《BS-ISO-IEC-7816-6-2004.pdf》由会员分享，可在线阅读，更多相关《BS-ISO-IEC-7816-6-2004.pdf（28页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS ISO/IEC 7816-6:2004 Identification cards Integrated circuit cards Part 6: Interindustry data elements for interchange ICS 35.240.15 ? Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 0
2、8/14/2008 22:43:24 MDTNo reproduction or networking permitted without license from IHS -,-,- BS ISO/IEC 7816-6:2004 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 March 2008 BSI 2008 ISBN 978 0 580 62216 8 National foreword This British S
3、tandard is the UK implementation of ISO/IEC 7816-6:2004. The UK participation in its preparation was entrusted to Technical Committee IST/17, Cards and personal identification. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does no
4、t purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. Amendments/corrigenda issued since publication DateComments Copyright British Standards Institution Pr
5、ovided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 22:43:24 MDTNo reproduction or networking permitted without license from IHS -,-,- Reference number ISO/IEC 7816-6:2004(E) INTERNATIONAL STANDARD ISO/IEC 7816-6 Second edition 2004-05-15
6、 Identification cards Integrated circuit cards Part 6: Interindustry data elements for interchange Cartes didentification Cartes circuit intgr Partie 6: lments de donnes intersectoriels pour les changes BS ISO/IEC 7816-6:2004 Copyright British Standards Institution Provided by IHS under license with
7、 BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 22:43:24 MDTNo reproduction or networking permitted without license from IHS -,-,- ii Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not
8、 for Resale, 08/14/2008 22:43:24 MDTNo reproduction or networking permitted without license from IHS -,-,- iii Contents Page Forewordiv Introduction .vi 1 Scope1 2 Normative references .1 3 Terms and definitions.1 4 Abbreviations and notation2 5 Maintenance of interindustry data objects.2 6 Specific
9、 interindustry data elements 2 7 Identification of integrated circuit manufacturers.5 8 Interchange profile6 9 Interindustry data elements in alphabetic order7 10 Interindustry tags in numeric order 12 11 Interindustry templates 15 Annex A (normative) Application for integrated circuit manufacturers
10、 number.18 Bibliography .19 BS ISO/IEC 7816-6:2004 Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 22:43:24 MDTNo reproduction or networking permitted without license from IHS -,-,- iv Forewor
11、d ISO (the International Organization for Standardization) and IEC (the International Electrotechnical Commission) form the specialized system for worldwide standardization. National bodies that are members of ISO or IEC participate in the development of International Standards through technical com
12、mittees established by the respective organization to deal with particular fields of technical activity. ISO and IEC technical committees collaborate in fields of mutual interest. Other international organizations, governmental and non-governmental, in liaison with ISO and IEC, also take part in the
13、 work. In the field of information technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of the joint technical committee is to prepare International
14、 Standards. Draft International Standards adopted by the joint technical committee are circulated to national bodies for voting. Publication as an International Standard requires approval by at least 75 % of the national bodies casting a vote. Attention is drawn to the possibility that some of the e
15、lements of this document may be the subject of patent rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights. ISO/IEC 7816-6 was prepared by Joint Technical Committee ISO/IEC JTC 1, Identification cards, Subcommittee SC 17, Cards and personal identification.
16、This second edition, together with the second editions of parts 4, 5, 8 and 9, after an in-depth reorganization of these five parts, cancels and replaces: ISO/IEC 7816-4:1995, Information technology Identification cards Integrated circuit(s) cards with contacts Part 4: Interindustry commands for int
17、erchange ISO/IEC 7816-4:1995/Amd.1:1997, Information technology Identification cards Integrated circuit(s) cards with contacts Part 4: Interindustry commands for interchange Amendment 1: Impact of secure messaging on the structure of APDU messages ISO/IEC 7816-5:1994, Identification cards Integrated
18、 circuit(s) cards with contacts Part 5: Numbering system and registration procedure for application identifiers ISO/IEC 7816-5:1994/Amd.1:1996, Identification cards Integrated circuit(s) cards with contacts Part 5: Numbering system and registration procedure for application identifiers Amendment 1 I
19、SO/IEC 7816-6:1996, Identification cards Integrated circuit(s) cards with contacts Part 6: Interindustry data elements ISO/IEC 7816-6:1996/Cor.1:1998, Identification cards Integrated circuit(s) cards with contacts Part 6: Interindustry data elements Technical corrigendum 1 ISO/IEC 7816-6:1996/Amd.1:
20、2000, Identification cards Integrated circuit(s) cards with contacts Part 6: Interindustry data elements Amendment 1: IC manufacturer registration ISO/IEC 7816-8:1999, Identification cards Integrated circuit(s) cards with contacts Part 8: Security- related interindustry commands ISO/IEC 7816-9:2000,
21、 Identification cards Integrated circuit(s) cards with contacts Part 9: Additional interindustry commands and security attributes BS ISO/IEC 7816-6:2004 Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08
22、/14/2008 22:43:24 MDTNo reproduction or networking permitted without license from IHS -,-,- v ISO/IEC 7816 consists of the following parts, under the general title Identification cards Integrated circuit cards: Part 1: Cards with contacts Physical characteristics Part 2: Cards with contacts Dimensio
23、ns and location of the contacts Part 3: Cards with contacts Electrical interface and transmission protocols Part 4: Organization, security and commands for interchange Part 5: Registration of application providers Part 6: Interindustry data elements for interchange Part 7: Interindustry Commands for
24、 Structured Card Query Language (SCQL) Part 8: Commands for security operations Part 9: Commands for card management Part 10: Cards with contacts Electrical interface for synchronous cards Part 11: Personal verification through biometric methods Part 15: Cryptographic information application BS ISO/
25、IEC 7816-6:2004 Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 22:43:24 MDTNo reproduction or networking permitted without license from IHS -,-,- vi Introduction ISO/IEC 7816 is a series of s
