《BS-EN-949-1999.pdf》由会员分享，可在线阅读，更多相关《BS-EN-949-1999.pdf（8页珍藏版）》请在三一文库上搜索。
1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS EN 949:1999 The Europe
2、an Standard EN 949:1998 has the status of a British Standard ICS 91.060.50 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Windows and curtain walling, doors, blinds and shutters Determination of the resistance to soft and heavy body impact for doors Licensed Copy: sheffieldun
3、 sheffieldun, na, Tue Nov 07 06:32:54 GMT+00:00 2006, Uncontrolled Copy, (c) BSI This British Standard, having been prepared under the direction of the Sector Committee for Building and Civil Engineering, was published under the authority of the Standards Committee and comes into effect on 15 May 19
4、99 BSI 05-1999 ISBN 0 580 32280 7 BS EN 949:1999 Amendments issued since publication Amd. No.DateText affected National foreword This British Standard is the English language version of EN 949:1998. The UK participation in its preparation was entrusted to Technical Committee B/538, Doors, windows, s
5、hutters, hardware and curtain walling, which has the responsibility to: aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European dev
6、elopments and promulgate them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. This British Standard forms part of a package of standards on doors which will not become fully effective until all standards in the package have been published
7、 and any superseded standards have been withdrawn. The date of withdrawal for national standards will be agreed within CEN and will be notified. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standard
8、s Catalogue under the section entitled International Standards Correspondence Index, or by using the Find facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for thei
9、r correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 4, an inside back cover and a back cover. Licensed Copy: sheffieldun sheff
10、ieldun, na, Tue Nov 07 06:32:54 GMT+00:00 2006, Uncontrolled Copy, (c) BSI CEN European Committee for Standardization Comite Europe en de Normalisation Europa isches Komitee fu r Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1998 CEN All rights of exploitation in any form and by a
11、ny means reserved worldwide for CEN national Members. Ref. No. EN 949:1998 E EUROPEAN STANDARDEN 949 NORME EUROPE ENNE EUROPA ISCHE NORM December 1998 ICS 91.060.50Supersedes EN 162:1985 Descriptors: windows, doors, blinds, closures, tests, mechanical strength, shock resistance English version Windo
12、ws and curtain walling, doors, blinds and shutters Determination of the resistance to soft and heavy body impact for doors Fene tres et fac ades-rideaux, portes, stores et fermetures De termination de la re sistance au choc de corps mou et lourd pour les portes Fenster, Tu ren, Dreh- und Rolla den,
13、Vorhangfassaden Ermittlung der Widerstandsfa higkeit von Tu ren gegen Aufprall eines weichen und schweren Stoko rpers This European Standard was approved by CEN on 26 November 1998. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving th
14、is European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (
15、English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech
16、Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. Licensed Copy: sheffieldun sheffieldun, na, Tue Nov 07 06:32:54 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Page 2 EN 949:1998 BSI 05
17、-1999 Foreword This European Standard has been prepared by Technical Committee CEN/TC 33, Doors, windows, shutters and building hardware, the Secretariat of which is held by AFNOR. This European Standard replaces EN 162:1985. This European Standard shall be given the status of a national standard, e
18、ither by publication of an identical text or by endorsement, at the latest by June 1999, and conflicting national standards shall be withdrawn at the latest by December 1999. This standard is one of a series of standards for doors. The test method relates to performance requirements to be published
19、in EN 1192, Doors Mechanical strength Requirements and classification. This standard has been prepared taking into account ISO 8270 and EN 162. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Stan
20、dard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Licensed Copy: sheffieldun sheffieldun, na, Tue Nov 07 06:32:54 GMT+00:00 2006, Uncontrolled Copy,
21、 (c) BSI Page 3 EN 949:1998 BSI 05-1999 Introduction For manufacturers of door leaves whose products are not sold as part of a known doorset, or where such door leaves can be used in a sliding door assembly, provision is made for claiming compliance with the relevant requirements by the testing of s
22、uch door leaves in a typical frame. Nevertheless, the fact that a particular door leaf meets with the relevant requirements in this way does not necessarily mean that a door assembly incorporating that door leaf will meet the requirements. 1 Scope This European standard applies to all doors. The sta
