《BS-EN-61076-2-103-2004.pdf》由会员分享，可在线阅读，更多相关《BS-EN-61076-2-103-2004.pdf（38页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 61076-2-103:2004 Connectors for electronic equipment Part 2-103: Circular connectors Detail specification for a range of multipole connectors (type “XLR”) The European Standard EN 61076-2-103:2004 has the status of a British Standard ICS 31.220.10 ? BS EN 61076-2-103:2004 This
2、 British Standard was published under the authority of the Standards Policy and Strategy Committee on 4 June 2004 BSI 4 June 2004 ISBN 0 580 43847 3 National foreword This British Standard is the official English language version of EN 61076-2-103:2004. It is identical with IEC 61076-2-103:2004. The
3、 UK participation in its preparation was entrusted by Technical Committee EPL/48, Electromechanical components and medical equipment, to Subcommittee EPL/48/2, Connectors for electronic equipment, which has the responsibility to: A list of organizations represented on this subcommittee can be obtain
4、ed on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of
5、 the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid
6、enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This
7、 document comprises a front cover, an inside front cover, the EN title page, pages 2 to 34, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. DateComments EUROPEAN STAND
8、ARD EN 61076-2-103 NORME EUROPENNE EUROPISCHE NORM May 2004 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2004 CENELEC - All r
9、ights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 61076-2-103:2004 E ICS 31.220.10 English version Connectors for electronic equipment Part 2-103: Circular connectors Detail specification for a range of multipole connectors (type XLR) (IEC 61076-2
10、-103:2004) Connecteurs pour quipements lectroniques Partie 2-103: Connecteurs circulaires - Spcification particulire pour une gamme de connecteurs multipolaires (type XLR) (CEI 61076-2-103:2004) Steckverbinder fr elektronische Einrichtungen Teil 2-103: Rundsteckverbinder - Bauartspezifikation fr ein
11、e Reihe von mehrpoligen Rundsteckverbindern (Typ “XLR“) (IEC 61076-2-103:2004) This European Standard was approved by CENELEC on 2004-05-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a
12、national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A versi
13、on in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, Czech Republ
14、ic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EN 67016-2-01:30024 - - 2 Foreword The text of document 48B/1413/F
15、DIS, future edition 1 of IEC 61076-2-103, prepared by IEC TC 48, Electromechanical components and mechanical structures for electronic equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 61076-2-103 on 2004-05-01. The following dates were fixed: latest date by
16、 which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2005-02-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2007-05-01 _ Endorsement notice The text of the International Stand
17、ard IEC 61076-2-103:2004 was approved by CENELEC as a European Standard without any modification. _ Page 2 EN 610762103:2004 -67016-2301 4002:CEI 3 CONTENTS 1 General information 6 1.1 Scope6 1.2 Recommended method of mounting.6 1.3 Number of contacts or contact cavities.6 1.4 Ratings and characteri
18、stics6 1.5 Normative references 6 1.6 Marking .7 1.7 IEC Type designation.8 1.8 Ordering information8 2 Technical information9 2.1 Definitions .9 2.2 Survey of styles and variants .9 2.3 Information on application10 2.4 Contact arrangements .10 3 Drawings and dimensions .10 3.1 General .10 3.2 Isome
19、tric view and common features .11 3.3 Engagement (mating) information 12 3.4 Fixed connectors .17 3.5 Free connectors 19 3.6 Accessories.20 3.7 Mounting information for fixed connectors20 3.8 Assembly information for free connectors.21 3.9 Gauges .22 4 Characteristics23 4.1 Climatic category.23 4.2
20、Electrical .23 4.3 Mechanical24 5 Test schedule.25 5.1 General .25 5.2 Test schedules 28 Figure 1 Common features.11 Figure 2 Panel-mount style.11 Figure 3 Female connector.12 Figure 4 Male connector.14 Figure 5 Tip of contact pin15 Figure 6 Contact arrangements 16 Figure 7 Size 1M 17 Figure 8 Size
