《BS-EN-60384-6-2005.pdf》由会员分享,可在线阅读,更多相关《BS-EN-60384-6-2005.pdf(30页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 60384-6:2005 Fixed capacitors for use in electronic equipment Part 6: Sectional specification Fixed metallized polycarbonate film dielectric d.c. capacitors The European Standard EN 60384-6:2005 has the status of a British Standard ICS 31.060.30 ? Licensed Copy: sheffieldun sh
2、effieldun, na, Sat Nov 11 02:13:29 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 60384-6:2005 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 June 2006 BSI 2006 ISBN 0 580 48812 8 National foreword This British Standard is the official
3、English language version of EN 60384-6:2005. It is identical with IEC 60384-6:2005. It supersedes BS EN 130500:1998 which will be withdrawn on 1 October 2008. The UK participation in its preparation was entrusted to Technical Committee EPL/40X, Capacitors and resistors for electronic equipment, whic
4、h has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the secti
5、on entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Co
6、mpliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep UK interests informed; monitor related
7、international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 26, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the docume
8、nt was last issued. Amendments issued since publication Amd. No. DateComments Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 02:13:29 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD EN 60384-6 NORME EUROPENNE EUROPISCHE NORM October 2005 CENELEC European Committee for Electrotec
9、hnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2005 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. E
10、N 60384-6:2005 E ICS 31.060.30 Supersedes EN 130500:1998 English version Fixed capacitors for use in electronic equipment Part 6: Sectional specification Fixed metallized polycarbonate film dielectric d.c. capacitors (IEC 60384-6:2005) Condensateurs fixes utiliss dans les quipements lectroniques Par
11、tie 6: Spcification intermdiaire Condensateurs fixes pour courant continu dilectrique en film de polycarbonate mtallis (CEI 60384-6:2005) Festkondensatoren zur Verwendung in Gerten der Elektronik Teil 6: Rahmenspezifikation Festkondensatoren fr Gleichspannung mit metallisierten Kunststofffolien aus
12、Polykarbonat als Dielektrikum (IEC 60384-6:2005) This European Standard was approved by CENELEC on 2005-10-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any
13、alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made
14、by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland,
15、 France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 02:13:29 GMT+00:00 2006, Uncontrolled Cop
16、y, (c) BSI Foreword The text of document 40/1588/FDIS, future edition 3 of IEC 60384-6, prepared by IEC TC 40, Capacitors and resistors for electronic equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60384-6 on 2005-10-01. This European Standard supersedes
17、EN 130500:1998. The following dates were fixed: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2006-07-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2008-
18、10-01 Annex ZA has been added by CENELEC. _ Endorsement notice The text of the International Standard IEC 60384-6:2005 was approved by CENELEC as a European Standard without any modification. _ EN 60384-6:2005 2 Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 02:13:29 GMT+00:00 2006, Uncontro
19、lled Copy, (c) BSI 3 EN 60384-6:2005 CONTENTS 1 General4 1.1 Scope4 1.2 Normative references 4 1.3 Information to be given in a detail specification 5 1.4 Terms and definitions 6 1.5 Marking.6 2 Preferred ratings and characteristics.7 2.1 Preferred characteristics7 2.2 Preferred values of ratings.7
20、3 Quality assessment procedures 8 3.1 Primary stage of manufacture 8 3.2 Structurally similar components .8 3.3 Certified records of released lots8 3.4 Qualification approval 8 3.5 Quality conformance inspection .15 4 Test and measurement procedures .16 4.1 Visual examination and check of dimensions
21、16 4.2 Electrical tests.16 4.3 Robustness of terminations20 4.4 Resistance to soldering heat20 4.5 Solderability 20 4.6 Rapid change of temperature.21 4.7 Vibration21 4.8 Bump 21 4.9 Shock22 4.10 Climatic sequence .22 4.11 Damp heat, steady state 23 4.12 Endurance.23 4.13 Charge and discharge24 4.14
22、 Component solvent resistance .25 4.15 Solvent resistance of the marking 25 Annex ZA (normative) Normative references to international publications with their corresponding European publications.26 Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 02:13:29 GMT+00:00 2006, Uncontrolled Copy, (c)
23、 BSI EN 60384-6:2005 4 FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT Part 6: Sectional specification Fixed metallized polycarbonate film dielectric d.c. capacitors 1 General 1.1 Scope This part of IEC 60384 applies to fixed capacitors for direct current with metallized electrodes and polycarbonat
24、e dielectric for use in electronic equipment. These capacitors may have “self-healing properties“ depending on conditions of use. They are primarily intended for applications where the a.c. component is small with respect to the rated voltage. Two performance grades of capacitors are covered, Grade
25、1 for long-life application and Grade 2 for general application. Capacitors for electromagnetic interference and connection to the supply mains are not included but are covered by IEC 60384-14. 1.2 Normative references The following referenced documents are indispensable for the application of this
26、document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60063:1963, Preferred number series for resistors and capacitors Amendment 1 (1967) Amendment 2 (1977) IEC 60068-1: Environmen
27、tal testing Part 1: General and guidance IEC 60384-1:1999, Fixed capacitors for use in electronic equipment Part 1: Generic specification IEC 60384-6-1, Fixed capacitors for use in electronic equipment Part 6-1: Blank detail specification Fixed metallized polycarbonate film dielectric d.c. capacitor
28、s - Assessment level E IEC 60384-14: Fixed capacitors for use in electronic equipment Part 14: Sectional specification: Fixed capacitors for electromagnetic interference suppression and connection to the supply mains IEC QC 001005: Register of Firms, Products and Services approved under the IECQ sys
