《BS-EN-ISO-11124-2-1997 BS-7079-E2-1994.pdf》由会员分享，可在线阅读，更多相关《BS-EN-ISO-11124-2-1997 BS-7079-E2-1994.pdf（14页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD CONFIRMED DECEMBER 1998 BS EN ISO 11124-2:1997 BS 7079-E2: 1994 Incorporating Amendment No. 1 to BS 7079-E2:1994 (renumbers BS as BS EN ISO 11124-2: 1997) Preparation of steel substrates before application of paints and related products Specifications for metallic blast-cleaning abr
2、asives Part 2: Chilled-iron grit The European Standard EN ISO 11124-2:1997 has the status of a British Standard ICS 25.220.10; 87.020 BS EN ISO 11124-2:1997 This British Standard, having been prepared under the direction of the Surface Treatments and Coatings Standards Policy Committee was published
3、 under the authority of the Standards Board and comes into effect on 15 March 1994 BSI 04-2000 The following BSI references relate to the work on this standard: Committee reference STC/21 Draft for comment 92/50231 DC ISBN 0 580 22895 9 Committees responsible for this British Standard The preparatio
4、n of this British Standard was entrusted by the Surface Treatments and Coatings Standards Policy Committee (STC/-) to Technical Committee STC/21, upon which the following bodies were represented: Association of Consulting Engineers British Chemical Engineering Contractors Association British Coating
5、s Federation Ltd. British Constructional Steelwork Association Ltd. British Grit Association British Railways Board British Steel Industry Department of Transport Electricity Association Institute of Corrosion National Federation of Painting and Decorating Contractors Oil and Colour Chemists Associa
6、tion Paint Research Association Royal Society of Chemistry Amendments issued since publication Amd. No.DateComments 9721November 1997 Indicated by a sideline in the margin BS EN ISO 11124-2:1997 BSI 04-2000i Contents Page Committees responsibleInside front cover National forewordii Foreword2 1Scope3
7、 2Normative references3 3Definitions3 4Designation of abrasives4 5Sampling4 6Requirements for chilled-iron grit abrasives4 7Package identification and lot traceability4 8Information to be provided by the manufacturer or supplier4 Annex A (informative) Approximately equivalent codings for shot and gr
8、it abrasives7 Annex B (informative) Bibliography8 Annex ZA (normative) Normative references to international publications with their relevant European publicationsInside back cover Table 1 Screening specifications by grade Chilled-iron grit Cumulative % retained5 Table 26 Table A.17 BS EN ISO 11124-
9、2:1997 ii BSI 04-2000 National foreword This British Standard has been prepared by Technical Committee STC/21 and is the English language version of EN ISO 11124-2:1997 Preparation of steel substrates before application of paints and related products Specifications for metallic blast-cleaning abrasi
10、ves Part 2: Chilled-iron grit, published by the European Committee for Standardization (CEN). It is identical with ISO 11124-2:1993, published by the International Organization for Standardization (ISO). International Standard ISO 11124-2 was prepared by Technical Committee ISO/TC 35, Paints and var
11、nishes, Subcommittee SC 12. Preparation of steel substrates before application of paints and related products. The other parts of BS EN ISO 11124 are: Part 1: General introduction and classification; Part 3: High-carbon cast-steel shot and grit; Part 4: Low-carbon cast-steel shot. Cross-references T
12、he British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A
13、ttention is drawn to Annex ZA, which gives the European Standards that correspond to the International Standards referred to. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Complianc
14、e with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, the EN ISO title page, pages 2 to 8, an inside back cover and a back cover. This standard has been updated (see copyrigh
15、t date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 11124-2 June 1997 ICS 87.020 Descriptors: Paints, varnishes, substrates, steel products, blast-cleaning, abrasives, meta
16、llic abrasives, specifications, designation English version Preparation of steel substrates before application of paints and related products Specifications for metallic blast-cleaning abrasives Part 2: Chilled-iron grit (ISO 11124-2:1993) Prparation des subjectiles dacier avant application de peint
17、ures et de produits assimils Spcifications pour abrasifs mtalliques destins la prparation par projection Partie 2: Grenaille angulaire (ISO 11124-2:1993) Vorbereitung von Stahloberflchen vor dem Auftragen von Beschichtungsstoffen Anforderungen an metallische Strahlmittel Teil 2: Hartgu, kantig (Grit
18、) (ISO 11124-2:1993) This European Standard was approved by CEN on 1997-05-28. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bib
19、liographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility
20、of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands,
21、Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1997 CEN All rights of exploitation in any form and by any means reserved
22、 worldwide for CEN national Members. Ref. No. EN ISO 11124-2:1997 E EN ISO 11124-2:1997 BSI 04-2000 2 Foreword The text of the International Standard from Technical Committee ISO/TC 35, Paints and varnishes, of the International Organization for Standardization (ISO) has been taken over as a Europea
23、n Standard by Technical Committee CEN/TC 139, Paints and varnishes, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 1997, and conflicting national
24、 standards shall be withdrawn at the latest by December 1997. According to CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Ice
25、land, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. NOTENormative references to International Standards are listed in Annex ZA (normative). EN ISO 11124-2:1997 BSI 04-20003 WARNING Equipment, materials and abrasives used for surface pre
26、paration can be hazardous if used carelessly. Many national regulations exist for those materials and abrasives that are considered to be hazardous during or after use (waste management), such as free silica or carcinogenic or toxic substances. These regulations are therefore to be observed. It is i
27、mportant to ensure that adequate instructions are given and that all required precautions are exercised. 1 Scope This part of ISO 11124 specifies requirements for 12 grades of chilled-iron grit abrasives, as supplied for blast-cleaning processes. It specifies ranges of particle sizes, together with
