《BS-EN-ISO-119-1998.pdf》由会员分享，可在线阅读，更多相关《BS-EN-ISO-119-1998.pdf（10页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS EN ISO 119:1998 Implementing Amendment No. 1 to BS 2782-4: Method 451E: 1978/ISO 119:1977 (renumbers the BS as BS EN ISO 119:1998), not published separately Plastics Phenol-formaldehyde mouldings Determination of free phenols Iodometric method (ISO 119:1977) ICS 83.140.99 License
2、d Copy: sheffieldun sheffieldun, na, Mon Nov 20 02:09:13 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN ISO 119:1998 BSI 05-1999 ISBN 0 580 10171 1 Foreword This British Standard is technically identical to International Standard ISO 119:1977 Plastics Phenol-formaldehyde mouldings Determination of
3、 free phenols Iodometric method. In 1998 the European Committee for Standardization (CEN) accepted ISO 119:1977 as European Standard EN ISO 119:1998. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correc
4、t application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, the EN ISO title page, pages 2 to 4, an inside back cover and a back cover. This standard has be
5、en updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No.DateComments 10255October 1998Implementing European Standard Licensed Copy: sheffieldun sheffieldun, na, Mon
6、Nov 20 02:09:13 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN ISO 119:1998 BSI 05-1999i Contents Page ForewordInside front cover Foreword2 Text of EN ISO 1193 Publications referred toInside back cover Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 02:09:13 GMT+00:00 2006, Uncontrolled Cop
7、y, (c) BSI ii blank Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 02:09:13 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 119 July 1998 ICS 83.080.10 Descriptors: See ISO document English version Plastics Phenol-formaldehyde mouldings Det
8、ermination of free phenols Iodometric method (ISO 119:1977) Plastiques Pices moules base de phnoplastes Dosage des phnols libres Mthode iodomtrique (ISO 119:1977) Kunststoffe Phenoplast-Formteile Bestimmung der freiem Phenole Iodometrisches Verfahren (ISO 119:1977) This European Standard was approve
9、d by CEN on 12 June 1998. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national stan
10、dards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to
11、 the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and Unit
12、ed Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1998 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members Ref. No. EN ISO 1
13、19:1998 E Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 02:09:13 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN ISO 119:1998 BSI 05-1999 2 Foreword The text of the International Standard from Technical Committee ISO/TC 61, Plastics, of the International Organization for Standardization (ISO)
14、 has been taken over as a European Standard by Technical Committee CEN/TC 249, Plastics, the Secretariat of which is held by IBN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 1999, and
15、conflicting national standards shall be withdrawn at the latest by January 1999. According to CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, G
16、ermany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of the International Standard ISO 119:1977 has been approved by CEN as a European Standard without any modification. Contents Page Forewo
17、rd2 1Scope and field of application3 2References3 3Principle3 4Reagents3 5Apparatus3 6Preparation of test sample3 7Procedure3 8Expression of results4 9Test report4 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 02:09:13 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN ISO 119:1998 BSI 05-19993
18、1 Scope and field of application This International Standard specifies an iodometric method for the semi-quantitative determination of the amount of free phenols in phenol-formaldehyde mouldings. NOTEThis International Standard does not provide an absolute measure of the free phenols present. The am
19、ount of free phenols in a moulded article is influenced to a major extent by the degree of cure. Its evaluation is also of interest where the possibility of contamination of foodstuffs or other materials in contact with the article has to be considered. 2 References ISO/R 385, Burettes. ISO 565, Tes
20、t sieves Woven metal wire cloth and perforated plate Nominal sizes of apertures. ISO 648, Laboratory glassware One-mark pipettes1). 3 Principle Hot aqueous extraction of free phenols from a powdered test portion. Iodination of the aqueous extract by a solution of iodine in the presence of sodium tet
21、raborate. Acidification, then immediate titration of the excess iodine with standard volumetric sodium thiosulphate solution, using a starch solution as indicator. Calculation of the result assuming the reaction of six atoms of iodine with each molecule of phenol. 4 Reagents During the analysis, use
22、 only reagents of recognized analytical grade, and only distilled water or water of equivalent purity. 4.1 Sodium tetraborate, decahydrate (Na2B4O7.10H2O). 4.2 Sulphuric acid, 2 N solution. 4.3 Iodine, about 0,05 N solution. Dissolve 6,35 g of iodine in approximately 40 ml of a 500 g/l solution of p
