《BS-EN-ISO-1043-4-1999.pdf》由会员分享，可在线阅读，更多相关《BS-EN-ISO-1043-4-1999.pdf（16页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS EN ISO 1043-4:1999 Plastics Symbols and abbreviated terms Part 4: Flame retardants The European Standard EN ISO 1043-4:1999 has the status of a British Standard ICS 01.040.83; 83.040.30 Licensed Copy: sheffieldun sheffieldun, na, Wed Nov 15 05:38:45 GMT+00:00 2006, Uncontrolled C
2、opy, (c) BSI BS EN ISO 1043-4:1999 This British Standard, having been prepared under the direction of the Sector Committee for Materials and Chemicals, was published under the authority of the Standards Committee and comes into effect on 15 August 1999 BSI 03-2000 ISBN 0 580 32812 0 National forewor
3、d This British Standard is the English language version of EN ISO 1043-4:1999. It is identical with ISO 1043-4:1998. The UK participation in its preparation was entrusted to Technical Committee PRI/10, Terminology for rubbers and plastics, which has the responsibility to: aid enquirers to understand
4、 the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this
5、committee can be obtained on request to its secretary. Cross-references Attention is drawn to the fact that CEN and CENELEC Standards normally include an annex which lists normative references to international publications with their corresponding European publications. The British Standards which i
6、mplement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not p
7、urport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside fron
8、t cover, pages i and ii, the EN ISO title page, page 2, the ISO title page, pages ii to iv, pages 1 to 4 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments
9、 issued since publication Amd. No.DateComments Licensed Copy: sheffieldun sheffieldun, na, Wed Nov 15 05:38:45 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN ISO 1043-4:1999 BSI 03-2000i Contents Page National forewordInside front cover Foreword2 Forewordiii Text of ISO 1043-41 Licensed Copy: shef
10、fieldun sheffieldun, na, Wed Nov 15 05:38:45 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ii blank Licensed Copy: sheffieldun sheffieldun, na, Wed Nov 15 05:38:45 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 1043-4 May 1999 ICS 83.040.30; 83.080.0
11、1 English version Plastics Symbols and abbreviated terms Part 4: Flame retardants (ISO 1043-4:1998) Plastiques Symboles et abrviations Partie 4: Ignifuges (ISO 1043-4:1998) Kunststoffe Kennbuchstaben und Kurzzeichen Teil 4: Flammschutzmittel (ISO 1043-4:1998) This European Standard was approved by C
12、EN on 18 April 1999. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards
13、 may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the
14、Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Ki
15、ngdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1999 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 1043-
16、4:1999 E Licensed Copy: sheffieldun sheffieldun, na, Wed Nov 15 05:38:45 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN ISO 1043-4:1999 BSI 03-2000 2 Foreword The text of the International Standard from Technical Committee ISO/TC 61 “Plastics” of the International Organization for Standardization (IS
17、O) has been taken over as an European Standard by Technical Committee CEN/TC 249 “Plastics”, the secretariat of which is held by IBN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 1999,
18、 and conflicting national standards shall be withdrawn at the latest by November 1999. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland,
19、 France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of the International Standard ISO 1043-4:1998 has been approved by CEN as a European Standard without any modification. NOTENor
20、mative references to International Standards are listed in Annex ZA (normative). Licensed Copy: sheffieldun sheffieldun, na, Wed Nov 15 05:38:45 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Licensed Copy: sheffieldun sheffieldun, na, Wed Nov 15 05:38:45 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN IS
21、O 1043-4:1999 ii BSI 03-2000 Contents Page Forewordiii 1Scope1 2Normative references1 3Definition1 4Application of symbols1 5Code numbers for flame retardants2 Annex ZA (normative) Normative references to international publications with their relevant European publications4 Descriptors: Plastics, fl
22、ame proofing, retardants, symbols, abbreviations, designation, numeric codes. Licensed Copy: sheffieldun sheffieldun, na, Wed Nov 15 05:38:45 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN ISO 1043-4:1999 BSI 03-2000iii Foreword ISO (the International Organization for Standardization) is a worldwide
23、federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that c
24、ommittee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Draft International Standards adopted by th
25、e technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. International Standard ISO 1043-4 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 1, Termin
26、ology. ISO 1043 consists of the following parts, under the general title Plastics Symbols and abbreviated terms: Part 1: Basic polymers and their special characteristics; Part 2: Fillers and reinforcing materials; Part 3: Plasticizers; Part 4: Flame retardants. Licensed Copy: sheffieldun sheffieldun