28、corresponding grade designations. Values are specified for hardness, density, defect/structural requirements and chemical composition. The requirements specified in this part of ISO 11124 apply to abrasives supplied in the “new” condition only. They do not apply to abrasives either during or after u
29、se. Test methods for metallic blast-cleaning abrasives are given in the various parts of ISO 11125. Chilled-iron grit abrasives are used in both static and site blasting equipment. They are most often selected where a facility exists for recovery and re-use of the abrasive. NOTE 1Information on comm
30、only referenced national standards for metallic abrasives and their approximate relationship with ISO 11124 is given in Annex A and Annex B. NOTE 2Although this part of ISO 11124 has been developed specifically to meet requirements for preparation of steelwork, the properties specified will generall
31、y be appropriate for use when preparing other material surfaces, or components, using blast-cleaning techniques. These techniques are described in ISO 8504-2:1992, Preparation of steel substrates before application of paints and related products Surface preparation methods Part 2: Abrasive blast-cle
32、aning. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this part of ISO 11124. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on th
33、is part of ISO 11124 are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO maintain registers of currently valid International Standards. ISO 9556:1989, Steel and iron Determination of total carbon content Infrared
34、 absorption method after combustion in an induction furnace. ISO 11125-1:1993, Preparation of steel substrates before application of paints and related products Test methods for metallic blast-cleaning abrasives Part 1: Sampling. ISO 11125-2:1993, Preparation of steel substrates before application o
35、f paints and related products Test methods for metallic blast-cleaning abrasives Part 2: Determination of particle size distribution. ISO 11125-3:1993, Preparation of steel substrates before application of paints and related products Test methods for metallic blast-cleaning abrasives Part 3: Determi
36、nation of hardness. ISO 11125-4:1993, Preparation of steel substrates before application of paints and related products Test methods for metallic blast-cleaning abrasives Part 4: Determination of apparent density. ISO 11125-5:1993, Preparation of steel substrates before application of paints and rel
37、ated products Test methods for metallic blast-cleaning abrasives Part 5: Determination of percentage defective particles and of microstructure. ISO 11125-6:1993, Preparation of steel substrates before application of paints and related products Test methods for metallic blast-cleaning abrasives Part
38、6: Determination of foreign matter. ISO 11125-7:1993, Preparation of steel substrates before application of paints and related products Test methods for metallic blast-cleaning abrasives Part 7: Determination of moisture. 3 Definitions For the purposes of this part of ISO 11124, the following defini
39、tions apply. 3.1 chilled-iron shot a metallic blast-cleaning abrasive produced by a casting process in which molten iron is formed into shot (see also 3.3) by means of an atomization process 3.2 chilled-iron grit a metallic blast-cleaning abrasive obtained by crushing various chilled iron-shot sizes
40、 into sharp-edged angular particles NOTE 3Chilled-iron shot may also be used as a blast-cleaning abrasive but is not included in this part of ISO 11124. 3.3 shot particles that are predominantly round, that have a length of less than twice the maximum particle width and that do not have edges, broke
41、n faces or other sharp surface defects EN ISO 11124-2:1997 4 BSI 04-2000 3.4 grit particles that are predominantly angular, that have fractured faces and sharp edges and that are less than half-round in shape 3.5 defect A fault or weakness in an abrasive which, if present at or above a given level,
42、may be detrimental to the performance of the abrasive (see Table 2). 3.5.1 void a smooth-surfaced internal cavity considered undesirable when greater than 10 % of the cross-sectional area of a particle 3.5.2 shrinkage defect an internal cavity with a rough dendritic surface or a zone of microporosit
43、y, considered undesirable when greater than 40 % of the cross-sectional area of a particle 3.5.3 crack a linear discontinuity that has a length-to-width ratio of 3 : 1 or greater, that extends over more than 20 % of the diameter or shortest dimension of a particle and that is radial in direction 3.6
44、 foreign matter any material or particles mixed with the abrasive which are not attached to the abrasive particles and which are nonmagnetic 4 Designation of abrasives Chilled-iron abrasives shall be identified by “Abrasive ISO 11124” and the abbreviation “M/CI” indicating metallic, chilled-iron abr
45、asive. The symbol “G” shall follow to indicate the required particle shape of the grit as purchased. The designation shall be completed by a 3-digit number denoting the grade, or nominal particle size, required. EXAMPLE 1 Abrasive ISO 11124 M/CI/G100 denotes an abrasive of the metallic, chilled-iron
46、 type, complying with the requirements of this part of ISO 11124, of particle shape grit and of grade 100 (i.e. nominal particle size 1,00 mm). It is essential that this full product designation is quoted on all orders. NOTE 4Grade requirements and codes are specified in Table 1. The grade code is b
47、ased on a number indicating the approximate middle of the particle size range, or nominal diameter, for each grade, expressed in millimetres 100. NOTE 5Annex A provides guidance on approximately equivalent grades and codings in other commonly referenced national standards for cast-metal abrasives. 5
48、 Sampling Sampling procedures shall be as specified in ISO 11125-1. 6 Requirements for chilled-iron grit abrasives The requirements for chilled-iron grit abrasives shall be as specified in Table 2. 7 Package identification and lot traceability All supplies shall be clearly marked and identified usin
49、g the designation specified in clause 4. The unit of sale, i.e. pallet, drum, box, etc., shall be clearly labelled with the full product coding. Sub-units, i.e. bags, shall be marked with the particle shape and grade codes. NOTE 6Inclusion of additional marking to allow product traceability to a particular production period or lot is strongly recommended. Traceability references should be included at least at the pallet, drum or box level of package marking. 8 Information to be provided b