《BS-EN-60335-2-2-1996.pdf》由会员分享，可在线阅读，更多相关《BS-EN-60335-2-2-1996.pdf（22页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 60335-2-2:1996 Incorporating Amendments Nos. 1 and 2 Safety of household and similar electrical appliances Part 2-2: Particular requirements for vacuum cleaners and water suction cleaning appliances The European Standard EN 60335-2-2:1995 with the incorporation of amendments A
2、1:1998 and A2:2000 has the status of a British Standard ICS 97.080 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 13 17:48:21 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 60335-2-2:1996 This British Standard, having been
3、 prepared under the direction of the Electrotechnical Sector Board, was published under the authority of the Standards Board and comes into effect on 15 March 1996 BSI 04-2001 The following BSI references relate to the work on this standard: Committee reference CPL/61 Draft for comment 92/31440 DC I
4、SBN 0 580 25240 X Committees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee CPL/61, Safety of electrical appliances, upon which the following bodies were represented: Agricultural Engineers Association Association of Consulting Sci
5、entists Association of Control Manufacturers TACMA (BEAMA Ltd.) Association of Manufacturers of Domestic Electrical Appliances British Cable Makers Confederation British Electrotechnical Approvals Board British Pest Control Association British Retail Consortium CESA (the Association of Catering Equi
6、pment Manufacturers and Importers) Consumer Policy Committee of BSI Consumers Association Department of Trade and Industry (Consumer Safety Unit, CA Division) ERA Technology Ltd. Electrical Installation Equipment Manufacturers Association (BEAMA Ltd.) Electricity Association Health and Safety Execut
7、ive Industrial Cleaning Machine Manufacturers Association (BEAMA Ltd.) Institute of Trading Standards Administration Institution of Electrical Engineers Loss Prevention Council Ministry of Defence Portable Electric Tool Manufacturers Association Rotating Electrical Machines Association (BEAMA Ltd.)
8、Royal Society for the Prevention of Accidents Small Electrical Appliances Marketing Association The following body was also represented in the drafting of the standard, through subcommittees and panels: Department of Health Amendments issued since publication Amd. No.Date of issueComments 10020May 1
9、999See national foreword 11059April 2001See national foreword Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 13 17:48:21 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 60335-2-2:1996 BSI 04-2001 i Contents Page Committees responsibleInside front cover National forewordii Foreword2 Text of EN
10、60335-2-25 National annex NA (informative) Original IEC text amended by CENELEC common modifications17 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 13 17:48:21 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 60335-2-2:1996 ii BSI 04-2001 National foreword This British Standard has been prepa
11、red by Technical Committee CPL/61 and is the English language version of EN 60335-2-2:1995, including amendments A1:1998 and A2:2000 and corrigendum April 2000, published by the European Committee for Electrotechnical Standardization (CENELEC). It was derived from IEC 60335-2-2:1993 (fourth edition)
12、, including amendments 1:1998 and 2:1999, published by the International Electrotechnical Commission (IEC), which has the same title as the European Standard. The CENELEC common modifications have been implemented at the appropriate places in the text. The start and finish of each common modificatio
13、n is indicated in the text by tags ? ?. The start and finish of text introduced or altered by amendment is indicated in the text by tags ? ?. Tags indicating changes to IEC text carry the number of the IEC amendment. For example, text altered by IEC amendment 1 is indicated by ? ?. The national diff
14、erences taken from the preface to IEC 60335-2-2:1993 and parts of the original IEC text that have been modified by CENELEC are quoted in National annex NA. NOTE Corrigendum April 2000 correct the text of 6.1, first paragraph. The foreword of EN 60335-2-2 makes reference to the date of withdrawal, do
15、w, of the relevant national standard. In this case the relevant national standard is BS 3456-202.2:1990 which will be withdrawn on 1 January 1998 in accordance with the CENELEC Internal Regulations. Certificates and marks will not be awarded after this date with regard to the withdrawn British Stand