29、tem, including ISO 9000 ISO 3:1973, Preferred numbers Series of preferred numbers Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 02:13:29 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 5 EN 60384-6:2005 1.3 Information to be given in a detail specification Detail specifications shall be derived
30、from the relevant blank detail specification. Detail specifications shall not specify requirements inferior to those of the generic, sectional or blank detail specification. When more severe requirements are included, they shall be listed in 1.9 of the detail specification and indicated in the test
31、schedules, for example, by an asterisk. NOTE The information given in 1.3.1 may, for convenience, be presented in tabular form. The following information shall be given in each detail specification and the values quoted shall preferably be selected from those given in the appropriate clause of this
32、sectional specification. 1.3.1 Outline drawing and dimensions There shall be an illustration of the capacitor as an aid to easy recognition and for comparison of the capacitor with others. Dimensions and their associated tolerances, which affect interchangeability and mounting, shall be given in the
33、 detail specification. All dimensions shall be stated in millimetres. Normally, the numerical values shall be given for the length of the body, the width and height of the body and the wire spacing, or, for cylindrical types, the body diameter and the length and diameter of the terminations. When ne
34、cessary, for example, when a number of items (capacitance values/voltage ranges) are covered by a detail specification, the dimensions and their associated tolerances shall be placed in a table below the drawing. When the configuration is other than described above, the detail specification shall st
35、ate such dimensional information as will adequately describe the capacitor. When the capacitor is not designed for use on printed boards, this shall be clearly stated in the detail specification. 1.3.1.1 Mounting The detail specification shall specify the method of mounting to be applied for normal
36、use and for the application of the vibration and the bump or shock tests. The capacitors shall be mounted by their normal means. The design of the capacitor may be such that special mounting fixtures are required in its use. In this case, the detail specification shall describe the mounting fixtures
37、 and they shall be used in the application of the vibration and bump or shock tests. 1.3.2 Ratings and characteristics The ratings and characteristics shall be in accordance with the relevant clauses of this specification, together with the following. 1.3.2.1 Rated capacitance range See 2.2.1. NOTE
38、When products approved to the detail specification have different ranges, the following statement should be added: “The range of capacitance values available in each voltage range is given in IEC QC 001005.”. 1.3.2.2 Particular characteristics Additional characteristics may be listed, when they are
39、considered necessary, to specify adequately the component for design and application purposes. Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 02:13:29 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 60384-6:2005 6 1.3.2.3 Soldering The detail specification shall prescribe the test methods, sev
40、erities and requirements applicable for the solderability and the resistance to soldering heat test. 1.3.3 Marking The detail specification shall specify the content of the marking on the capacitor and on the package. Deviations from 1.5 of this specification shall be specifically stated. 1.4 Terms
41、and definitions For the purposes of this document, the terms and definitions of IEC 60384-1, as well as the following, apply. 1.4.1 performance grade 1 capacitors (long-life) capacitors for long-life applications with stringent requirements for the electrical parameters 1.4.2 performance grade 2 cap
42、acitors (general purpose) capacitors for general application where the stringent requirements for Grade 1 capacitors are not necessary 1.4.3 rated voltage maximum d.c. voltage which may be applied continuously to a capacitor at the rated temperature NOTE The sum of the d.c. voltage and the peak a.c.
43、 voltage applied to the capacitor should not exceed the rated voltage. The value of the peak a.c. voltage should not exceed the following percentages of the rated voltage at the frequencies stated and should not be greater than 280 V: 50 Hz : 20 % 100 Hz : 15 % 1 000 Hz : 3 % 10 000 Hz : 1 % unless
44、otherwise specified in the detail specification. 1.5 Marking See 2.4 of IEC 60384-1 with the following details. 1.5.1 The information given in the marking is normally selected from the following list; the relative importance of each item is indicated by its position in the list: a) rated capacitance
45、; b) rated voltage (d.c. voltage may be indicated by the symbol or ); c) tolerance on rated capacitance; d) category voltage; e) year and month (or week) of manufacture; f) manufacturers name or trade mark; g) climatic category; h) manufacturers type designation; i) reference to the detail specifica
46、tion. Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 02:13:29 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 7 EN 60384-6:2005 1.5.2 The capacitor shall be clearly marked with a), b) and c) above and with as many as possible of the remaining items as is considered necessary. Any duplication of i
47、nformation in the marking on the capacitor should be avoided. 1.5.3 The package containing the capacitor(s) shall be clearly marked with all the information listed in 1.5.1. 1.5.4 Any additional marking shall be applied so that no confusion can arise. 2 Preferred ratings and characteristics 2.1 Pref
48、erred characteristics The values given in detail specifications shall preferably be selected from the following. 2.1.1 Preferred climatic categories The capacitors covered by this specification are classified into climatic categories according to the general rules given in IEC 60068-1. The lower and
49、 upper category temperatures and the duration of the damp-heat steady-state test shall be chosen from the following: lower category temperature: -55 C; 40 C; and 25 C; upper category temperature: +85 C, +100 C and +125 C duration of the damp-heat, steady-state test: 4, 10, 21 and 56 days. NOTE With continuous operation at 125 C in excess of the endurance test time, accelerated ageing should be con