26、tandards specifying integrated circuit cards and the use of such cards for interchange. These cards are identification cards intended for information exchange negotiated between the outside world and the integrated circuit in the card. As a result of an information exchange, the card delivers inform
27、ation (computation result, stored data), and / or modifies its content (data storage, event memorization). Five parts are specific to cards with galvanic contacts and three of them specify electrical interfaces. ISO/IEC 7816-1 specifies physical characteristics for cards with contacts. ISO/IEC 7816-
28、2 specifies dimensions and location of the contacts. o ISO/IEC 7816-3 specifies electrical interface and transmission protocols for asynchronous cards. o ISO/IEC 7816-10 specifies electrical interface and answer to reset for synchronous cards. o ISO/IEC 7816-12 specifies electrical interface and ope
29、rating procedures for USB cards. All the other parts are independent from the physical interface technology. They apply to cards accessed by contacts and / or by radio frequency. ISO/IEC 7816-4 specifies organization, security and commands for interchange. ISO/IEC 7816-5 specifies registration of ap
30、plication providers. ISO/IEC 7816-6 specifies interindustry data elements for interchange. ISO/IEC 7816-7 specifies commands for structured card query language. ISO/IEC 7816-8 specifies commands for security operations. ISO/IEC 7816-9 specifies commands for card management. ISO/IEC 7816-11 specifies
31、 personal verification through biometric methods. ISO/IEC 7816-15 specifies cryptographic information application. ISO/IEC 1053614 specifies access by close coupling. ISO/IEC 1444317 and ISO/IEC 1569318 specify access by radio frequency. Such cards are also known as contactless cards. BS ISO/IEC 781
32、6-6:2004 Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 22:43:24 MDTNo reproduction or networking permitted without license from IHS -,-,- 1 Identification cards Integrated circuit cards Part
33、 6: Interindustry data elements for interchange 1 Scope This document specifies, directly or by reference, data elements, including composite data elements, that may be used in interindustry interchange. It identifies the following characteristics of each data element: identifier; name; description
34、and reference; format and coding (if not available in other ISO International Standards or parts of ISO/IEC 7816). The layout of each data element is described as seen at the interface between the interface device and the card. This document provides the definition of data elements without considera
35、tion of any restrictions on the usage of the data elements. It does not cover the internal implementation within the card and/or the outside world. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition
36、 cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO/IEC 7816 (all parts), Identification cards Integrated circuit cards 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1
37、data element item of information seen at the interface for which are defined a name, a description of logical content, a format and a coding ISO/IEC 7816-4 3.2 data object information seen at the interface consisting of the concatenation of a mandatory tag field, a mandatory length field and a condi
38、tional value field ISO/IEC 7816-4 When an application uses an interindustry template, it is allowed to nest within this template tags of context specific class (see ISO/IEC 7816-4) unless previously marked as Reserved for Future Use by ISO/IEC JTC1/SC17. BS ISO/IEC 7816-6:2004 Copyright British Stan
39、dards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 22:43:24 MDTNo reproduction or networking permitted without license from IHS -,-,- 2 3.3 template set of BER-TLV data objects forming the value field of a constructed
40、 BER-TLV data object ISO/IEC 7816-4 4 Abbreviations and notation For the purposes of this document, the following notation applies. numeric (binary-coded decimal format) ans alphanumeric and special characters . denotes a range of values between two numbers Any number following the notation denotes
41、the number of digits or characters. For example, a3 means three alphabetic characters; n2.4 means two, three or four binary-coded decimal digits. If the number of bits representing a data element is not a multiple of eight, then the mapping into a byte string should be defined in the context of the
42、respective data element. If not specified otherwise, the appropriate number of bits shall be set to one in the last byte starting from bit 1. 5 Maintenance of interindustry data objects It is the intention that every interindustry data object, specified at the time of publication, should be listed i
43、n this document. To allow the introduction, deletion or amendment of any data object, the following procedures shall be adopted: Interindustry data objects from ISO/IEC 7816 if any part of ISO/IEC 7816 introduces new data objects, then the normal ballot process shall approve them. Following publicat
44、ion of that part of ISO/IEC 7816, these data objects will be incorporated into this document at the next revision. Interindustry data objects from other standards for such data objects, an amendment to this document will be required and this will be subject to the normal ISO/IEC JTC 1 voting procedu
45、res. Following successful ballot the data objects will be incorporated into this document. 6 Specific interindustry data elements According to its needs, any application may use the following interindustry data elements and templates. 6.1 Name of an individual Referenced by tag 5B, this interindustr
46、y data element consists of up to 39 bytes; each byte is a character as defined in ISO/IEC 7501-17. The data element consists of surname, i.e., family name, given name(s), i.e., forename(s), name suffix, e.g., Jr., number, and filler(s), all coded according to ISO/IEC 8859-112. National languages wit
47、h non-Latin characters shall be transliterated or transcribed into the Latin alphabet using the appropriate ISO standard. In cases where names cannot be shown in full or a special alphabet is needed or the transliteration or transcription is not sufficient, the qualified name template should be used. a alphabetic character n s special character an alphanumeric character n.3 means one, two or three binary-coded decimal digits; BS ISO/IEC 7816-6:2004 Copyright British Standards Institution Provided by IHS under license with BSI -