《BS-ISO-6022-1981.pdf》由会员分享，可在线阅读，更多相关《BS-ISO-6022-1981.pdf（14页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS ISO 6022: 1981 Hydraulic fluid power Single rod cylinders Mounting dimensions 250 bar (25 000 kPa) series ICS 23.100.20 Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 06:47:03 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS ISO 6022:1981 This British Standard, having been p
2、repared under the direction of the Engineering Sector Board, was published under the authority of the Standards Board and comes into effect on 15 June 1997 BSI 02-1999 ISBN 0 580 27542 6 National foreword This British Standard reproduces verbatim ISO 6022:1981 and implements it as the UK national st
3、andard. It supersedes BS 6331-3:1983 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee MCE/18, Fluid power systems and components, which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European c
4、ommittee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. Cross-r
5、eferences The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or using the “Find” facility of the BSI Standards Electronic Cata
6、logue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document com
7、prises a front cover, an inside front cover, pages i and ii, the ISO title page, page ii, pages 1 to 6 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments i
8、ssued since publication Amd. No.DateComments Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 06:47:03 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS ISO 6022:1981 BSI 02-1999i Contents Page National forewordInside front cover Forewordii 0Introduction1 1Scope and field of application1 2Referenc
9、es1 3Definitions1 4Dimensions1 5Bore sizes1 6Mounting styles1 7Piston rod characteristics1 8Identification statement2 Bibliography6 Figure 1 General dimensions2 Figure 2 MF3 Head circular flange mounting MF4 Cap circular flange mounting3 Figure 3 MP3 Cap fixed eye mounting MP4 Cap detachable eye mou
10、nting MP5 Cap fixed eye with spherical plain bearing mounting MP6 Cap detachable eye with spherical plain bearing mounting4 Figure 4 MT4 Intermediate fixed or movable trunnion (male)5 Table 1 General dimensions2 Table 2 Dimensions of mounting by circular flange3 Table 3 Dimensions of mounting by cap
11、 eye4 Table 4 Dimensions of mounting by central male trunnion5 Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 06:47:03 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ii blank Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 06:47:03 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Licensed Copy:
12、 sheffieldun sheffieldun, na, Sun Nov 26 06:47:03 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS ISO 6022:1981 ii BSI 02-1999 Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards institutes (ISO member bodies). The work of developing Intern
13、ational Standards is carried out through ISO technical committees. Every member body interested in a subject for which a technical committee has been set up has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also ta
14、ke part in the work. Draft International Standards adopted by the technical committees are circulated to the member bodies for approval before their acceptance as International Standards by the ISO Council. International Standard ISO 6022 was developed by Technical Committee ISO/TC 131, Fluid power
15、systems and components, and was circulated to the member bodies in November 1978. It has been approved by the member bodies of the following countries: The member bodies of the following countries expressed disapproval of the document on technical grounds: Australia Hungary Norway Descriptors: Hydra
16、ulic fluid power, hydraulic equipment, hydraulic cylinders, dimensions, interchangeability, bores, fixing. AustriaIrelandSpain BelgiumItalySweden ChileJapanUnited Kingdom CzechoslovakiaKorea, Rep. ofUSA FinlandNetherlandsUSSR FrancePolandYugoslavia Germany, F. R.Romania IndiaSouth Africa, Rep. of Li
17、censed Copy: sheffieldun sheffieldun, na, Sun Nov 26 06:47:03 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS ISO 6022:1981 BSI 02-19991 0 Introduction In hydraulic fluid power systems, power is transmitted and controlled through a liquid under pressure within an enclosed circuit. One component of suc
18、h systems is the fluid power cylinder. This is a device which converts power into linear mechanical force and motion. It consists of a movable element, i.e. a piston and piston rod, operating within a cylindrical bore. 1 Scope and field of application This International Standard establishes a metric
19、 series of mounting dimensions required for interchangeability of commonly used hydraulic cylinders. NOTEThis International Standard allows manufacturers of hydraulic equipment freedom in the design of metric cylinders and does not restrict technical development but provides basic guidelines. 2 Refe
20、rences ISO 273, Fasteners Clearance holes for bolts and screws. ISO 3320, Fluid power systems and components Cylinder bores and piston rod diameters Metric series. ISO 4395, Fluid power systems and components Cylinders Piston rod thread dimensions and types. ISO 5598, Fluid power systems and compone
21、nts Vocabulary.1) 3 Definitions Definitions of other terms used in this International Standard are given in ISO 5598. 3.1 cylinder a device which converts fluid power into linear mechanical force and motion 3.2 cylinder bore the internal diameter of the cylinder 3.3 piston rod the element transmitti
22、ng mechanical force and motion from the piston 3.4 mounting a device by which a cylinder is fastened to its mating element 4 Dimensions Select mounting dimensions for cylinders manufactured in accordance with this International Standard from Table 1 to Table 4 inclusive. 5 Bore sizes Included in thi
