《BS-EN-672-1997.pdf》由会员分享，可在线阅读，更多相关《BS-EN-672-1997.pdf（10页珍藏版）》请在三一文库上搜索。
1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS EN 672 : 1997 The Euro
2、pean Standard EN 672 : 1996 has the status of a British Standard ICS 91.180 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Resilient floor coverings Determination of apparent density of agglomerated cork Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 13 17:26:03 GMT+00:0
3、0 2006, Uncontrolled Copy, (c) BSI BS EN 672 : 1997 This British Standard, having been prepared under the direction of the Sector Board for Materials and Chemicals, was published under the authority of the Standards Board and comes into effect on 15 June 1997 BSI 1997 The following BSI references re
4、late to the work on this standard: Committee reference PRI/60 Draft for comment 92/38645 DC ISBN 0 580 27332 6 Amendments issued since publication Amd. No.DateText affected Committees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee
5、PRI/60, Resilient floor coverings, upon which the following bodies were represented: British Adhesives and Sealants Association British Railways Board British Resilient Flooring Manufacturers Association British Rubber Manufacturers Association Ltd. Consumer Policy Committee of BSI Contract Flooring
6、 Association Cork Industry Federation Department of the Environment (British Board of Agre ment) Department of the Environment (Building Research Establishment) Institute of Chartered Arbitrators Royal Institute of British Architects Wood Panel Industries Federation Licensed Copy: sheffieldun sheffi
7、eldun, na, Mon Nov 13 17:26:03 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 672 : 1997 BSI 1997i Contents Page Committees responsibleInside front cover National forewordii Foreword2 Method 1Scope3 2Normative references3 3Principle3 4Apparatus3 5Sampling and preparation of test pieces3 6Condition
8、ing3 7Procedure3 8Calculation and expression of results3 9Test report3 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 13 17:26:03 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ii BSI 1997 BS EN 672 : 1997 National foreword This British Standard has been prepared by Technical Committee PRI/60 and i
9、s the English language version of EN 672 : 1996 Resilient floor coverings Determination of apparent density of agglomerated cork, published by the European Committee for Standardization (CEN). EN 672 : 1996 was produced as a result of international discussion in which the United Kingdom took an acti
10、ve part. Cross-references Publication referred toCorresponding British Standard EN 427 : 1994BS EN 427 : 1994 Resilient floor coverings Determination of side length, squareness and straightness of tiles EN 428 : 1992BS EN 428 : 1993 Resilient floor coverings Determination of overall thickness Compli
11、ance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, the EN title page, pages 2 to 4, an inside back cover and a back cover. Licensed Copy: sheffieldun sheffieldun, na, M
12、on Nov 13 17:26:03 GMT+00:00 2006, Uncontrolled Copy, (c) BSI CEN European Committee for Standardization Comite Europe en de Normalisation Europa isches Komitee fu r Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1996 Copyright reserved to CEN members Ref. No. EN 672 : 1996 E EUROP
13、EAN STANDARDEN 672 NORME EUROPE ENNE EUROPA ISCHE NORM December 1996 ICS 91.180 Descriptors: floor coverings, cork, tests, determination, density (mass volume) English version Resilient floor coverings Determination of apparent density of agglomerated cork Reve tements de sol re silients De terminat
14、ion de la masse volumique dagglome re de lie ge Elastische Bodenbela ge Bestimmung der Rohdichte von Prekork This European Standard was approved by CEN on 1996-11-30. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Sta
15、ndard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French
16、, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, Fra
17、nce, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 13 17:26:03 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Page 2 EN 672 : 1996 BSI 1997 Foreword This European
18、 Standard has been prepared by Technical Committee CEN/TC 134, Resilient and textile floor coverings, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June
19、1997, and conflicting national standards shall be withdrawn at the latest by June 1997. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, German
20、y, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 13 17:26:03 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Page 3 EN 672 : 1996 BSI 1997 1 Scope This European Standard de
21、scribes a method for determining the apparent density of agglomerated cork. The method is based on ISO 3810 : 1987. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate pl
22、aces in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication ref
23、erred to applies. EN 427 Resilient floor coverings Determination of side length, squareness and straightness of tiles EN 428 Resilient floor coverings Determination of overall thickness 3 Principle A test piece of known dimensions is weighed and its apparent density calculated from the quotient of m
24、ass and volume. 4 Apparatus 4.1 The apparatus described in EN 427 for measuring side length and width of tiles. 4.2 The apparatus described in EN 428 for measuring thickness of tiles. 4.3 Balance, with an error limit of 0,5 g. 5 Sampling and preparation of test pieces Take a representative sample fr
25、om the available material, and from that take at least five tiles as test pieces. When the sample comprises a pack of tiles, ensure that the first and the last tiles are not used as test pieces. 6 Conditioning Condition the test pieces at a temperature of (232) C and relative humidity of (505) % for
26、 a minimum of 24 h. Maintain these conditions when carrying out the test. 7 Procedure Determine the dimensions of each test piece, using the apparatus described in 4.1 and 4.2. Record the dimensions in millimetres to the nearest 0,1 mm. Determine the mass of each test piece in grams, using the balan
27、ce (see 4.3), and round off to the nearest gram. 8 Calculation and expression of results From the recorded dimensions, calculate the volume of each test piece and then calculate the apparent density r, using the following expression: r = 1063 M V where Mis the mass of each test piece in grams, round
28、ed off to the nearest gram; Vis the volume of each test piece in cubic millimetres. Calculate the apparent density result as the mean value of the five determinations, and express the result in kilograms per cubic metre, rounded off to the nearest kilogram per cubic metre. 9 Test report The test rep
29、ort shall contain the following information: a) a reference to this standard, i.e. EN 672; b) a complete identification of the product tested, including type, source, manufacturers reference number; c) previous history of the sample; d) the mean value for the apparent density; e) any deviation from
30、this standard which may have affected the results. Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 13 17:26:03 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 4blank Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 13 17:26:03 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BSI 1997 BS EN 672 : 1997 Li
31、st of references See national foreword. Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 13 17:26:03 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
32、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Eu
33、rope and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our pro
34、ducts and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers
35、members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996
36、7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international sta
37、ndards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up t
38、o date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyrig
39、ht, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise
40、 without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written pe
41、rmission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070. Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 13 17:26:03 GMT+00:00 2006, Uncontrolled Copy, (c) BSI