《BS-EN-ISO-10087-1996.pdf》由会员分享，可在线阅读，更多相关《BS-EN-ISO-10087-1996.pdf（10页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS EN ISO 10087:1996 Incorporating Amendment No. 1 Small craft Hull identification Coding system The European Standard EN ISO 10087:1996, with the incorporation of amendment A1:2000, has the status of a British Standard ICS 47.080 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTE
2、D BY COPYRIGHT LAW Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 19 13:03:25 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN ISO 10087:1996 This British Standard, having been prepared under the direction of the Engineering Sector Board, was published under the authority of the Standards Board
3、 and comes into effect on 15 May 1996 BSI 05-2001 The following BSI references relate to the work on this standard: Committee reference GME/33 Draft for comment 94/703839 DC ISBN 0 580 25638 3 Committees responsible for this British Standard The preparation of this British Standard was entrusted to
4、Technical Committee GME/33, Small craft, upon which the following bodies were represented: British Canoe Manufacturers Association British Marine Industries Federation British Nautical Instrument Trade Association British Waterways Board Consumer Policy Committee of BSI Department of Trade and Indus
5、try Department of Trade and Industry (Standards Policy Unit) Federation of Wire Rope Manufacturers of Great Britain Fire Extinguishing Trades Association Home Office Lloyds Register of Shipping National Rivers Authority Personal Watercraft Association Royal Ocean Racing Club Royal Society for the Pr
6、evention of Accidents Royal Yachting Association Co-opted members Amendments issued since publication Amd. No.DateComments 12075May 2001Addition of Annex ZB Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 19 13:03:25 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN ISO 10087:1996 BSI 05-2001 i C
7、ontents Page Committees responsibleInside front cover National forewordii Foreword2 1Scope3 2Normative reference3 3Definition3 4Composition of Hull Identification Number (HIN)3 5Requirements4 6Additional information4 Annex ZA (normative) Normative references to international publications with their
8、relevant European publications5 Annex ZB (informative) Clauses of the European Standard addressing essential requirements or other provision of EU Directives5 Table 13 Table ZB.1 Correspondence between this European Standard and EU Directives5 Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 19 1
9、3:03:25 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN ISO 10087:1996 ii BSI 05-2001 National foreword This British Standard has been prepared by Technical Committee GME/33 and is the English language version of EN ISO 10087:1996, Small craft Hull identification Coding system, including amendment
10、A1:2000, published by the European Committee for Standardization (CEN). It is identical with ISO 10087:1995 published by the International Organization for Standardization (ISO). It supersedes BS 7490:1991 which is withdrawn. Cross-reference The British Standard which implement international or Euro
11、pean publications referred to in this document may be found in the BSI Standard catalogue under the section entitled “International Standards Correspondence Index” or by using the “Find” facility of the BSI Standard Electronic Catalogue. A British Standard does not purport to include all the necessa
12、ry provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, the EN t
13、itle page, pages 2 to 5 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 19 13:03:25 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN I
14、SO 10087 January 1996 + A1 September 2000 ICS 47.080 Descriptors: Shipbuilding, pleasure boats, ship hulls, identification methods, international identification number, coded representation English version Small craft Hull identification Coding system (includes amendment A1:2000) (ISO 10087:1995) Na
15、vires de plaisance Identification des coques Systme de codage (inclut lamendment A1:2000) (ISO 10087:1995) Kleine Wasserfahrzeuge Schiffskrper-Kennzeichnung Codierungssystem (enthlt nderung A1:2000) (ISO 10087:1995) This European Standard was approved by CEN on 1995-12-06. Amendment A1:2000 was appr
16、oved by CEN on 2000-09-01. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national sta
17、ndards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified t
18、o the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Czech Republic, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and Uni
19、ted Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1996 Copyright reserved to CEN members Ref. No. EN ISO 10087:1996 + A1:2000E Licensed Copy: sheffieldun sheffieldun, na, Sun
20、Nov 19 13:03:25 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN ISO 10087:1996 BSI 05-2001 2 Foreword The text of the International Standard from ISO/TC 188, Small craft, of the International Organization for Standardization (ISO) has been taken over as a European Standard by the CEN Technical Board.
21、This European Standard has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EC Directive(s). This European Standard shall be given the status of a national standard, either by publication of an ident
22、ical text or by endorsement, at the latest by July 1996, and conflicting national standards shall be withdrawn at the latest by July 1996. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard:
23、 Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. NOTENormative references to international publications are listed in Annex ZA (normative). Foreword to amendment A1 The
24、 text of this amendment EN ISO 10087:1996/ A1:2000 to the EN ISO 10087:1996 from Technical Committee ISO/TC 188, Small craft, of the International Organization for Standardization (ISO) has been taken over as an amendment to the European Standard by CEN/CMC. This amendment to the European Standard E
25、N ISO 10087:1996 shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March 2001, and conflicting national standards shall be withdrawn at the latest by March 2001. This amendment to the European Standard EN ISO 10087:1996 h
26、as been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZB, which is an integral part of this standard. According to the CEN/
27、CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden,
28、 Switzerland and United Kingdom. Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 19 13:03:25 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN ISO 10087:1996 BSI 05-2001 3 1 Scope This International Standard establishes a coding system to achieve identification of any small craft hull, concerning id
29、entification code of the country; identification code of the manufacturer; serial number; month and year of production; model year. It applies to small craft of all types and materials, of length of hull of up to 24 m. It does not apply to beach or bathing toys. 2 Normative reference The following s
30、tandard contains provisions which, through reference in this text, constitute provisions of this International Standard. At the time of publication, the edition indicated was valid. All standards are subject to revision, and parties to agreements based on this International Standard are encouraged t
31、o investigate the possibility of applying the most recent edition of the standard indicated below. Members of IEC and ISO maintain registers of currently valid International Standards. ISO 3166:1993, Codes for the representation of names of countries. 3 Definition For the purposes of this Internatio
32、nal Standard, the following definition applies. 3.1 hull identification number (HIN) unique series of numerals, letters and hyphen, permanently affixed to a craft hull 4 Composition of hull identification number (HIN) A HIN shall consist of 14 consecutive characters plus a hyphen as given in 4.1, 4.