16、ard. However, such certificates and marks, already awarded, may continue to apply to production until 1 January 2003. This British Standard is to be read in conjunction with BS EN 60335-1:1995, Specification for safety of household and similar electrical appliances Part 1: General requirements. The
17、many references to Part 1 should be read as references to BS EN 60335-1, which is the English language version of EN 60335-1:1994 which was derived from IEC publication 60335-1 (third edition 1991, second impression 1993). Amendments and revisions of Part 1 have also to be taken into account and the
18、 dates when such changes become applicable will be stated in the relevant amendment or revision of Part 1. Product approval. Attention is drawn to the fact that products conforming to this British Standard may be approved by the British Electrotechnical Approvals Board for the purposes of participat
19、ion in the CENELEC Certification Agreement and in the CB Scheme of the IECEE. (Details of the BEAB Approval Scheme are given on the inside back cover.) Cross-references Attention is drawn to the fact the CEN and CENELEC Standards normally include an annex which lists normative references to internat
20、ional publications with their corresponding European publications. The British Standards which implement these international or European publications may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility
21、 of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligation
22、s. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, the EN title page, pages 2 to 17 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 13
23、 17:48:21 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 60335-2-2 August 1995 + A1 February 1998 + A2 April 2000 ICS 97.080Supersedes EN 60335-2-2:1988 and its amendments Incorporates Corrigendum April 2000 Descriptors: Household electrical appliance
24、s, vacuum cleaners, cleaning appliances, safety requirements, protection against electric shock, fire protection, protection against mechanical hazard English version Safety of household and similar electrical appliances Part 2-2: Particular requirements for vacuum cleaners and water suction cleanin
25、g appliances (includes amendments A1:1998 and A2:2000) (IEC 60335-2-2:1993 + A1:1998 + A2:1999, modified) Scurit des appareil lectrodomestiques et analogues Partie 2-2: Rgles particulires pour les aspirateurs et les appariels de nettoyage aspiration deau (inclut les amendements A1:1998 et A2:2000) (
26、CEI 60335-2-2:1993 + A1:1998 + A2:1999, modifie) Sicherheit elektrischer Gerte fr den Hausgebrauch und hnliche Zwecke Teil 2-2: Besondere Anforderungen fr Staubsauger und Wassersauger (enthlt nderungen A1:1998 und A2:2000) (IEC 60335-2-2:1993 + A1:1998 + A2:1999, modifiziert) This European Standard
27、was approved by CENELEC on 1995-07-04. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. This European Standard exists in three official versions (En
28、glish, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. Up-to-date lists and bibliographical references concerning such nationa
29、l standards may be obtained on application to the Central Secretariat or to any CENELEC member. CENELEC members are the national electrotechnical committees of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Swed
30、en, Switzerland and United Kingdom. CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels 1995 Copyright reserved to CENELEC members Ref
31、. No. EN 60335-2-2:1995 + A1:1998 + A2:2000 E Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 13 17:48:21 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 60335-2-2:1995 BSI 04-2001 2 Foreword The proposal to endorse IEC 335-2-2:1993, document CLC/TC 61 (SEC)904, was circulated under the enquiry pr
32、ocedure in July 1993. This proposal was discussed during the Oslo meeting in April 1994, when it was decided to submit a draft for EN 60335-2-2 to the formal vote. This draft was circulated in November 1994 and was ratified by CENELEC as EN 60335-2-2 on 1995-07-04. This European Standard has been pr
33、epared by the Secretariat of CENELEC Technical Committee TC 61. The following dates are applicable: For products which have complied with EN 60335-2-2:1988 including its amendments A2:1990, A52:1991 and A53:1994 before 1998-01-01, as shown by the manufacturer or by a certification body, this previou
34、s standard may continue to apply for production until 2003-01-01. This standard has to be used in conjunction with EN 60335-1, Safety of household and similar electrical appliances Part 1: General requirements. It was established on the basis of the 1994 edition of that standard. Amendments and revi