21、1F.17 Figure 9 Size 2.17 Figure 10 Size 3.17 Figure 11 Female straight connector.19 Page 3 EN 610762103:2004 -67016-2301 4002:CEI 4 Figure 12 Male straight connector.19 Figure 13 Female right-angle connector19 Figure 14 Male right-angle connector19 Figure 15 Male vertical pattern .20 Figure 16 Femal
22、e vertical pattern .20 Figure 17 Male horizontal pattern .20 Figure 18 Female horizontal pattern .20 Figure 19 Variant 1M21 Figure 20 Variant 1F.21 Figure 21 Variant 3.21 Figure 22 Variant 2.21 Figure 23 Plug gauge .22 Figure 24 Mating of free connectors .26 Figure 25 Mating of fixed and free connec
23、tor 26 Figure 26 Vibration testing setup 27 Table 1 Designation of first style letter9 Table 2 Designation of second style letter.9 Table 3 Closest mounting centres for each variant of “panel-mount size” 11 Table 4 Dimensions of female connector 12 Table 5 Dimensions of male connector .14 Table 6 Pi
24、n diameters 15 Table 7 Types of terminations on fixed connector .19 Table 8 Types of terminations on free connector.19 Table 9 Gauge dimensions and weights22 Table 10 Performance levels 23 Table 11 Creepage and clearance distances.23 Table 12 Contact derating 24 Table 13 Wire sizes for electrical te
25、sts .27 Table 14 Basic tests.28 Table 15 Test group P29 Table 16 Test group AP30 Table 17 Test group BP33 Table 18 Test group CP .34 Table 19 Test group DP .35 Table 20 Test group EP35 Table 21 Test group HP .36 Table 22 Test group LP36 Page 4 EN 610762103:2004 -67016-2301 4002:CEI 5 CONNECTORS FOR
26、ELECTRONIC EQUIPMENT Part 2-103: Circular connectors Detail specification for a range of multipole connectors (type XLR) INTERNATIONAL ELECTROTECHNICAL COMMISSION IEC SC 48B - Connectors IEC 61076-2-103 ELECTRONIC COMPONENTS in accordance with IEC 61076-1: Generic specification Blank detail specific
27、ation IEC 61076-2-001 A range of fixed and free circular multi-pole connectors, with common shell and mounting dimensions Fixed connectors are available in both panel and printed-board mounting versions. Also, versions are available with metal shells and others with moulded plastic shells 3 pole ver
28、sions IEC 233/04 Performance level(s): Reserved Assessment level(s): Reserved Combination of performance levels and assessment levels: Reserved Information on the availability of components qualified to this detail specification is given in the qualified products list. Page 5 EN 610762103:2004 -6701
29、6-2301 4002:CEI 6 1 General information 1.1 Scope This part of IEC 61076 applies to a range of circular multi-pole connectors with or without latching device, having a nominal outer shell diameter of 19 mm, with 3 to 7 contacts (type XLR). Fixed connectors are available in both panel-mounting and pr
30、inted-board mounting versions. These connectors are widely used in professional audio applications. This part of IEC 61076 establishes uniform specifications, type testing requirements and quality assessment procedures for a subfamily of circular connectors. It should be used in conjunction with the
31、 applicable sectional specification, see 1.1 of IEC 61076-2. 1.2 Recommended method of mounting For guidance on the application of connectors in mechanical structures, see IEC 60917-2-2. Panel-mounted fixed connectors should normally be mounted using screws or bolts rather than rivets. Printed-board
32、 mounted connectors shall be mounted in accordance with the manu- facturers instructions. Cables shall be attached to free connectors in accordance with the manufacturers instructions. 1.3 Number of contacts or contact cavities This DS deals with connectors with 3 to 7 contacts. 1.4 Ratings and char
33、acteristics Rated voltage: 50 V a.c. Voltage proof: 1 000 V r.m.s. Current rating at 70 C: depends on version (see 4.2.3) Insulation resistance: initial: 10 G after damp heat: 500 M Climatic category: 25/070/04 Contact spacing: see drawings 1.5 Normative references The following referenced documents
34、 are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60352 (all parts), Solderless connections IEC 60512 (all parts), Connectors for
35、 electronic equipment Tests and measurements IEC 60512-1-100, Connectors for electronic equipment Tests and measurements Part 1-100: General Applicable publications Page 6 EN 610762103:2004 -67016-2301 4002:CEI 7 IEC 60917-2-2, Modular order for the development of mechanical structures for electroni