33、2, 4.3 and 4.4 without intervening spaces, solidi (slashes) or dashes. 4.1 The first two characters, followed by a hyphen, designate the code of the country in which the craft was manufactured, as specified in the ISO alpha-2 code in ISO 3166. The manufacturer may be any company involved in the prod
34、uction of the small craft. Where more than one company is involved, the “manufacturer” is the company that registers the manufacturers identifying code. 4.2 The next three characters are the unique identification code of the manufacturer, assigned by a national authority or recognized organization.
35、These characters shall be letters. 4.3 The following five characters indicate the serial number of the craft as assigned by the manufacturer. The serial number may consist of numerals and/or letters, except for letters I, O and Q. 4.4 The last four characters designate the month and year of producti
36、on, and the model year. The month of production shall be coded according to Table 1. Table 1 The year of manufacture shall be identified by the last numeral of the production year. The model year shall be identified by the last two numerals of the year in question. NOTE 1The model year is a twelve-m
37、onth period, during which the particular craft model is intended to be sold. Craft designated for a model year may be built during a preceding calendar year. MonthCodeMonthCode JanuaryAJulyG FebruaryBAugustH MarchCSeptemberI AprilDOctoberJ MayENovemberK JuneFDecemberL Licensed Copy: sheffieldun shef
38、fieldun, na, Sun Nov 19 13:03:25 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN ISO 10087:1996 4 BSI 05-2001 4.5 HIN Example: NL-HXAB7A33G293 where 5 Requirements 5.1 Size The size of the characters shall be at least 6 mm high. 5.2 Permanency of marking Each HIN shall be carved, burned, stamped, embo
39、ssed, moulded or otherwise permanently affixed so that alteration, removal or replacement will be obvious. If on a plate, the plate shall be fastened so that its removal will cause scarring to the surrounding area. 5.3 Location The HIN shall be visible on the starboard outboard side of the transom,
40、or near the stern within 50 mm of the transom top, gunwale, hull/deck joint or its capping, whichever is lowest. 5.3.1 On craft with a transom, the HIN shall be located on the starboard side of the transom. 5.3.2 On craft without a transom or with a transom on which it is impractical to locate the H
41、IN, the HIN shall be affixed within 300 mm of the stern. 5.3.3 On catamarans the HIN shall be located as follows: hulls structurally permanently connected: on the starboard hull; hulls detachable but regarded as the primary structure: on both hulls; hulls readily removable and/or replaceable: on the
42、 aft cross-beam within 300 mm of the starboard hull; this also applies to catamaran-type pontoon boats. 5.3.4 On trimarans the HIN shall be located on the centre hull in accordance with 5.3.1 or 5.3.2. 5.3.5 On inflatable boats the HIN shall be affixed on the rigid aft cross-beam or motor bracket wi
43、thin 300 mm of the starboard hull attachment. If the HIN is not readily visible due to the construction of the boat, the hull identification number may be applied additionally to some other suitable structure of the boat, such as the console assembly. 5.3.6 Rails, fittings or other accessories shall
44、 not obscure the HIN located as specified above. If the design of the small craft would result in this, the HIN shall be located as near as possible to the required location to be visible. 5.4 Duplicate HIN A duplicate HIN shall be affixed to a non-removable part of the craft in a hidden location in
45、 the interior or beneath a fitting or item of hardware. Catamarans shall have this hidden HIN in or on both hulls. 5.5 Time of HIN marking The HIN shall be affixed to the craft during the construction of the hull. In no case shall the craft be put on the market without the HIN being affixed. 5.6 Dis
46、play format The HIN shall be displayed in alphanumerical characters (arabic numerals and upper case letters) and shall read from left to right. 6 Additional information If additional information is displayed on the craft within 50 mm of the HIN, it shall be separated from the HIN by means of borders
47、 or it shall be on a separate label so that it will not be interpreted as part of the HIN. Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 19 13:03:25 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN ISO 10087:1996 BSI 05-2001 5 Annex ZA (normative) Normative references to international publication
48、s with their relevant European publications This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent am
49、endments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. Annex ZB (informative) Clauses of this European Standard addressing essential requirements or other provisions of EU Directives This European Standard has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association and supports essential requirements of EU