23、otassium iodide and dilute to 1 000 ml with water. 4.4 Sodium thiosulphate, 0,05 N standard volumetric solution. 4.5 Starch, approximately 2,5 g/l solution. 5 Apparatus Ordinary laboratory apparatus and 5.1 Means for reducing the mouldings to a powder. 5.2 Sieve, with nominal apertures of 250 m, com
24、plying with the requirements of ISO 565. 5.3 Balance, accurate to 0,01 g. 5.4 Glass-stoppered flask, 250 ml capacity. 5.5 Glass-stoppered iodine flask, 250 ml capacity. 5.6 Sintered glass crucible, or filter funnel with sintered disk, of pore size 40 to 90 m. Alternatively a filter funnel with harde
25、ned medium speed filter paper may be used. 5.7 Pipettes, capacities 5 and 10 ml, complying with the requirements of ISO 648. 5.8 Burette, complying with the requirements of ISO/R 385. 6 Preparation of test sample Reduce a fully representative sample of the mouldings to powder by filing, milling, gri
26、nding, turning or drilling, taking care that no undue heating of the material occurs. Sieve the powder thus obtained, using the sieve (5.2), and use for the test that portion passing through the sieve. Keep the sample in a tightly stoppered flask until required. The extraction with water (see 7.3) s
27、hall begin within 1 h of grinding the moulding. NOTEThe method of reduction to powder can affect the results. In cases of dispute, or for referee purposes, the method should be agreed between the interested parties. 7 Procedure 7.1 Test portion Weigh, to the nearest 0,01 g, 5 0,1 g of the sieved mat
28、erial (see clause 6). 7.2 Blank test Carry out a blank test by replacing the 5 ml of aqueous extract (7.3) with 5 ml of water and proceeding exactly as described in 7.4. 7.3 Preparation of the test solution Place the test portion (7.1) in the flask (5.4) and cover it with ten times its mass of water
29、 at a temperature of 90 to 100 C. Stopper the flask and shake it so that the powder is thoroughly wetted. Allow it to cool at room temperature, for 1 h, with occasional shaking. Then filter the contents of the flask through the sintered glass crucible or filter funnel (5.6). 1) At present at the sta
30、ge of draft. (Revision of ISO/R 648.) Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 02:09:13 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN ISO 119:1998 4 BSI 05-1999 7.4 Determination Transfer, with a pipette (5.7), 5 ml of the filtered extract, corresponding to 0,5 g of the powder, to the
31、iodine flask (5.5). Add 10 ml of the iodine solution (4.3) and 3 to 4 g of the sodium tetraborate (4.1), and dilute to about 100 ml with water. Immediately stopper the flask. Allow the mixture to stand for 10 min, and then add 20 to 30 ml of the sulphuric acid solution (4.2). Immediately titrate the
32、 liberated iodine with the sodium thiosulphate solution (4.4), adding 2 ml of the starch solution (4.5) as indicator near the end-point of the titration and continuing until the blue starch/iodine colour has disappeared. A residual pale colour from the mouldings may be present at the end of the titr
33、ation. 8 Expression of results The free phenols content, expressed as a percentage by mass of phenol (C6H5OH), is given by the formula where V1 is the volume, in millilitres, of the sodium thiosulphate solution (4.4) used in the blank test (7.2); V2 is the volume, in millilitres, of the sodium thios
34、ulphate solution (4.4) used for the determination (7.4); T is the normality of the sodium thiosulphate solution (4.4); 0,0157 is the mass, in grams, of phenol corresponding to 1 ml of exactly 1 N sodium thiosulphate solution; 0,5 is the mass, in grams, of the powdered sample corresponding to 5 ml of
35、 filtered extract (see 7.4). If T = 0,05 N, the formula for calculation of free phenols content reduces to 0,157 (V1 V2) 9 Test report The test report shall include the following particulars: a) reference to this International Standard; b) full details necessary for the identification of the sample;
36、 c) the method used for reducing the mouldings to powder; d) amount of free phenols; e) date of the test. Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 02:09:13 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BSI 05-1999 BS EN ISO 119:1998 Publications referred to See national foreword Licensed
37、Copy: sheffieldun sheffieldun, na, Mon Nov 20 02:09:13 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN ISO 119:1998 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on
38、 standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the qu
39、ality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7
40、400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001
41、. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and i
42、nternational standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of B
43、SI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also h
44、olds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, record
45、ing or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the
46、prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070. Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 02:09:13 GMT+00:00 2006, Uncontrolled Copy, (c) BSI