23、s 250 bar series are the following bore sizes: 50 63 80 100 125 160 200 250 320 400 500 mm 6 Mounting styles This International Standard includes the following mounting styles: 7 Piston rod characteristics 7.1 This International Standard covers piston rods having a shouldered male thread end (see Fi
24、gure 1 and Table 1 for basic dimensions). 7.2 For internally threaded rod ends, see ISO 4395. 7.3 For rod end eyes, International Standards are being prepared. 1) At present at the stage of draft. MF3 Head circular flange mounting (see Figure 2 and Table 2) MF4 Cap circular flange mounting (see Figu
25、re 2 and Table 2) MP3 Cap fixed eye mounting (see Figure 3 and Table 3) MP4 Cap detachable eye mounting (see Figure 3 and Table 3) MP5 Cap fixed eye with spherical plain bearing mounting (see Figure 3 and Table 3) MP6 Cap detachable eye with spherical plain bearing mounting (see Figure 3 and Table 3
26、) MT4 Intermediate fixed or movable trunnion (male) mounting (see Figure 4 and Table 4). Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 06:47:03 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS ISO 6022:1981 2 BSI 02-1999 8 Identification statement (Reference to this International Standard) Use
27、 the following statement in test reports, catalogues and sales literature when electing to comply with this International Standard: “Interchangeable cylinder mounting dimensions selected in accordance with ISO 6022, Hydraulic fluid power Single rod cylinders Mounting dimensions 250 bar (25 000 kPa2)
28、 series”. Table 1 General dimensions 2) 1 kPa = 1 N/m2 Figure 1 General dimensions Dimensions in millimetres Bore506380100125160200250320400500 MM32 to 3640 to 4550 to 5663 to 7080 to 90100 to 110125 to 140160 to 180200 to 220250 to 280320 to 360 ZJ240270300335390460540640750755900 KKM27 2M33 2M42 2
29、M48 2M64 3M80 3M100 3M125 4M160 4M200 4M250 6 A364556638595112125160200250 VE293236414550617188110135 WF475360687685101113136163195 NOTEIf other piston rod diameters or other threads are required, use those identified in ISO 3320 and ISO 4395. Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 0
30、6:47:03 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS ISO 6022:1981 BSI 02-19993 Table 2 Dimensions of mounting by circular flange Figure 2 MF3 Head circular flange mounting MF4 Cap circular flange mounting Dimensions in millimetres Bore506380100125160200250320400500 FB8 f 13,5 8 f 13,5 8 f 17,58 f
31、228 f 228 f 268 f 338 f 398 f 4512 f 4512 f 52 FC 132150180212250315385475600720840 VD min. 4445555881010 WC 2225283236404550566370 ZP 2652983323714305055967038308551 025 ZB max. 244274305340396467550652764775932 B, BA637590110132160200250320400500 Licensed Copy: sheffieldun sheffieldun, na, Sun Nov
32、 26 06:47:03 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS ISO 6022:1981 4 BSI 02-1999 Table 3 Dimensions of mounting by cap eye Figure 3 MP3 Cap fixed eye mounting MP4 Cap detachable eye mounting MP5 Cap fixed eye with spherical plain bearing mounting MP6 Cap detachable eye with spherical plain bea
33、ring mounting Dimensions in millimetres Bore506380100125160200250320400500 CDa or CXb3240506380100125160200250320 EWa or EXb3240506380100125160200250320 La or LTb min.4050637190112160200250320375 MRa or MSb max.4050637190112160200250320375 XC, XD, XO or XNc3053483954425206177569031 0801 0751 275 Til
34、ting angle Z4 a The dimensions CD, EW, L and MR are valid for mounting types MP3 and MP4. b The dimensions CX, EX, LT and MS are valid for mounting types MP5 and MP6. c The dimension XC is valid for mounting type MP3, the dimension XD is valid for mounting type MP4, the dimension XO is valid for mou
35、nting type MP5 and the dimension XN is valid for mounting type MP6. Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 06:47:03 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS ISO 6022:1981 BSI 02-19995 Table 4 Dimensions of mounting by central male trunnion Figure 4 MT4 Intermediate fixed or mova
36、ble trunnion (male) Dimensions in millimetres Bore506380100125160200250320400500 TD f83240506380100125160200250320 TL J16253240506380100125160200250 TM h12112125150180224280335425530630760 XV(Variable) ZB max.244274305340396467550652764775932 Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 06
37、:47:03 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS ISO 6022:1981 6 BSI 02-1999 Bibliography The following document served as a reference in the preparation of this International Standard and will be helpful in the utilization of the standard: ISO 4393, Fluid power systems and components Cylinders
38、Basic series of piston strokes. Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 06:47:03 GMT+00:00 2006, Uncontrolled Copy, (c) BSI blank Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 06:47:03 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BSI 389 Chiswick High Road London W4 4AL | | | |
39、 | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independ
40、ent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they p
41、ossess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the iden
42、tity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and fo
43、reign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Info
44、rmation on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact
45、 the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7
46、002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a ret
47、rieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designat
48、ions. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070. Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 06:47:03 GMT+00:00 2006, Uncontrolled Copy, (c) BSI