《BS-EN-ISO-1307-2008.pdf》由会员分享，可在线阅读，更多相关《BS-EN-ISO-1307-2008.pdf（12页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS EN ISO 1307:2008 Rubber and plastics hoses Hose sizes, minimum and maximum inside diameters, and tolerances on cut-to-length hoses ICS 23.040.70 ? Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not
2、for Resale, 08/14/2008 21:39:54 MDTNo reproduction or networking permitted without license from IHS -,-,- BS EN ISO 1307:2008 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 29 February 2008 BSI 2008 ISBN 978 0 580 55218 2 National foreword T
3、his British Standard is the UK implementation of EN ISO 1307:2008. It is identical to ISO 1307:2006. It supersedes BS EN ISO 1307:1996 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee PRI/66, Rubber and plastics tubing, hoses and hose assemblies. A lis
4、t of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from leg
5、al obligations. Amendments/corrigenda issued since publication DateComments Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 21:39:54 MDTNo reproduction or networking permitted without license
6、from IHS -,-,- EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 1307 January 2008 ICS 23.040.70Supersedes EN ISO 1307:1995 English Version Rubber and plastics hoses - Hose sizes, minimum and maximum inside diameters, and tolerances on cut-to-length hoses (ISO 1307:2006) Tuyaux en caoutchouc
7、et en plastique - Dimensions des tuyaux, diamtres intrieurs minimaux et maximaux, et tolrances sur la longueur de coupe (ISO 1307:2006) Gummi- und Kunststoffschluche - Schlauchmae, Kleinst- und Grt-Innendurchmesser, und Toleranzen bei abgelngten Schluchen (ISO 1307:2006) This European Standard was a
8、pproved by CEN on 26 December 2007. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nat
9、ional standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and
10、 notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembour
11、g, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2008 CENAll rights
12、of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 1307:2008: E Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 21:39:54 MDTNo reproducti
13、on or networking permitted without license from IHS -,-,- Foreword The text of ISO 1307:2006 has been prepared by Technical Committee ISO/TC 45 “Rubber and rubber products” of the International Organization for Standardization (ISO) and has been taken over as EN ISO 1307:2008 by Technical Committee
14、CEN/TC 218 “Rubber and plastics hoses and hose assemblies“, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by July 2008, and conflicting national standards s
15、hall be withdrawn at the latest by July 2008. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 1307:199
16、5. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Ital
17、y, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 1307:2006 has been approved by CEN as EN ISO 1307:2008 without any modifications. BS EN ISO 1307:2008 Cop
18、yright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 21:39:54 MDTNo reproduction or networking permitted without license from IHS -,-,- Reference number ISO 1307:2006(E) INTERNATIONAL STANDARD ISO 130
19、7 Fourth edition 2006-09-15 Rubber and plastics hoses Hose sizes, minimum and maximum inside diameters, and tolerances on cut-to-length hoses Tuyaux en caoutchouc et en plastique Diamtres nominaux, diamtres intrieurs minimaux et maximaux, et tolrances sur la longueur de coupe BS EN ISO 1307:2008 Cop
20、yright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 21:39:54 MDTNo reproduction or networking permitted without license from IHS -,-,- ii Copyright British Standards Institution Provided by IHS under
21、 license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 21:39:54 MDTNo reproduction or networking permitted without license from IHS -,-,- iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodi
22、es (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations
23、, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the IS
24、O/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the
25、member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 1307 was prepared by Technical Committee ISO/TC 45, Rubber and rubb
26、er products, Subcommittee SC 1, Hoses (rubber and plastics). This fourth edition cancels and replaces the third edition (ISO 1307:1992), which has been technically revised. The revision includes classifying the hoses by type according to the manufacturing process, adding additional sizes, and changi
27、ng the inside-diameter tolerances to minimum and maximum dimensions to be consistent with the latest hose standards. BS EN ISO 1307:2008 Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 21:39:5
