《BS-EN-60983-1996 IEC-60983-1995.pdf》由会员分享，可在线阅读，更多相关《BS-EN-60983-1996 IEC-60983-1995.pdf（54页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 60983:1996 IEC 983:1995 Specification for Miniature lamps ICS 29.140.20 Incorporating Amendment No. 1 The European Standard EN 60983:1996, with the incorporation of amendment A1:2005, has the status of a British Standard Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 10 1
2、6:28:31 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 60983:1996 This British Standard, having been prepared under the direction of the Consumer Products and Services Sector Board, was published under the authority of the Standards Board and comes into effect on 15 November 1996 BSI 2006 ISBN 0 5
3、80 26198 0 National foreword The preparation of this British Standard was entrusted to Technical Committee CPL/34/1, Electric lamps, upon which the following bodies were represented: British Lighting Association for the Preparation of Standards (BRITLAPS) Chartered Institution of Building Services E
4、ngineers Electricity Association Engineering Equipment and Materials Users Association Institution of Lighting Engineers Lighting Industry Federation Ltd. London Regional Transport National Illumination Committee of Great Britain Society of Motor Manufacturers and Traders Limited Amendments issued s
5、ince publication Amd. No. DateComments 1580731 July 2006See national foreword Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 10 16:28:31 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 60983:1996 i Contents Page Committees responsibleInside front cover National forewordii Foreword2 Text of EN
6、609833 List of referencesInside back cover BSI 2006 Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 10 16:28:31 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 60983:1996 ii National foreword Section four of this standard, Lamps for miners caplights, supersedes BS 535:1987 Light sources for min
7、ers portable electric lamps, which is withdrawn. To facilitate updating, the data sheets in this standard do not carry page numbers but appear in numerical order according to the IEC reference code which appears at the foot of each sheet. In this code, the first set of digits represents the number o
8、f the IEC base document followed by the letters “IEC”; the second set represents the data sheet number and the third digit represents the edition number. Compliance with a British Standard does not of itself confer immunity from legal obligations. Cross-references Publication referred toCorrespondin
9、g British Standard EN 50033:1991BS EN 50033:1991 Specification for construction and testing of miners caplamps in relation to the risk of explosion, for mines susceptible to firedamp BS EN 60061 Specification for lamp caps and holders together with gauges for the control of interchangeability and sa
10、fety EN 60061-1:1993 (IEC 61-1:1969) BS EN 60061-1:1993 Lamp caps HD 494 S4:1994 (IEC 809) BS 6737:1986 Specification for dimensional, electrical and luminous requirements for lamps for road vehicles BS 6001 Sampling procedures for inspection by attributes ISO 2859-1:1989Part 1:1991 Specification fo
11、r sampling plans indexed by acceptable quantity level (AQL) for lot-by-lot inspection Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, the EN title page, pages 2 to 48, an inside back cover and a back cover. This standard has been updated (see copyright
12、date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. This British Standard has been prepared by Technical Committee CPL/34/1 and is the English language version of EN 60983:1996 Miniature lamps, including amendment A1:2005, publishe
13、d by the European Committee for Electrotechnical Standardization (CENELEC). It is identical with IEC 983:1995, including amendment 1:2005, published by the International Electrotechnical Commission (IEC). The amendment by which each page of the European standard was introduced is indicated by an ext
14、ension to the shoulder heading at the top of the page (e.g. EN 60061-2 : 1993/A24 : 2001. Where no such extension appears, the page is part of the original European standard. BSI 2006 This publication does not purport to include all the necessary provisions of a contract. Users are responsible for i
15、ts correct application. Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 10 16:28:31 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 60983 April 1996 ICS 29.140.20 Descriptors: Lighting equipment, lamp, halogen lamp, minature lamp, definition, elect
