《BS-ISO-13774-1998.pdf》由会员分享，可在线阅读，更多相关《BS-ISO-13774-1998.pdf（12页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS ISO 13774:1998 Rubber and plastics hoses for fuels for internal combustion engines Method of test for flammability ICS 13.220.40; 23.040.70 Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 03:58:42 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS ISO 13774:1998 This British St
2、andard, having been prepared under the direction of the Sector Committee for Materials and Chemicals, was published under the authority of the Standards Committee and comes into effect on 15 October 1999 BSI 04-2000 ISBN 0 580 35326 5 National foreword This British Standard reproduces verbatim ISO 1
3、3774:1998 and implements it as the UK national standard. The UK participation in its preparation was entrusted by Technical Committee PRI/66, Rubber and plastics tubing, hoses and hose assemblies, to Subcommittee PRI/66/4, Methods of test, which has the responsibility to: aid enquirers to understand
4、 the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this
5、committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or
6、by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer im
7、munity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, the ISO title page, pages ii to iv, pages 1 to 3 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be
8、indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No.DateComments Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 03:58:42 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS ISO 13774:1998 BSI 04-2000i Contents Page National forewordInside front c
9、over Forewordiii Text of ISO 137741 Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 03:58:42 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ii blank Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 03:58:42 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Licensed Copy: sheffieldun sheffieldun, n
10、a, Sun Nov 26 03:58:42 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS ISO 13774:1998 ii BSI 04-2000 Contents Page Forewordiii 1Scope1 2Normative reference1 3Principle1 4Apparatus and materials1 5Test pieces1 6Conditioning of test pieces1 7Procedure1 8Test report3 Figure 1 Test apparatus2 Descriptors:
11、 Rubber products, plastics products, hoses, fluid circuits, automotive fuels, rubber hoses, plastics hoses, tests, flammability testing. Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 03:58:42 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS ISO 13774:1998 BSI 04-2000iii Foreword ISO (the Inter
12、national Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has
13、been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical st
14、andardization. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. International Standard ISO 13774 was prepared by Technical
15、 Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 1, Hoses (rubber and plastics). Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 03:58:42 GMT+00:00 2006, Uncontrolled Copy, (c) BSI iv blank Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 03:58:42 GMT+00:00 2006, Uncont
16、rolled Copy, (c) BSI BS ISO 13774:1998 BSI 04-20001 WARNING Persons using this International Standard should be familiar with normal laboratory practice. This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user to est
17、ablish appropriate safety and health practices and to ensure compliance with any national regulatory conditions. Attention is drawn to the need for ensuring that the test specified in this International Standard is carried out under suitable environmental conditions and that personnel are adequately
18、 protected against risk of fire and inhalation of smoke and/or toxic products of combustion. 1 Scope This International Standard specifies a method for assessing the flammability of hoses with a nominal bore of 16 or smaller, intended for use with petroleum fuels for internal-combustion engines. NOT
19、EThe method of test for flammability of other types of rubber and plastics hoses is given in ISO 8030:1995, Rubber and plastics hoses Method of test for flammability. 2 Normative reference The following standard contains provisions which, through reference in this text, constitute provisions of this
20、 International Standard. At the time of publication, the edition indicated was valid. All standards are subject to revision, and parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent edition of the standard indicated belo
21、w. Members of IEC and ISO maintain registers of currently valid International Standards. ISO 471:1995, Rubber Temperatures, humidities and times for conditioning and testing. 3 Principle The hose, filled with heptane, is subjected to fire. No leakage may occur earlier than T min after ignition of th
22、e fuel in the tray. The time T is specified in the appropriate product standard. 4 Apparatus and materials 4.1 Draught-free room, maintained at a standard temperature (see ISO 471). 4.2 Steel stands, for supporting the test piece in a horizontal position above the fuel tray (see Figure 1). 4.3 Glass
23、 tube, for supplying the test piece with fuel at a certain pressure (fuel level 900 mm above the test piece). 4.4 Fuel tray, of square shape, 350 mm 350 mm, with vertical, 40-mm-high sides. 4.5 Fuel, consisting of commercial heptane with a distillation range of 80 C to 110 C. 5 Test pieces Hose asse
24、mblies with a length of 400 mm (see Figure 1) shall be used. At least three test pieces shall be tested. 6 Conditioning of test pieces No test shall be carried out within 24 h of manufacture. Test pieces shall be conditioned at standard temperature and humidity (see ISO 471) for at least 3 h before
25、testing. This may be part of the 24 h period after manufacture. 7 Procedure WARNING Large flames and burning waste fluid could occur during any leakage. Therefore the test shall be performed in a non-combustible environment by personnel equipped with protective equipment and fire-fighting equipment.
26、 7.1 Preparations Arrange the test equipment to conform to Figure 1 without mounting any test piece. Fill the fuel tray as stated below, ignite the fuel and note that a stable flame is obtained. Non-measurable draught effects in the room could influence the flame and, if so, the position of the fuel
27、 tray shall be changed, in order to embrace the hose and one of its ends in the flame. Extinguish the flames and allow the whole apparatus to cool to ambient temperature. 7.2 Test Mount a test piece in place and fill it with fuel by opening the fuel valve. Ensure that no air is left in the hose. Adj
28、ust the fuel level to 900 mm above the test piece. Pour 0,5 dm3 of water and 2 dm3 of heptane into the fuel tray and ignite the heptane. The fuel tray shall be placed so that two of the sides are parallel with the test piece. Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 03:58:42 GMT+00:00
29、2006, Uncontrolled Copy, (c) BSI BS ISO 13774:1998 2 BSI 04-2000 Allow the heptane to burn and record the time to leakage. Leakage will be evident by the increase in the intensity of the fire at the position of leakage. The test is terminated when leakage occurs or when the heptane in the fuel tray
30、is burnt off. If the flame is very unstable during the test and does not expose the test piece to a full extent during more than 25 % of the duration of the test, or if the time to leakage in any test deviates by more than 30 s from the mean value determined, test another two test pieces. After each
31、 test, cool the fuel lines and fuel tray to ambient temperature before mounting a new test piece and replacing the water and fuel. Figure 1 Test apparatus Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 03:58:42 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS ISO 13774:1998 BSI 04-20003 8 Test
32、report The test report shall include the following particulars: a) a reference to this International Standard; b) a full description of the hose tested; c) the test conditions, e.g. the temperature in the room and observations concerning any draught; d) the time to leakage for each test piece and th
33、e mean value; e) if no leakage occurs, the time the hose was exposed to fire; f) the date of the test. Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 03:58:42 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS ISO 13774:1998 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Instituti
34、on BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should
35、 make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee
36、 responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI
37、, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless oth
38、erwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products
39、 and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administr
40、ation. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be repro
41、duced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size,
42、type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070. Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 03:58:42 GMT+00:00 2006, Uncontrolled Copy, (c) BSI