《BS-EN-ISO-14530-1-2000.pdf》由会员分享，可在线阅读，更多相关《BS-EN-ISO-14530-1-2000.pdf（16页珍藏版）》请在三一文库上搜索。
1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS EN ISO 14530-1:2000 Th
2、e European Standard EN ISO 14530-1:1999 has the status of a British Standard ICS 83.080.10 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Plastics Unsaturated-polyester powder moulding compounds (UP-PMCs) Part 1: Designation system and basis for specifications Licensed Copy:
3、sheffieldun sheffieldun, na, Mon Nov 20 02:24:33 GMT+00:00 2006, Uncontrolled Copy, (c) BSI This British Standard, having been prepared under the direction of the Sector Committee for Materials and Chemicals, was published under the authority of the Standards Committee and comes into effect on 15 Ja
4、nuary 2000 BSI 01-2000 ISBN 0 580 35885 2 BS EN ISO 14530-1:2000 Amendments issued since publication Amd. No.DateComments National foreword This British Standard is the English language version of EN ISO 14530-1:1999. It is identical with ISO 14530-1:1999. The UK participation in its preparation was
5、 entrusted to Technical Committee PRI/42, Fibre reinforced thermosetting plastics and prepregs, which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep th
6、e UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references Attention is drawn to the fact that CEN and CENELEC Standards normally i
7、nclude an annex which lists normative references to international publications with their corresponding European publications. The British Standards which implement these international or European publications may be found in the BSI Standards Catalogue under the section entitled International Stand
8、ards Correspondence Index, or by using the Find facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard
9、does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN ISO title page, the EN ISO foreword page, the ISO title page, pages ii and iii, a blank page, pages 1 to 6, an inside back cover and a back cover. The BSI
10、copyright notice displayed in this document indicates when the document was last issued. Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 02:24:33 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 02:24:33 GMT+00:00 2006, Uncontrolled Copy, (c) B
11、SI EN ISO 14530-1:1999 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 02:24:33 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ? Reference number ISO 14530-1:1999(E) INTERNATIONAL STANDARD ISO 14530-1 First edition 1999-11-15 Plastics Unsaturated-polyester powder moulding compounds (UP-PMCs) Part
12、 1: Designation system and basis for specifications Plastiques Poudres mouler base de polyester non satur (UP-PMC) Partie 1: Systme de dsignation et base de spcification EN ISO 14530-1:1999 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 02:24:33 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ii?
13、 EN ISO 14530-1:1999 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 02:24:33 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO -035411:(9991E) ?iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The w
14、ork of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-govern
15、mental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. Dra
16、ft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this part
17、 of ISO 14530 may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. International Standard ISO 14530-1 was prepared by Technical Committee ISO/TC 61,Plastics, Subcommittee SC 12,Thermosetting materials. ISO 14530 consists of the followi
18、ng parts, under the general titlePlastics Unsaturated-polyester powder moulding compounds (UP-PMCs): ?Part 1: Designation system and basis for specifications ?Part 2: Preparation of test specimens and determination of properties ?Part 3: Requirements for selected moulding compounds EN ISO 14530-1:19
19、99 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 02:24:33 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN ISO 14530-1:1999 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 02:24:33 GMT+00:00 2006, Uncontrolled Copy, (c) BSI INTERNATIONAL STANDARDISO 14530-1:1999(E) ISO 9991 All irhgts s
20、eredevr1 Plastics Unsaturated-polyester powder moulding compounds (UP-PMCs) Part 1: Designation system and basis for specifications 1Scope 1.1This part of ISO 14530 establishes a data block system for the designation of unsaturated-polyester powder moulding compounds (UP-PMCs). 1.2The various types
21、of UP-PMC are differentiated from each other by a classification system based on information about the filler/reinforcement type and content, the intended method of processing, any special properties and those of the special properties used specifically for designation purposes (designatory properti
22、es). 1.3This part of ISO 14530 is applicable to all UP-PMCs ready for normal use in the form of powder, granules or ground material. 1.4It is not intended to imply that materials having the same designation necessarily give the same performance. This part of ISO 14530 does not provide engineering da
23、ta, performance data or data on processing conditions which may be required to specify a material for a particular application and/or method of processing. If such additional properties are required, they shall be determined in accordance with the test methods specified in ISO 14530-2, if suitable.
