《BS-MA-105-1-1987 ISO-6765-1985.pdf》由会员分享，可在线阅读，更多相关《BS-MA-105-1-1987 ISO-6765-1985.pdf（8页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD MARINE SERIES CONFIRMED JULY 1999 BS MA 105-1: 1987 ISO 6765:1985 Series 3 shipborne barges Part 1: Specification for main dimensions ISO title: Shipbuilding Shipborne barges, series 3 Main dimensions UDC 629.122.3:629.014.3 Licensed Copy: London South Bank University, London South
2、Bank University, Sat Dec 09 02:22:45 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS MA 105-1:1987 This British Standard, having been prepared under the direction of the Shipbuilding and Marine Standards Committee, was published under the authority of the Board of BSI and comes into effect on 31 July
3、1987 BSI 02-2000 The following BSI references relate to the work on this standard: Committee reference SME/14 Draft for comment 83/70707 DC ISBN 0 580 16012 2 Committees responsible for this British Standard The preparation of this British Standard was entrusted by the Shipbuilding and Marine Standa
4、rds Committee (SME/-) to Technical Committee SME/14, upon which the following bodies were represented: Association of Master Lightermen and Barge Owners (Port of London) British Tugowners Association British Waterways Board HM Customs and Excise Shiprepairers and Shipbuilders Independent Association
5、 Amendments issued since publication Amd. No.Date of issueComments Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 02:22:45 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS MA 105-1:1987 BSI 02-2000i Contents Page Committees responsibleInside front cover National f
6、orewordii 1Scope and field of application1 2Definition1 3Barge dimensions1 4Adjusting and securing components1 5Tolerances3 Figure 1 Shipborne barge, series 3 Main dimensions1 Figure 2 Arrangement of the tie-down fittings2 Figure 3 Arrangement of points of contact in a barge and of securing devices
7、in a barge carrier3 Table 1 Main barge dimensions1 Table 2 Interchangeability tolerances3 Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 02:22:45 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS MA 105-1:1987 ii BSI 02-2000 National foreword This Part of BS MA 105
8、 has been prepared under the direction of the Shipbuilding and Marine Standards Committee and is identical with ISO 6765:1985 “Shipbuilding Shipborne barges, series 3 Main dimensions”, published by the International Organization for Standardization (ISO). ISO 6765 was produced as a result of interna
9、tional discussion in which the UK took an active part. Terminology and conventions. The text of the International Standard has been approved as suitable for publication as a British Standard without deviation. Some terminology and certain conventions are not identical with those used in British Stan
10、dards; attention is drawn especially to the following. Where the words “International Standard” appear, referring to this standard, they should be read as “Part of MA 105”. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are respo
11、nsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages 1 to 3 and a back cover. This standard has been updated (see copyri
12、ght date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 02:22:45 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS MA 105-1:1987 BSI 02-20001 1 Scope
13、 and field of application This International Standard lays down the main dimensions and the dimensions of the principal constructional elements of shipborne barges, series 3. 2 Definition shipborne barge, series 3 barge handled aboard a barge carrier by an elevator or by a system based on the floati
14、ng-dock principle 3 Barge dimensions The main dimensions of barges, series 3, shall be in accordance with Table 1. The stationary equipment installed on the deck at fore and aft ends in all places shall nowhere project beyond the overall height. 4 Adjusting and securing components The adjusting and
15、securing components include: a) bottom positioning angles; b) tie-down fittings for securing barges on the upper deck of a barge carrier; c) points of contact of securing devices (jacks) on the tween deck of a carrier. The arrangements are given in Figure 1, Figure 2 and Figure 3. Table 1 Main barge
16、 dimensions Main dimensions Distance between the outboard edge of the positioning angle and longitudinal centreline plane Maximum draught in fresh water Maximum displacement LengthWidth Height Depth at ends Mid-depth overall (without positioning angles) LBHH1NTmaxD mmmmmmmmmmmmtonnes 38 25011 0003 9
17、005 3003 4073 4601 300 NOTE 1The form of the hull shapes is presented schematically and is not specified by this International Standard. NOTE 2The length of the positioning angle should be not less than 80 % of the bottom length of a shipborne barge. NOTE 3The diameter of the positioning bitt is 150
18、 mm. Figure 1 Shipborne barge, series 3 Main dimensions Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 02:22:45 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS MA 105-1:1987 2 BSI 02-2000 Figure 2 Arrangement of the tie-down fittings Licensed Copy: London South B
19、ank University, London South Bank University, Sat Dec 09 02:22:45 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS MA 105-1:1987 BSI 02-20003 5 Tolerances Table 2 specifies the tolerances for those dimensions which determine the interchangeability of the barges with respect to their handling aboard a b
20、arge carrier. Table 2 Interchangeability tolerances NOTEDimensions for which tolerances are not specified in this International Standard may be toleranced in accordance with national shipbuilding standards. Figure 3 Arrangement of points of contact in a barge and of securing devices in a barge carri
21、er Values in millimetres Tolerance on: LBHN 38 22 15 +0 5 Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 02:22:45 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS MA 105-1: 1987 ISO 6765:1985 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Instituti
22、on BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should
23、 make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee
24、 responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI
25、, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless oth
26、erwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products
27、 and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administr
28、ation. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be repro
29、duced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size,
30、type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070. Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 02:22:45 GMT+00:00 2006, Uncontrolled Copy, (c) BSI