16、rical characteristics, photometric characteristics, dimension, interchangeability, dimensional tolerances, life, mechanical strength English version Miniature lamps (IEC 60983:1995) Lampes miniatures (CEI 60983:1995) Kleinlampen (IEC 60983:1995) This European Standard was approved by CENELEC on 1996
17、-03-05. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be o
18、btained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the C
19、entral Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United King
20、dom. CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels 1996 Copyright reserved to CENELEC members Ref. No. EN 60983:1996 E + A1 Apri
21、l 2005 Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 10 16:28:31 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 60983:1996 2 Page 2 Scope 3 Normative references3 Definitions 3 Marking 4 Requirements and tests4 Data sheets 4 Recommended instructions for the use of 4 Scope5 Definitions5 Marking 5
22、 Technical requirements and test 5 2.5 Data sheets: Road vehicle lamps6 Section 3. Torch lamps 3.1 Scope20 3.2 Definitions20 3.3 Marking20 3.4 Technical requirements20 3.5 Data sheets: Lamps for torches 21 Section 4. Lamps for miners caplights 4.1Scope28 4.2Definitions28 4.3 Requirements28 4.4 Sampl
23、ing test quantities29 4.5 Test methods30 4.6 Compliance requirements 30 4.7 Conditions of compliance31 4.8 Data sheets: Lamps for miners caplights 32 Annex A (normative) Auxiliary lamps44 Annex B (informative) Statistical basis of the tests 44 Annex ZA (normative) Normative references to internation
24、al publications with their corresponding European publications45 Table 131 Table 2 Ageing31 Table 3 Current or luminous flux31 Table 4 Current and luminous flux31 Table 531 Foreword to amendment A1 Foreword to amendment A1 The text of document 34A/1123/FDIS, future amendment 1 to IEC 60983:1995, pre
25、pared by SC 34A, Lamps, of IEC TC 34, Lamps and related equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as amendment A1 to EN 60983:1996 on 2005-04-01. The following dates were fixed: latest date by which the amendment has to be implemented at national level by
26、publication of an identical national standard or by endorsement (dop) 2006-01-01 latest date by which the national standards conflicting with the amendment have to be withdrawn (dow) 2008-04-01 Endorsement notice The text of amendment 1:2005 to the International Standard IEC 60983:1995 was approved
27、by CENELEC as an amendment to the European Standard without any modification. Foreword The text of the International Standard IEC 983:1995, prepared by SC 34A, Lamps, of IEC TC 34, Lamps and related equipment, was submitted to the Unique Acceptance Procedure and was approved by CENELEC as EN 60983 o
28、n 1996-03-05 without any modification. The following dates were fixed: Annexes designated “normative” are part of the body of the standard. Annexes designated “informative” are given for information only. In this standard, Annex A and Annex ZA are normative and Annex B is informative. Annex ZA has b
29、een added by CENELEC. latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement(dop) 1997-03-01 latest date by which the national standards conflicting with the EN have to be withdrawn(dow) 1997-03-01 BSI 2006 Licensed Copy
30、: sheffieldun sheffieldun, na, Fri Nov 10 16:28:31 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 3 Section 1. General 1.3 Definitions For the purposes of this International Standard, the following definitions apply. 1.3.1 lamp (incandescent) source made in order to produce light by means of an element
31、heated to incandescence by the passage of an electric current A combination of IEV 845-07-03 and IEV 845-07-04. 1.3.2 tungsten halogen lamp gas-filled lamp containing halogens or halogen compounds, the filament being tungsten IEV 845-07-10 1.3.3 nominal voltage voltage used to designate a lamp 1.3.4
32、 nominal wattage wattage used to designate a lamp 1.3.5 test voltage voltage for which some characteristics of a lamp are specified and at which they shall be tested 1.3.6 rated value quantity value for specified operating conditions of a component, device or equipment assigned by a manufacturer or
33、specified in a product standard 1.3.7 tolerance allowable variation from a specified value, generally expressed in per cent of this value 1.3.8 limit value lowest and/or highest value for characteristics a lamp has to comply with when operated under test conditions 1.3.9 Initial readings photometric
34、 and electrical values measured at the end of the ageing period 1.3.10 ageing period period of time for which an unused lamp is operated in order to stabilize its photometric and electrical characteristics 1.3.11 life the total time for which a lamp has been operated before it becomes useless, or is