27、, na, Wed Nov 15 05:38:45 GMT+00:00 2006, Uncontrolled Copy, (c) BSI iv blank Licensed Copy: sheffieldun sheffieldun, na, Wed Nov 15 05:38:45 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN ISO 1043-4:1999 BSI 03-20001 1 Scope This part of ISO 1043 provides uniform symbols for flame retardants added t
28、o plastics materials. The symbols are written with the abbreviated term “FR” and one or more succeeding code numbers as given in clause 5. They are used in addition to the symbols for the plastics materials, for plastics material designation and for identification and marking of plastics products. 2
29、 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this part of ISO 1043. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this part o
30、f ISO 1043 are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO maintain registers of currently valid International Standards. ISO 1043-1:1997, Plastics Symbols and abbreviated terms Part 1: Basic polymers and the
31、ir special characteristics. ISO 1043-2:1988, Plastics Symbols Part 2: Fillers and reinforcing materials. ISO 1043-3:1996, Plastics Symbols and abbreviated terms Part 3: Plasticizers. 3 Definition For the purposes of this part of ISO 1043, the following definition applies: 3.1 flame retardant a subst
32、ance that markedly retards the propagation of a flame NOTEIncluded are flame retardants that are incorporated in prepolymers. 4 Application of symbols The symbols are written with the abbreviated term “FR”, in capital letters, followed, without a space, by a two-digit code number enclosed in parenth
33、eses and selected, as appropriate, from the list given in clause 5. Only flame retardants exceeding 1 % (m/m) have to be identified. These symbols are used in addition to the symbols for a plastics material derived from parts 1, 2 and 3 of ISO 1043. EXAMPLE 1: EXAMPLE 2: Licensed Copy: sheffieldun s
34、heffieldun, na, Wed Nov 15 05:38:45 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN ISO 1043-4:1999 2 BSI 03-2000 5 Code numbers for flame retardants The code numbers are grouped according to the chemical composition of the flame retardant. NOTEAdditional materials will be coded as required and will f
35、orm amendments to this part of ISO 1043. Halogenated compounds: Code 10aliphatic/alicyclic chlorinated compounds 11aliphatic/alicyclic chlorinated compounds in combination with antimony compounds 12aromatic chlorinated compounds 13aromatic chlorinated compounds in combination with antimony compounds
36、 14aliphatic/alicyclic brominated compounds 15aliphatic/alicyclic brominated compounds in combination with antimony compounds 16aromatic brominated compounds (excluding brominated diphenyl ether and biphenyls) 17aromatic brominated compounds (excluding brominated diphenyl ether and biphenyls) in com
37、bination with antimony compounds 18polybrominated diphenyl ether 19polybrominated diphenyl ether in combination with antimony compounds 20polybrominated biphenyls 21polybrominated biphenyls in combination with antimony compounds 22aliphatic/alicyclic chlorinated and brominated compounds 23, 24not al
38、located 25aliphatic fluorinated compounds 26 to 29 not allocated Nitrogen compounds: Code 30nitrogen compounds (confined to melamine, melamine cyanurate, urea) 31 to 39 not allocated Organic phosphorus compounds: Code 40halogen-free organic phosphorus compounds 41chlorinated organic phosphorus compo
39、unds 42brominated organic phosphorus compounds 43 to 49 not allocated Inorganic phosphorus compounds: Code 50ammonium orthophosphates 51ammonium polyphosphates 52red phosphorus 53 to 59 not allocated Metal oxides, metal hydroxides, metal salts: Code 60aluminium hydroxide 61magnesium hydroxide 62anti
40、mony(III) oxide 63alkali-metal antimonate 64magnesium/calcium carbonate hydrate 65 to 69 not allocated Licensed Copy: sheffieldun sheffieldun, na, Wed Nov 15 05:38:45 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN ISO 1043-4:1999 BSI 03-20003 Boron and zinc compounds: Code 70inorganic boron compounds
41、 71organic boron compounds 72zinc borate 73organic zinc compounds 74not allocated Silica compounds: Code 75inorganic silica compounds 76organic silica compounds 77 to 79 not allocated Code 80graphite 81 to 89 not allocated Code 90 to 99 not allocated Licensed Copy: sheffieldun sheffieldun, na, Wed N
42、ov 15 05:38:45 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN ISO 1043-4:1999 4 BSI 03-2000 Annex ZA (normative) Normative references to international publications with their relevant European publications This European Standard incorporates by dated or undated reference, provisions from other public
43、ations. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision
44、. For undated references the latest edition of the publication referred to applies. PublicationYearTitleENYear ISO 1043-11997Plastics Symbols and abbreviated terms Part 1: Basic polymers and their special characteristics EN ISO 1043-11999 ISO 1043-31996Plastics Symbols and abbreviated terms Part 3:
45、Plasticizers EN ISO 1043-31999 Licensed Copy: sheffieldun sheffieldun, na, Wed Nov 15 05:38:45 GMT+00:00 2006, Uncontrolled Copy, (c) BSI blank Licensed Copy: sheffieldun sheffieldun, na, Wed Nov 15 05:38:45 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN ISO 1043-4:1999 BSI 389 Chiswick High Road
46、London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment o
47、r revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would in
48、form the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of s
49、tandards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical He