《BS-EN-60335-2-85-1998 IEC-60335-2-85-1997.pdf》由会员分享，可在线阅读，更多相关《BS-EN-60335-2-85-1998 IEC-60335-2-85-1997.pdf（14页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 60335-2-85: 1998 IEC 60335-2-85: 1997 Incorporating Amendment No. 1 Safety of household and similar electrical appliances Part 2-85: Particular requirements for fabric steamers The European Standard EN 60335-2-85:1998 with the incorporation of amendment A1:2000 has the status
2、of a British Standard ICS 97.060 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 13 17:46:12 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 60335-2-85:1998 This British Standard, having been prepared under the direction of
3、the Electrotechni- cal Sector Board, was published under the authority of the Standards Board and comes into effect on 15 April 1998 BSI 04-2001 ISBN 0 580 29788 8 National foreword This British Standard is the English language version of EN 60335-2-85:1998 including amendment A1:2000. It is identic
4、al with IEC 60335-2-85:1997 including amendment 1:2000. The UK participation in its preparation was entrusted by Technical Committee CPL/61, Safety of electrical appliances, to Subcommittee CPL/61/07, Safety of electrical appliances heated appliance group, which has the responsibility to: aid enquir
5、ers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations rep
6、resented on this subcommittee can be obtained on request to its secretary. From 1 January 1997, all IEC publications have the number 60000 added to the old number. For instance, IEC 27-1 has been renumbered as IEC 60027-1. For a period of time during the change over from one numbering system to the
7、other, publications may contain identifiers from both systems. Cross-references Attention is drawn to the fact that CEN and CENELEC standards normally include an annex which lists normative references to international publications with their corresponding European publications. The British Standards
8、 which implement these international or European publications may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to inclu
9、de all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN
10、 title page, pages 2 to 10, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Sidelining in this document indicates the most recent changes by amendment. Amendments issued since publication Amd. No.DateComments 120
11、28April 2001Indicated by a sideline Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 13 17:46:12 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 60335-2-85 February 1998 +A1 August 2000 ICS 97.060Descriptors: Household electrical appliances, steam a
12、ppliance, garments, safety require- ments, protection against electric shock, protection against mechanical hazard, fire protection English version Safety of household and similar electrical appliances Part 2-85: Particular requirements for fabric steamers (includes amendment A1:2000) (IEC 60335-2-8
13、5:1997 + A1:2000) Scurit des appareils lectrodomestiques et analogues Partie 2-85: Rgles particulires pour les appareils vapeur pour tissus (inclut lamendement A1:2000) (CEI 60335-2-85:1997 + A1:2000) Sicherheit elektrischer Gerte fr den Hausgebrauch und hnliche Zwecke Teil 2-85: Besondere Anforderu
14、ngen an Dampfgerte fr Stoffe (enthlt nderung A1:2000) (IEC 60335-2-85:1997 + A1:2000) This European Standard was approved by CENELEC on 1998-01-01. Amendment A1 was approved by CENELEC on 2000-04-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the co
15、nditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in
16、 three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotec
17、hnical committees of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normal
18、isation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels 1998 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60335-2-85:1998 + A1:2000 E Licensed Copy: sheff
19、ieldun sheffieldun, na, Mon Nov 13 17:46:12 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 60335-2-85:1998 BSI 04-2001 2 Foreword The text of document 61/1353/FDIS, future first edition of IEC 60335-2-85 prepared by the IEC Technical Committee 61, was submitted to the IEC-CENELEC parallel vote and wa
20、s approved by CENELEC as EN 60335-2-85 on 1998-01-01. The following dates are applicable: This standard has to be used in conjunction with EN 60335-1, Safety of household and similar electrical appliances Part 1: General requirements. It was established on the basis of the 1994 edition of that stand
21、ard. Amendments and revisions of part 1 have also to be taken into account and the dates when such changes become applicable will be stated in the relevant amendment or revision of part 1. This part 2 supplements or modifies the corresponding clauses of EN 60335-1, so as to convert it into the Europ
22、ean Standard: Safety requirements for electric fabric steamers. When a particular subclause of part 1 is not mentioned in this part 2, that subclause applies as far as is reasonable. When this standard states “addition”, “modification” or “replacement”, the relevant text of part 1 is to be adapted a
23、ccordingly. Subclauses which are additional to those in part 1 are numbered starting with 101. There are no special national conditions causing a deviation from this European Standard, other than those listed in Annex ZB to EN 60335-1. There are no national deviations from this European Standard, ot
24、her than those listed in Annex ZB to EN 60335-1. NOTEThe following print types are used: requirements: in roman type; test specifications: in italic type; notes: in small roman type. Words in bold in the text are defined in clause 2. When a definition of part 1 concerns an adjective, the adjective a
25、nd the associated noun are also in bold. Endorsement notice The text of the International Standard IEC 60335-2-85:1997 was approved by CENELEC as a European Standard without any modification. Foreword to amendment A1 The text of document 61/1762/FDIS, future amendment to IEC 60335-2-85:1997 prepared
26、 by the IEC Technical Committee 61, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as amendment A1 to EN 60335-2-85 on 2000-04-01. The following dates were fixed: This amendment supplements or modifies the corresponding clauses of EN 60335-2-85:1998. There are no special
27、national conditions causing a deviation from this amendment. There are no national deviations from this amendment. Introduction An investigation by CENELEC TC 61 has shown that all risks from products within the scope of this standard are fully covered by the Low Voltage Directive, 73/23/EEC. If the
28、 product has mechanical moving parts, a risk assessment in accordance with the Machinery Directive, 89/392/EEC, has shown that the risks are mainly of electrical origin and consequently this directive is not applicable. However, the relevant essential safety requirements of the Machinery Directive a
29、re covered by this standard together with the principal objectives of the Low Voltage Directive. Endorsement notice The text of amendment 1:2000 to the International Standard IEC 60335-2-85:1997 was approved by CENELEC as an amendment to the European Standard without any modification. latest date by
30、 which the EN has to be implemented at national level by publication of an identical national standard or by endorsement(dop) 1998-10-01 date on which national standards conflicting with the EN have to be withdrawn(dow) 2005-01-01 latest date by which the amendment has to be implemented at national
31、level by publication of an identical national standard or by endorsement(dop) 2001-01-01 date on which national standards conflicting with the amendment have to be withdrawn(dow) 2005-01-01 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 13 17:46:12 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN
32、60335-2-85:1998 BSI 04-2001 3 Contents Page Foreword2 1Scope5 2Definitions5 3General requirement5 4General conditions for the tests5 5Void6 6Classification6 7Marking and instructions6 8Protection against access to live parts6 9Starting of motor-operated appliances6 10Power input and current6 11Heati
33、ng6 12Void7 13Leakage current and electric strength at operating temperature7 14Void7 15Moisture resistance7 16Leakage current and electric strength7 17Overload protection of transformers and associated circuits7 18Endurance7 19Abnormal operation7 20Stability and mechanical hazards7 21Mechanical str
34、ength7 22Construction8 23Internal wiring8 24Components8 25Supply connection and external flexible cords8 26Terminals for external conductors9 27Provision for earthing9 28Screws and connections9 29Creepage distances, clearances and distances through insulation9 30Resistance to heat, fire and tracking
35、9 31Resistance to rusting9 32Radiation, toxicity and similar hazards9 Annexes10 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 13 17:46:12 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 4 blank Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 13 17:46:12 GMT+00:00 2006, Uncontrolled Copy, (c) BS
36、I EN 60335-2-85:1998 BSI 04-2001 5 1 Scope This clause of part 1 is replaced by: This standard deals with the safety of electric fabric steamers intended for household and similar purposes, their rated voltage being not more than 250 V. Appliances not intended for normal household use, but which nev
37、ertheless may be a source of danger to the public, such as appliances intended to be used by laymen in shops, are within the scope of this standard. NOTE 1Examples of such appliances are those for use in laundries and dry cleaners. So far as is practicable, this standard deals with the common hazard
38、s presented by appliances which are encountered by all persons in and around the home. This standard does not in general take into account: the use of appliances by young children or infirm persons without supervision; playing with the appliance by young children. NOTE 2Attention is drawn to the fac
39、t that: for appliances intended to be used in vehicles or on board ships or aircraft, additional requirements may be necessary; for appliances intended to be used in tropical countries special requirements may be necessary; in many countries additional requirements are specified by the national heal
40、th authorities, the national authorities responsible for the protection of labour and similar authorities. NOTE 3This standard does not apply to: appliances intended to be used in locations where special conditions prevail, such as the presence of a corrosive or explosive atmosphere (dust, vapour or
41、 gas); electric irons (IEC 60335-2-3); electric ironers (IEC 60335-2-44); appliances connected to the water mains. 2 Definitions This clause of part 1 is applicable except as follows: 2.2.6 Addition: NOTE For electrode-type appliances, if no current is assigned to the appliance, the rated current is
42、 calculated from the rated voltage and the mean value of the power input during the first 2 min of operation, the appliance being supplied at rated voltage and operating under normal operation. 2.2.9 Replacement: normal operation operation of the appliance in the normal position of use but away from
43、 any surface, with the container filled with water and with any lid closed for electrode-type appliances, the water has a resistivity of approximately 500?cm at 20?C 5?C NOTEThe appropriate resistivity may be obtained by adding sodium chloride to the water. 2.101 fabric steamer appliance for removin
44、g creases from garments and fabrics by directing steam at their surface 2.102 electrode-type appliance appliance in which a conductive liquid is heated by a current flowing through it 3 General requirement This clause of part 1 is applicable. 4 General conditions for the tests This clause of part 1
45、is applicable. Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 13 17:46:12 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 60335-2-85:1998 6 BSI 04-2001 5 Void 6 Classification This clause of part 1 is applicable except as follows: 6.1 Addition: Electrode-type appliances and appliances with bare h
46、eating elements shall be of class I, class II or class III. 7 Marking and instructions This clause of part 1 is applicable except as follows: 7.1 Modification: Electrode-type appliances shall be marked with their rated power input. 7.12 Addition: The instructions for use shall include information wi
47、th regard to: the composition and quantity of solution to be used, with a warning against the excessive use of salt, if applicable; filling, cleaning and descaling, if applicable. The instructions shall include: a warning against the risk of scalding by steam; advice that electrode-type appliances a
48、re not to be operated from a d.c. supply; advice to unplug the appliance during filling and cleaning. The instructions for use of appliances incorporating an appliance inlet and intended to be partially or completely immersed in water for cleaning, shall state that the connector must be removed befo
49、re the appliance is cleaned and the appliance inlet dried before the appliance is used again. 8 Protection against access to live parts This clause of part 1 is applicable. 9 Starting of motor-operated appliances This clause of part 1 is not applicable. 10 Power input and current This clause of part 1 is applicable except as follows: 10.1 Addition: NOT