《BS-EN-61754-13-1999 IEC-61754-13-1999.pdf》由会员分享,可在线阅读,更多相关《BS-EN-61754-13-1999 IEC-61754-13-1999.pdf(18页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 61754-13:1999 IEC 61754-13: 1999 Fibre optic connector interfaces Part 13: Type FC-PC connector family The European Standard EN 61754-13:1999 has the status of a British Standard ICS 33.180.20 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 13 02:25:48 GMT+00:00 2006, Unco
2、ntrolled Copy, (c) BSI BS EN 61754-13:1999 This British Standard, having been prepared under the direction of the Electrotechnical Sector Committee, was published under the authority of the Standards Committee and comes into effect on 15 November 1999 BSI 03-2000 ISBN 0 580 35562 4 National foreword
3、 This British Standard is the English language version of EN 61754-13:1999. It is identical with IEC 61754-13:1999. The UK participation in its preparation was entrusted by Technical Committee GEL/86, Fibre optics to Subcommittee GEL/86/2, Interconnecting devices and passive components, which has th
4、e responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the
5、UK. A list of organizations represented on this subcommittee can be obtained on request to its secretary. From 1 January 1997, all IEC publications have the number 60000 added to the old number. For instance, IEC 27-1 has been renumbered as IEC 60027-1. For a period of time during the change over fr
6、om one numbering system to the other, publications may contain identifiers from both systems. Cross-references Attention is drawn to the fact that CEN and CENELEC Standards normally include an annex which lists normative references to international publications with their corresponding European publ
7、ications. The British Standards which implement these international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electr
8、onic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This doc
9、ument comprises a front cover, an inside front cover, pages i and ii, the EN title page, pages 2 to 13 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments i
10、ssued since publication Amd. No.DateComments Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 13 02:25:48 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 61754-13:1999 BSI 03-2000i Contents Page National forewordInside front cover Foreword2 Text of EN 61754-133 Licensed Copy: sheffieldun sheffie
11、ldun, na, Mon Nov 13 02:25:48 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ii blank Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 13 02:25:48 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 61754-13 August 1999 ICS 33.180.20Supersedes CECC 86115-80
12、2:1997 English version Fibre optic connector interfaces Part 13: Type FC-PC connector family (IEC 61754-13:1999) Interfaces de connecteurs pour fibres optiques Partie 13: Famille de connecteurs de type FC-PC (CEI 61754-13:1999) Steckgesichter von Lichtwellenleiter-Steckverbindern Teil 13: Bauart FC-
13、PC Steckverbinderfamilie (IEC 61754-13:1999) This European Standard was approved by CENELEC on 1999-08-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alte
14、ration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by t
15、ranslation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Gre
16、ece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat
17、: rue de Stassart 35, B-1050 Brussels 1999 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 61754-13:1999 E Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 13 02:25:48 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 61754-13:1999 B
18、SI 03-2000 2 Foreword The text of document 86B/1163/FDIS, future edition 1 of IEC 61754-13, prepared by SC 86B, Fibre optic interconnecting devices and passive components, of IEC TC 86, Fibre optics, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 61754-13 on 1999-08
19、-01. This European Standard supersedes CECC 86115-802:1997. The following dates were fixed: Endorsement notice The text of the International Standard IEC 61754-13:1999 was approved by CENELEC as a European Standard without any modification. Contents Page Foreword2 1Scope3 2Description3 3Interfaces3
20、Figure 1 Plug connector interface4 Figure 2 Plug connector interface Expanded view A5 Figure 3 Adaptor connector interface7 Figure 4 Adaptor connector interface Alignment sleeve8 Figure 5 Pin gauge for adaptor10 Figure 6 Active device receptacle interface11 Figure 7 Pin gauge for active device recep
21、tacle13 Table 1a Dimensions of the plug connector interface for Figure 1 and Figure 26 Table 1b Plug connector interface Ferrule grade6 Table 2a Dimensions of the adaptor connector interface for Figure 3 and Figure 49 Table 2b Adaptor connector interface Alignment sleeve grade (see Figure 3 and Figu
22、re 4)9 Table 3 Pin gauge grade10 Table 4a Dimensions of the active device receptacle interface for Figure 612 Table 4b Active device receptacle interface Alignment sleeve grade (see Figure 6)12 Table 5 Pin gauge grade13 latest date by which the EN has to be implemented at national level by publicati
23、on of an identical national standard or by endorsement(dop) 2000-05-01 latest date by which the national standards conflicting with the EN have to be withdrawn(dow) 2002-08-01 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 13 02:25:48 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 61754-13:1999
24、BSI 03-20003 1 Scope This part of IEC 61754 defines the standard interface dimensions for the type FC-PC family of connectors. 2 Description The parent connector for type FC connector family is a single position plug connector set of plug/adaptor configuration which is characterized by a 2,5 mm nomi
25、nal ferrule diameter. It includes a thread coupling mechanism, which is spring loaded relative to the ferrule in the direction of the optical axis. The plug has a single male key which may be used to orient and limit the relative position between the connector and the component to which it is mated.