23、ndard specifies the method to be used to determine the damage caused by striking with a soft and heavy body, the face of a closed door leaf fixed in its own door frame as part of a doorset. NOTESuch forces that might reasonably be expected from impacts by human bodies and substantial objects with si
24、milar characteristics should neither damage, nor impair the normal performance of, a door. The method may also be used in respect of a door leaf submitted for test in a frame which the manufacturer considers appropriate to and typical for the intended utilization. 2 Apparatus 2.1 Test surround, a su
25、rround in which the specimen is tested, which shall be sufficiently rigid to withstand the test load without deflecting to an extent likely to influence the test result. 2.2 Impact equipment, impact body of total mass (300,6 )kg, consisting of a spherical leather bag of diameter approximately 350 mm
26、, containing dry sand of apparent density approximately 1500 kg/m3which passes through a sieve of 2 mm mesh. Wires, pulleys, release hook and suitable heightregulating devices. 2.3 Measuring equipment, a dial or digital gauge accurate to 0,01 mm, mounted at the centre of a reference bar capable of s
27、panning the width of the door leaf. 3 Test specimens Test specimens shall be stored and tested in a nondestructive environment within the ranges of 15 8C to 30 8C and 25 % to 75 % relative humidity. Doors which are designed to be glazed, shall be supplied for testing with all glazing carried out in
28、accordance with the door manufacturers specification. 4 Procedure The door leaf to be tested shall be closed and where applicable secured in accordance with its normal operating mode. NOTE 1In its normal operating mode a door leaf can be unsecured, or secured by latch, lock, bolt or other means. Ide
29、ntify the impact point. This shall occur at the centre of the door leaf. Where the impact point coincides with the handle, this shall be removed. With the reference bar, measure any deviation in flatness across the width of the door leaf at the height of the impact point, to the nearest 0,1 mm. Susp
30、end the impact body as shown in Figure 1 so that at rest it makes light contact with the surface of the door leaf and so that its centre of gravity is positioned on a line perpendicular to the door leaf at its centre. Raise the impact body so that the drop height h, with a tolerance of10 mm, corresp
31、onds to the required impact energy. Release the impact body such that it strikes the door leaf at the impact point. NOTE 2Repetition of this operation will necessitate re-shaping of the impact body. Repeat the measurement of deviation in flatness across the width of the door leaf at the height of th
32、e impact point, to the nearest 0,1 mm. 5 Expression of results Record: the residual deformation in flatness, across the width at the height of the impact point. 6 Test report The test report shall contain the following information: a) reference to this European Standard; b) all necessary details to
33、identify the doorset or door leaf; c) all relevant details concerning the type, specified dimensions, materials, form and construction of the doorset or door leaf, including the position of hardware; d) full details of the frame and hardware supplied if the assembly is not a doorset; e) the position
34、 and size of any glazed or panelled areas; f) laboratory storage and testing conditions; g) the face or faces tested and number of impacts applied to each face; h) the impact energy in joules; i) the results expressed as in clause 5; j) details of any damage that appeared during the test; k) name of
35、 testing laboratory; l) date of test. Licensed Copy: sheffieldun sheffieldun, na, Tue Nov 07 06:32:54 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Page 4 EN 949:1998 BSI 05-1999 1pulley; 2wire; 3drop height, h10 mm; 4release hook; 5regulating device; 6impact body; 7doorset; 8test rig. Figure 1 Apparat
36、us for soft and heavy body impact test and test principle Licensed Copy: sheffieldun sheffieldun, na, Tue Nov 07 06:32:54 GMT+00:00 2006, Uncontrolled Copy, (c) BSI blank Licensed Copy: sheffieldun sheffieldun, na, Tue Nov 07 06:32:54 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BSI 389 Chiswick High
37、Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Insti
38、tution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards sh
39、ould make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical commi
40、ttee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all
41、 BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless
42、 otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its prod
43、ucts and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Admin
44、istration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be r
45、eproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and si
46、ze, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070. Licensed Copy: sheffieldun sheffieldun, na, Tue Nov 07 06:32:54 GMT+00:00 2006, Uncontrolled Copy, (c) BSI