28、4 MDTNo reproduction or networking permitted without license from IHS -,-,- blank Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 21:39:54 MDTNo reproduction or networking permitted without li
29、cense from IHS -,-,- 1 Rubber and plastics hoses Hose sizes, minimum and maximum inside diameters, and tolerances on cut-to-length hoses 1 Scope This International Standard specifies the sizes of rubber and plastics hoses and the minimum and maximum inside diameters permitted for each hose size. For
30、 this purpose, hoses are divided into four types according to the process by which they are manufactured. The standard also specifies tolerances on cut-to-length rubber and plastics hoses for industrial and automotive applications. This standard is intended to be used with the relevant hoses product
31、 standard unless there is justification for using a different hose size or unless a hose size needs a different inside-diameter range for a particular application. 2 Hose sizes and ID tolerances by manufacturing type The sizes of rubber and plastic hoses and their respective inside-diameter ranges s
32、hall be in accordance with Table 1. Four types are specified, according to the process used to manufacture them: type A: hoses built using a rigid mandrel for inside-diameter control; type B: hoses built using a flexible mandrel for inside-diameter control (plus plastic hydraulic hoses made with or
33、without a mandrel); type C: hoses built without using a mandrel (non-mandrel-built); type D: flexible extruded plastics hoses (type D does not include spiral-reinforced plastics suction and discharge hoses, which are classified as type C). BS EN ISO 1307:2008 Copyright British Standards Institution
34、Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 21:39:54 MDTNo reproduction or networking permitted without license from IHS -,-,- 2 Table 1 Hose sizes and inside-diameter tolerances Minimum and maximum inside-diameters mm Type A Bu
35、ilt on rigid mandrel Type B Built on flexible mandrel Type C Non-mandrel-built (standard tolerance) Type D Extruded plastic Non-mandrel-built (tight tolerance) Nominal size min. max. min. max. min. max. min. max. 3,2 3,2 3,8 N/A N/A N/A N/A 3,0 3,4 4 4,0 4,8 4,0 4,8 3,4 4,6 3,7 4,3 5 4,6 5,4 4,6 5,4
36、 4,2 5,4 4,7 5,3 6,3 6,2 7,0 6,2 7,0 5,6 7,2 6,0 6,6 8 7,7 8,5 7,7 8,5 7,2 8,8 7,7 8,3 10 9,3 10,1 9,3 10,1 8,7 10,3 9,7 10,3 12,5 12,3 13,5 12,3 13,5 11,9 13,5 12,2 12,8 16 15,5 16,7 15,5 16,7 15,1 16,7 15,7 16,3 19 18,6 19,8 18,6 19,8 18,3 19,9 18,4 19,6 20 19,6 20,8 19,6 20,8 19,3 20,9 N/A N/A 25
37、 25,0 26,4 25,0 26,4 24,2 26,6 24,4 25,6 31,5 31,4 33,0 31,4 33,0 30,2 33,4 30,9 32,1 38 37,7 39,3 37,7 39,3 36,5 39,7 37,4 38,6 40 39,7 41,3 39,7 41,3 38,5 41,7 N/A N/A 50 49,4 51,0 N/A N/A 48,1 51,6 N/A N/A 51 50,4 52,0 N/A N/A 49,1 52,6 50,2 51,8 63 63,1 65,1 N/A N/A 61,5 65,5 62,2 63,8 76 74,6 7
38、7,8 N/A N/A 74,2 78,2 75,0 77,0 80 78,6 81,8 N/A N/A 78,2 82,2 N/A N/A 90 87,3 90,5 N/A N/A N/A N/A N/A N/A 100 100,0 103,2 N/A N/A 99,4 103,9 N/A N/A 125 125,4 128,6 N/A N/A 124,8 129,3 N/A N/A 150 150,4 154,4 N/A N/A 150,2 154,7 N/A N/A 160 N/A N/A N/A N/A 162,9 167,4 N/A N/A 200 200,7 205,7 N/A N
39、/A 200,2 206,2 N/A N/A 250 251,0 257,0 N/A N/A 251,0 257,0 N/A N/A 305 301,8 307,8 N/A N/A 301,8 307,8 N/A N/A 315 314,5 320,5 N/A N/A N/A N/A N/A N/A 350 N/A N/A N/A N/A 351,6 359,6 N/A N/A 400 N/A N/A N/A N/A 402,4 410,4 N/A N/A N/A = Not available. BS EN ISO 1307:2008 Copyright British Standards
40、Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 21:39:54 MDTNo reproduction or networking permitted without license from IHS -,-,- 3 3 Tolerances on length The tolerances on cut-to-length hoses shall be in accordance wit
41、h Table 2. Table 2 Tolerances on cut lengths of hose Length mm Tolerance u 300 3 mm 300 but u 600 4,5 mm 600 but u 900 6 mm 900 but u 1 200 9 mm 1 200 but u 1 800 12 mm 1 800 1 % BS EN ISO 1307:2008 Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Li
42、censee=Boeing Co/5910770001 Not for Resale, 08/14/2008 21:39:54 MDTNo reproduction or networking permitted without license from IHS -,-,- BS EN ISO 1307:2008 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing Brit
43、ish Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is
44、the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front c
45、over. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should
46、be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been
47、published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-. Subscribing members of BSI are kept up to date with standards developments