26、 The optical alignment mechanism of the connectors is of a rigid bore sleeve or a resilient sleeve style. 3 Interfaces The subsequent pages define the standard interfaces for the type FC connector family. This standard contains the following standard interfaces: Interface 13-1: Plug connector interf
27、ace Interface 13-2: Adaptor connector interface Interface 13-3: Active device receptacle interface The plug of interface 13-1 has a ferrule with a spherically polished ferrule endface, and realizes physical contact (PC). The following connectors are intermateable Interface 13-1 mates with IEC interf
28、ace 13-2 and interface 13-3. Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 13 02:25:48 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 61754-13:1999 4 BSI 03-2000 Figure 1 Plug connector interface Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 13 02:25:48 GMT+00:00 2006, Uncontrolled Copy,
29、(c) BSI EN 61754-13:1999 BSI 03-20005 Figure 2 Plug connector interface Expanded view A Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 13 02:25:48 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 61754-13:1999 6 BSI 03-2000 Table 1a Dimensions of the plug connector interface for Figure 1 and Figur
30、e 2 Table 1b Plug connector interface Ferrule grade ReferenceDimensionsNotes MinimumBasicMaximum ADiameter, see ferrule grade table, 1 B4,4 mm4,6 mmDiameter C5,8 mm6,0 mmDiameter D2,92 mm E3,75 mm4,10 mm2 F1,77 mm2,77 mm GM8 0,75-6 H3 H1,1 mm4 I3,5 mm3 J3,95 mm K1,86 mm2,14 mm BF1025Radius, 5 BGDiam
31、eter, see ferrule grade table, 1 BI2535Degree, 1 NOTE 1The outside diameter of the ferrule may be less than 2,498 mm in the range of 1,2 mm from the tip rearwards. NOTE 2Dimension E is given for a plug endface when not mated. It is movable by a certain axial compression force, with direct contacting
32、 endfaces, and therefore dimension E is variable with a minimum length of 3,6 mm. Ferrule compression force shall be 7,8 N to 11,8 N when dimension E is from 3,6 mm to 3,7 mm. NOTE 3M8 0,75 indicates a metric screw thread with a nominal diameter of 8 mm and a pitch of 0,75 mm. 6H represents the clas
33、s of fit. It requires a way of escape from the thread rearwards. NOTE 4The coupling sleeve shall be movable towards right and left directions. This dimension is given when the coupling sleeve is moved furthermost to the right. NOTE 5Dome eccentricity of the spherically polished endface shall be less
34、 than 0,05 mm. Grade A mm BG mm Notes MinimumMaximumMinimumMaximum 12,49852,49951,702,26 22,49802,49951,702,26 32,49852,49951,902,20 42,49802,49951,902,20 52,49702,49951,802,20 62,49402,49951,802,20 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 13 02:25:48 GMT+00:00 2006, Uncontrolled Copy, (c
35、) BSI EN 61754-13:1999 BSI 03-20007 Figure 3 Adaptor connector interface Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 13 02:25:48 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 61754-13:1999 8 BSI 03-2000 Figure 4 Adaptor connector interface Alignment sleeve Licensed Copy: sheffieldun sheffiel
36、dun, na, Mon Nov 13 02:25:48 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 61754-13:1999 BSI 03-20009 Table 2a Dimensions of the adaptor connector interface for Figure 3 and Figure 4 Table 2b Adaptor connector interface Alignment sleeve grade (see Figure 3 and Figure 4) Notes to Table 2a and Table 2
37、b NOTE 1The connector alignment feature is a resilient alignment sleeve or a rigid bore sleeve. Dimension A defines the inner diameter of the alignment feature. NOTE 2M8 0,75 indicates a metric screw thread with a nominal diameter of 8 mm and pitch of 0,75 mm. 6g represents the class of fit. It requ
