature (tc + X) under abnormal conditions maximum allowable case temperature of the ignitor under abnormal conditions with metal halide lamps The value of (tc + X) is declared by the man
41、ufacturer BS EN 60927:2007 Licensed Copy: London South Bank University, South Bank University, 31/01/2009 04:01, Uncontrolled Copy, (c) BSI 7 4 General requirements for tests 4.1 Ambient conditions, test quantity and sequence of tests Only requirements for type tests are included. Unless otherwise s
42、pecified, the tests shall be made at an ambient temperature between 10 C and 30 C. The tests shall be carried out in the order of the clauses of this standard. The following numbers of samples shall be submitted: six samples of starters as defined in 3.1 and 3.2; four samples of ignitors (where appr
43、opriate, together with those circuit components which are necessary to carry out the tests). 4.2 Supply voltage The total harmonic content of the supply voltage shall not exceed 3 %, the harmonic content being defined as the root-mean-square (r.m.s.) summation of the individual harmonic components,
44、using the fundamental as 100 %. Care shall be taken that this applies under all conditions that occur during the measurement. NOTE This implies that the source of supply will have sufficient power and that the supply circuit has sufficiently low impedance at supply frequency and impulse frequency co
45、mpared with the ballast impedance. The correct impedance at impulse frequency can be obtained by connecting a 2 F (approximately) capacitor in parallel with the source. 4.3 Corresponding safety requirements All starting devices specified in this standard shall meet the requirements of IEC 61347-2-1.
46、 4.4 Immunity All starting devices specified in this standard shall meet the requirements of IEC 61547. NOTE The requirements for starting devices are under consideration in IEC 61547. 4.5 Relation to lamp standards Attention is drawn to lamp performance standards which contain “Information for igni
47、tor design”. This information should be followed for proper lamp operation. However, this standard does not require the testing of lamp performance as part of the type test approval for ignitors. 5 Marking The marking requirements of IEC 61347-2-1 shall apply, together with the following, to be eith
48、er clearly marked on the starting device or made available in the manufacturers catalogue, or the like. BS EN 60927:2007 Licensed Copy: London South Bank University, South Bank University, 31/01/2009 04:01, Uncontrolled Copy, (c) BSI 8 a) The manufacturer shall declare the type of switching element
49、as defined in 3.1 and 3.2. b) The manufacturer shall declare the maximum load capacitance for satisfactory operation of the ignitor. c) The manufacturer shall declare the allowable maximum case temperature under abnormal conditions (tc + X) of the ignitor. 6 Performance requirements for starters (other than glow starters) for fluorescent lamps This clause specifies perform