35、 considered to be so, according to specific criteria. IEV 845-07-61 NOTELamp life is normally expressed in hours. 1.1 Scope This International Standard specifies requirements for miniature halogen and non-halogen lamps with a nominal voltage up to 30 V and a nominal wattage up to 25 W. It covers: la
36、mps to be used in road vehicles not subject to regulation and which therefore are not included in IEC 60809 (section 2); lamps for electric torches (section 3); lamps for miners caplights (section 4). Aircraft lamps are standardized in IEC 60434. This standard specifies dimensional, electrical and p
37、hotometric requirements as well as requirements concerning life and mechanical strength. NOTE Requirements are for production lamps. Individual lamps might not be completely within these requirements. Where conditions of compliance are required, they are specified in the relevant section. For some o
38、f the requirements given in this standard, reference is made to “the relevant lamp data sheet”. For some lamps these data sheets are contained in this standard. For other lamps, falling under the scope of this standard, the relevant data are supplied by the lamp manufacturer or responsible vendor. T
39、his Standard may also be used for future developments, e.g. where the light is produced by light emitting diodes (LED). 1.2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undate
40、d references, the latest edition of the referenced document (including any amendments) applies. IEC 6050-845:1987, International Electrotechnical Vocabulary (IEV) Chapter 845: Lighting EC 60061-1:1969, Lamp caps and holders together with gauges for the control of interchangeability and safety Part 1
41、: Lamp caps IEC 60434:1973, Aircraft electrical filament lamps Amendment No. 1 (1981), Amendment No. 2 (1984) IEC 60809:1985, Lamps for road vehicles Dimensional, electrical and luminous requirements Amendment No. 1 (1987), Amendment No. 2 (1989), Amendment No. 3 (1992) ISO 2859: Sampling procedures
42、 for inspection by attributes EN 50033, Electrical apparatus for potentially explosive atmospheres Caplights for mines susceptible to firedamp European standards EN 60983 : 1996/A1 : 2005 BSI 2006 Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 10 16:28:31 GMT+00:00 2006, Uncontrolled Copy, (c)
43、BSI EN 60983:1996 4 1.3.12 average life arithmetic mean of a number of individual life test results for lamps of the same type 1.3.13 truncated average life arithmetic mean of a number of individual life test results, where the test for the purpose of this calculation is considered to be terminated
44、after a predetermined period 1.3.14 lumen maintenance ratio of the luminous flux of a lamp at a given time in its life to its initial luminous flux, the lamp being operated at test voltage. IEV 845-07-65, modified NOTEThe ratio is generally expressed in per cent. 1.3.15 reference plane plane defined
45、 with reference to the cap or base and with respect to which the position of certain parts of the lamp are measured 1.3.16 reference axis axis defined with reference to the cap or base and with respect to which the position of certain parts of the lamp are measured 1.3.17 light centre length (LCL) d
46、istance between the centre of the rectangle enclosing the luminous filament section or a defined point of the filament and the reference plane 1.3.18 type lamps which differ in such essential characteristics as voltage, wattage or bulb design form different types. They are specified on the same lamp
47、 data sheet by different type numbers, e.g. 983-IEC-2251 and 983-IEC-2252 on lamp data sheet 983-IEC-2250 1.4 Marking Each lamp shall be legibly and durably marked with an identification to ensure correct replacement. Details for marking requirements and compliance conditions are specified in each s
48、ection 1.5 Requirements and tests 1.5.1 Lamp dimensions The outer lamp dimensions and the light centre length shall comply with the requirements specified on the relevant lamp data sheet. 1.5.2 Bulbs Bulbs shall not contain scores or spots which might impair the optical performance of the lamp. 1.5.
49、3 Caps Caps shall comply with the requirements specified on the relevant standard sheet(s) of IEC 61. Further requirements are specified in the relevant sections of this standard. 1.6 Data sheets 1.6.1 Numbering system for data sheets and lamps The first number represents the number of this standard “983” followed by the letters “IEC”. The second number consists of a four-digit group. The first digit represents the relevant section of this standard, the second and third digits represent the sheet ide