36、c equipment practices Part 2: Sectional specification Interface coordination dimensions for the 25 mm equipment practice Section 2: Detail specification Dimensions for subracks, chassis, backplanes, front panels and plus-in units IEC 61076-1, Connectors with assessed quality, for use in d.c., low fr
37、equency analogue and digital high speed data applications Part 1: Generic Specification IEC 61076-2, Connectors for use in d.c., low frequency analogue and digital high speed data applications Part 2: Circular connectors with assessed quality Sectional specification 1.6 Marking Each connector shall
38、carry the following markings: mark of origin (manufacturers name or mark); identification of the contact positions, in accordance with Clause 3; IEC type designation (see 1.7) or manufacturers designation. NOTE If a manufacturers designation is used, a cross-reference list between manufacturers and
39、IEC designations should be included in the catalogue or specification sheet. Page 7 EN 610762103:2004 -67016-2301 4002:CEI 8 1.7 IEC Type designation IEC 61076-2-103 LNLLNL Number of detail specification Connector style Number of contacts or contact cavities Type of contact F M Female Male Performan
40、ce level 1 2 3 Assessment level A G (see 2.2) LNL Type of termination I S X Insulation displacement Solder Other LN Shell finish Contact finish Hard gold Silver B A 34567 LL X B P Bright metal Black metal Black plastics Grounding 1 2 3 Current rating S P Signal contacts Power contacts Latching X O W
41、ith latching device Without latching device Panel mount size (fixed styles only) 1 2 3 4 1.8 Ordering information Products may be ordered using the IEC type designation or the manufacturers designation. Page 8 EN 610762103:2004 -67016-2301 4002:CEI 9 2 Technical information 2.1 Definitions For the p
42、urpose of this part of IEC 61076, the definitions in 2.1 of IEC 61076-2 apply. 2.2 Survey of styles and variants The first style letter designates the general form of the connector. Table 1 Designation of first style letter Connector style First style letter Free, straight A Free, straight, for seve
43、re conditions (IP65) B Free, straight, with enhanced screening C Free, right-angle D Fixed, wire terminations E Fixed, wire terminations, with enhanced screening F Fixed, hybrid mounting, separable a) H Fixed, printed-board terminations K Fixed, printed-board terminations, with enhanced screening L
44、Reserved for generic use b) X a) The insert can be mounted on a printed board, while the shell is mounted to a panel. b) Where it is required to refer to all styles having V or H as the second letter, the designations XV or XH shall be used. The second style reference letter designates the orientati
45、on of mounting to a printed board: Table 2 Designation of second style letter Orientation of mounting Second style letter Axis perpendicular to board surface V Axis parallel to board surface H Not a printed-board mounting style X Page 9 EN 610762103:2004 -67016-2301 4002:CEI 01 2.3 Information on ap
46、plication 2.3.1 Complete connectors (pairs) These connectors, especially 3 and 5 contact versions, are very widely used in the professional audio industry. 2.3.2 Reserved 2.3.3 Reserved 2.3.4 Accessories 2.3.4.1 Coding devices Colour-coding rings and/or coloured cable bushings can be used with most
47、styles of free connector. 2.3.5 Shielding/grounding Some styles offer enhanced screening and a number of grounding options. 2.3.6 Shell finish Some styles are available in either bright metal or black finish. Other finishes are possible. 2.3.7 Basic types of terminations Three basic types of termina
48、tion are standardised: solder bucket for wire termination solder tag for through-hole mounting on printed boards insulation-displacement 2.4 Contact arrangements Five contact arrangements with 3 to 7 contacts are standardized. See 1.7 and 3.3.2. 3 Drawings and dimensions 3.1 General Original dimensions in millimetres. Drawings in first angle projection. The shape of the connectors may deviate from those given in the following drawings as long as the specified dimensions are not influenced. Page 10 EN 610762103:2004 -67016-230