38、ires a way of escape from the thread rearwards. NOTE 3The minimum rectangular envelope for the keyway is defined by dimensions K and F. NOTE 4This dimension shall be applied to an adaptor having a resilient alignment sleeve. NOTE 5The connector alignment feature is an alignment sleeve. The feature s
39、hall accept a pin gauge to the centre of the adaptor with a force of 2 N to 5,9 N with another pin gauge inserted into the feature from the other side until both pin gauges butt each other. The pin gauge shall be No. 2,499 in the pin gauge grade table. The centre of the adaptor is defined by the rig
40、ht side position of the dimension E. NOTE 6Add grade number to the interface reference number. NOTE 7The connector alignment feature is a rigid bore sleeve. The dimension A shall be tested using two pin gauges. One pin gauge has the pin gauge grade number 1 4m larger than the maximum value of the di
41、mension A, the other pin gauge has the pin gauge grade number 1 4m smaller than the minimum value of the dimension A. The appropriate pin gauges shall be selected from the pin gauge grade table. Reference Dimensions mm Notes MinimumMaximum ADiameter, see grade table, 1 B3,994,38Diameter C6,016,20Dia
42、meter D2,152,9 E3,63,7 F0,751,743 GM8 0,75-6g2 H0,4 I2,82 J3,653,9 K2,152,63 N2,552,704 Grade A mm Notes MinimumMaximum 1Resilient sleeve, 5, 6 22,5002,502Rigid bore sleeve, 6, 7 32,5012,504 42,5012,506 52,5012,525 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 13 02:25:48 GMT+00:00 2006, Uncon
43、trolled Copy, (c) BSI EN 61754-13:1999 10 BSI 03-2000 Table 3 Pin gauge grade Figure 5 Pin gauge for adaptor Pin gauge grade CK mm CL mm CN mm Notes MinimumMaximumMinimumMaximumMinimumMaximum 2,4992,49852,49952,84,8715Resilient sleeve and rigid bore sleeve, 1 2,5002,49952,5005 Rigid bore sleeve, 1 2
44、,5032,50252,5035 2,5052,50452,5055 2,5072,50652,5075 2,5262,52552,5265 NOTESurface roughness should be grade N4 (0,2 4m Ra) and cylindricity is less than 0,5 4m. Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 13 02:25:48 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 61754-13:1999 BSI 03-200011
45、Figure 6 Active device receptacle interface Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 13 02:25:48 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 61754-13:1999 12 BSI 03-2000 Table 4a Dimensions of the active device receptacle interface for Figure 6 Table 4b Active device receptacle interfac
46、e Alignment sleeve grade (see Figure 6) Notes to Table 4a and Table 4b NOTE 1The connector alignment feature is a rigid bore sleeve or a resilient alignment sleeve. Dimension A defines the inner diameter of the alignment feature. NOTE 2M8 0,75 indicates a metric screw thread with a nominal diameter
47、of 8 mm and pitch of 0,75 mm. 6g represents the class of fit. It requires a way of escape from the thread rearwards. NOTE 3The minimum rectangular envelope for the keyway is defined by dimensions K and F. NOTE 4The connector alignment feature is a rigid bore sleeve. The dimension A shall be tested u
48、sing two pin gauges. One pin gauge has the pin gauge grade number 1 4m larger than maximum value of the dimension A, the other pin gauge has the pin gauge grade number 1 4m smaller than the minimum value of the dimension A. The appropriate pin gauge shall be selected from the pin gauge grade table.
49、NOTE 5The connector alignment feature is an alignment sleeve. The feature shall accept a pin gauge to the centre of the adaptor with a force of 2 N to 5,9 N with another pin gauge inserted into the feature from the other side until both pin gauges butt each other. The pin gauge shall be No. 2,499 in the pin gauge grade table. NOTE 6Add grade number to the interface reference number. Reference Dimensions mm Notes MinimumMaximum ADiameter, see grade ta