35、sions of Part 1 have also to be taken into account and the dates when such changes become applicable will be stated in the relevant amendment or revision of Part 1. This Part 2 supplements or modifies the corresponding clauses of EN 60335-1, so as to convert it into the European Standard: Safety req
36、uirements for electric vacuum cleaners and water suction cleaning appliances. Where a particular subclause of Part 1 is not mentioned in this Part 2, that subclause applies as far as is reasonable. Where this standard states “addition”, “modification” or “replacement”, the relevant text of Part 1 is
37、 to be adapted accordingly. Subclauses and figures which are additional to those in Part 1 are numbered starting from 101. There are no special national conditions causing a deviation from this European Standard, other than those listed in Annex ZA to EN 60335-1. There are no national deviations fro
38、m this European Standard other than those listed in Annex ZB to EN 60335-1. NOTEThe following print types are used: requirements: in roman type; test specifications: in italic type; notes: in small roman type. Words in bold in the text are defined in clause 2. When a definition of Part 1 concerns an
39、 adjective, the adjective and the associated noun are also in bold. Foreword to amendment A1 The text of document 61/1342/FDIS, future amendment to IEC 60335-2-2:1993 prepared by the IEC Technical Committee 61, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as amendment A
40、1 to EN 60335-2-2 on 1998-01-01. The following dates are applicable: This amendment supplements or modifies the corresponding clauses of EN 60335-2-2:1995. There are no special national conditions causing a deviation from this amendment. There are no national deviations from this amendment. latest d
41、ate by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop)1996-01-01 latest date by which national standards conflicting with the EN have to be withdrawn(dow)1998-01-01 latest date by which the amendment has to be implemented
42、at national level by publication of an identical national standard or by endorsement(dop) 1998-10-01 date on which national standards conflicting with the amendment have to be withdrawn(dow) 2005-01-01 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 13 17:48:21 GMT+00:00 2006, Uncontrolled Copy,
43、 (c) BSI EN 60335-2-2:1995 BSI 04-2001 3 Foreword to amendment A2 The text of document 61/1642/FDIS, future amendment to IEC 60335-2-2:1993 prepared by the IEC Technical Committee 61, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as amendment A2 to EN 60335-2-2 on 1999-1
44、2-01. The following dates are applicable: This amendment supplements or modifies the corresponding clauses of EN 60335-2-2:1995. There are no special national conditions causing a deviation from this amendment. There are no national deviations from this amendment. Introduction An investigation by CE
45、NELEC TC 61 has shown that all risks from products within the scope of this standard are fully covered by the Low Voltage Directive, 73/23/EEC. If the product has mechanical moving parts, a risk assessment in accordance with the Machinery Directive, 89/392/EEC, has shown that the risks are mainly of
46、 electrical origin and consequently this directive is not applicable. However, the relevant essential safety requirements of the Machinery Directive are covered by this standard together with the principal objectives of the Low Voltage Directive. Contents Page Foreword2 1Scope5 2Definitions5 3Genera
47、l requirement6 4General conditions for the tests6 5Void6 6Classification6 7Marking and instructions6 8Protection against access to live parts7 9Starting of motor-operated appliances7 10Power input and current7 11Heating7 12Void8 13Leakage current and electric strength at operating temperature8 14Voi
48、d8 15Moisture resistance8 16Leakage current and electric strength9 17Overload protection of transformers and associated circuits9 18Endurance9 19Abnormal operation9 20Stability and mechanical hazards9 21Mechanical strength10 22Construction11 23Internal wiring11 24Components11 25Supply connection and
49、 external flexible cords11 26Terminals for external conductors12 27Provision for earthing12 28Screws and connections12 29Creepage distances, clearances and distances through insulation12 30Resistance to heat, fire and tracking12 31Resistance to rusting12 32Radiation, toxicity and similar hazards12 latest date by which the amendment has to be implemented at national level by publication of an identical national standard or by endorsement(dop) 2000-11-01 date on which national standards conflicting with the amendment have to