24、1.5Whenever general requirement data, as covered by ISO 14530-3, need to be indicated, this is also done using this data block system. 1.6To ensure that code-letters and code-numbers remain unambiguous, and to avoid conflicts within the system, any new code-letters or code-numbers for use in data bl
25、ock 1, 2 or 3 shall be approved before use by the secretariats of ISO/TC 61/SC 1, SC 12 and SC 13. 2Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of this part of ISO 14530. For dated references, subsequent amend
26、ments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this part of ISO 14530 are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition
27、of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards. ISO 75-2:1993,Plastics Determination of temperature of deflection under load Part 2: Plastics and ebonite. ISO 179-1:1),Plastics Determination of Charpy impact propert
28、ies Part 1: Non-instrumented impact test. 1)To be published. (Revision of ISO 179:1993) EN ISO 14530-1:1999 1 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 02:24:33 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO -035411:(9991E) 2 ISO 9991 All irhgts seredevr ISO 472:1999,Plastics Vocabulary
29、. ISO 1043-1:1997,Plastics Symbols and abbreviated terms Part 1: Basic polymers and their special characteristics. ISO 1043-2:2),Plastics Symbols and abbreviated terms Part 2: Fillers and reinforcing materials. ISO 14530-2:1999,Plastics Unsaturated-polyester powder moulding compounds (UP-PMCs) Part
30、2: Preparation of test specimens and determination of properties. ISO 14530-3:1999,Plastics Unsaturated-polyester powder moulding compounds (UP-PMCs) Part 3: Requirements for selected moulding compounds. 3Terms and definitions For the purposes of this part of ISO 14530, the terms and definitions giv
31、en in ISO 472 and ISO 14530-2 apply, plus the following: 3.1 powder moulding compound powder, granules or ground material capable of flowing freely through the feed systems of processing machines, as well as moulding compounds in the form of flakes which are normally not thought of as powders The ab
32、breviation for powder moulding compound is PMC by analogy with bulk moulding compound (BMC) and sheet moulding compound (SMC). 3.2 UP-PMC abbreviation for powder moulding compounds based on unsaturated-polyester resins for both injection and compression moulding 4Designation system 4.1General The de
33、signation system defined in this part of ISO 14530 is based on the following standardized pattern: Designation Identity block DescriptionISO Individual-item block blockStandard Data block 1 Data block 2 Data block 3 Data block 4 Data block 5 The designation consists of an optional description block,
34、 reading “PMC“, and an identity block comprising the International Standard number and an individual-item block. For unambiguous designation, the individual-item block is subdivided into five data blocks comprising the following information: 2)To be published. (Revision of ISO 1043-2:1988) EN ISO 14
35、530-1:1999 2 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 02:24:33 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO -035411:(9991E) ISO 9991 All irhgts seredevr3 Data block 1: Marking block Item 1: Identification of the basic polymer by its symbol, in accordance with ISO 1043-1; Item 2: Natu
36、re of the designatory reinforcement materials or fillers, in accordance with ISO 1043-2; Item 3: Form of the designatory reinforcement materials or fillers, in accordance with ISO 1043-2; Item 4: Nominal content of the designatory reinforcement materials or fillers, in accordance with Table 1. Data
37、block 2: Method of processing Method of processing for which the moulding compound is intended, designated in accordance with Table 2. Data block 3: Properties Item 1: Special properties, in accordance with Table 3; Item 2: Designatory property No. 1 impact strength determined in accordance with ISO
38、 179-1; Item 3: Designatory property No. 2 temperature resistance determined in accordance with ISO 75-2. Data block 4: Further information, taken from an international, national or company standard. Data block 5 (optional): Additional requirements The first character of the individual-item block sh
39、all be a hyphen. The data blocks shall be separated from each other by commas. If a data block is not used, this shall be indicated by an “X“ (= not applicable), but only if another block follows. For labelling purposes, and provided no other blocks follow, the comma between blocks 1 and 2 can be om
40、itted. There is no need to fill in data blocks if they are not required. 4.2Data block 1 Item 1: After the hyphen, unsaturated-polyester powder moulding compounds shall be identified by the symbol UP, in accordance with ISO 1043-1. Mixtures and modifications shall be designated in accordance with IS
41、O 1043-1:1997, subclauses 4 and 5. The following information shall be restricted to designatory fillers/reinforcements used in the material in question: Item 2: Nature of filler/reinforcement, in accordance with Table 1. Item 3: Form of filler/reinforcement, in accordance with Table 1. Item 4: Nomin
42、al content (mass %) of filler/reinforcement, in accordance with Table 1. Note, in particular, the following: ?the same code-letters have different meanings when used for item 2 and item 3; ?whenever information needs to be indicated only for item 3, an “X“ ( = not applicable) is required for item 2.
43、 EN ISO 14530-1:1999 3 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 02:24:33 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO -035411:(9991E) 4 ISO 9991 All irhgts seredevr 4.3Data block 2 In this data block, information about the method of processing is given using the code-letters specifie
44、d in Table 2. The code-letter used to indicate the intended method of processing in data block 2 shall be selected carefully. Certain brands of material can be processed in more than one way, e.g. either by compression moulding (Q) or by injection moulding (M). Such brands shall be designated “gener
45、al purpose“ (G). The designation of special methods of processing shall be reserved for specially modified materials. Table 1 Code-letters and code-numbers used in data block 1 Nature of filler/reinforcement (in accordance with ISO 1043-2) Form of filler/reinforcement (in accordance with ISO 1043-2)
46、 Percentage content by mass, w % (m/m) C D E G K L1 L2 M P Q R S T W X Z Carbon Aluminium oxide trihydrate Clay Glass Calcium carbonate Cellulose Cotton Mineral Mica Silica Recycled material Synthetic organic Talc Wood Not specified Others B C D F G S X Z Balls; beads; spheres Chips; cuttings Fines;
47、 powder Fibre Ground Scale; flakes Not specified Others 05 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 w 7,5 7,5 u w 12,5 12,5 u w 17,5 17,5 u w 22,5 22,5 u w 27,5 27,5 u w 32,5 32,5 u w 37,5 37,5 u w 42,5 42,5 u w 47,5 47,5 u w 52,5 52,5 u w 57,5 57,5 u w 62,5 62,5 u w 67,5 67,5 u w 72,5
48、72,5 u w 77,5 77,5 u w 82,5 82,5 u w 87,5 87,5 u w 92,5 92,5 u w 97,5 NOTEMixtures of materials and/or forms may be indicated by combining the relevant codes using the sign “+“ and placing the whole between parentheses. For example, a mixture of 20 % glass fibre (GF) and 20 % mineral dust (MD) would
49、 be indicated by (GF20+MD20). Table 2 Code-letters used in data block 2 for the method of processing GGeneral purposeTTransfer moulding MInjection mouldingXNot specified QCompression mouldingZOthers EN ISO 14530-1:1999 4 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 02:24:33 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO -035411:(9991E) ISO 9991 All irhgts seredevr5 4.4Data block 3 4.4.1General In this data block, the special properties (see 4.4.2) are