《BS-MA-6-1970.pdf》由会员分享，可在线阅读，更多相关《BS-MA-6-1970.pdf（12页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD MARINE SERIES BS MA 6:1970 Specification for Internal doors and frames UDC 629.12.011.66 Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 02:13:47 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS MA 6:1970 This British Standard, having been approved
2、 by the Shipbuilding & Marine Industry Standards Committee, was published under the authority of the Executive Board on 30 July 1970 BSI 02-2000 The following BSI references relate to the work on this standard: Committee reference SME/2 Draft for approval 69/8829 ISBN 0 580 06172 8 Foreword This Bri
3、tish Standard has been prepared under the authority of the Shipbuilding and Marine Industry Standards Committee and is based on a proposal of the British Ship Research Association. This standard makes reference to the following British Standards: BS 4011, Recommendations for the co-ordination of dim
4、ensions in building. BS 459, Doors Part 3: Plywood faced fire-check flush doors and wood and metal frames. CP 151, Doors and windows, including frames and linings Part 1: Wooden doors. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standar
5、ds are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages 1 to 6, an inside back cover and a back cover. This sta
6、ndard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No.DateComments Licensed Copy: London South Bank University, London South Bank University, Sat Dec 0
7、9 02:13:47 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS MA 6:1970 BSI 02-2000i Contents Page ForewordInside front cover 1Scope1 2Types and dimensions1 3Construction1 4Ancillary fittings1 5Marking1 6Information to be supplied with an enquiry or order1 Figure 1 Internal doors: Type 1, Standard door a
8、nd frame3 Figure 2 Internal doors: Type 2, Standard door and frame with coaming4 Figure 3 Internal doors: Sectional dimensions for standard hardwood frame5 Table 1 Internal doors: Principal dimensions, types 1 & 22 Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09
9、 02:13:47 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ii blank Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 02:13:47 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS MA 6:1970 BSI 02-20001 NOTEUsers of this British Standard, Marine Series, should note that while
10、observing the requirements of the standard they should at the same time ensure compliance with such statutory requirements, rules and regulations as may be applicable to the individual ship concerned. 1 Scope 1.1 This British Standard relates to all internal doors installed on board ships, with the
11、exception of A Class (SOLAS) and small cupboard doors. 1.2 The standard specifies dimensions for two basic types of doors, in three nominal sizes of 600 mm, 700 mm and 800 mm. 1.3 The standard does not specify either materials or details of door furniture. 2 Types and dimensions 2.1 The types of int
12、ernal doors and frames, constructed in accordance with this British Standard, are as follows: Type 1. Standard door and frame, fitting directly to the deck. Type 2. As Type 1 but modified to accommodate a raised sill or coaming. The principal dimensions shall be as set out in Table 1 and the dimensi
13、oned sketches shown in Figure 1 and Figure 2. The nominal size of the door is taken from the door width, dimension a of Table 1. 2.2 The dimensions given in Table 1 are related to the overall dimensions of the doors and frames. The allowable tolerance for these overall dimensions shall be plus or mi
14、nus 1 mm. 2.3 The details of the door frame sections shall be as shown in Figure 3. These are related to the external finished sizes across the frame which, in turn, correspond to the 100 mm modular system as recommended for the Construction Industry in BS 4011. The dimensions are shown for a standa
15、rd hardwood frame, but where metal or composite frames are utilized they shall also comply with these dimensions, in order to ensure uniformity of appearance in accordance with the modular system. 3 Construction 3.1 The construction of the doors and frames shall comply generally with the requirement
16、s in BS 459-3 and with the provisions of British Standard Code of Practice CP 151-1. 3.2 Homogeneous panel cores, such as asbestos based materials and chipboard, shall have hardwood lippings glued on both long edges. No metal fasteners shall be used for fixing them. 3.3 The door facings shall comply
17、 with all requirements for limitation of combustible veneers and surface spread of flame. 3.4 The door shall be carefully fitted and hung in the frame in such a manner that, when in the closed position, the gap between the edge of the door and the frame is not more than 3 mm wide at any point. 3.5 T
18、he dimension stated for the overall height of the door frame (Table 1) is the mean finished height and an allowance is necessary for variations due to sheer, camber, and deck coverings. It is recommended therefore, that Type 1 frames should be supplied with the main side frames 50 mm oversize in len
19、gth. 4 Ancillary fittings 4.1 Each door shall be hung with either two or three hinges, in the positions indicated in Figure 1 and Figure 2. 4.2 Locks and latches shall be so fitted that the handle conforms to the standard position as shown in Figure 1 and Figure 2. 4.3 The stops of the door frames s
20、hall not, in any circumstances, be cut away to facilitate the use of locks with a small back-set of the key and follower. 5 Marking The doors shall be marked on the hanging stile with the following particulars: 1) The number of this British Standard, i.e. BS MA 6. 2) The type number, i.e. Type 1, or
21、 Type 2. 3) Nominal size (see Table 1). 4) Class for which it is approved (see 1 Scope). 6 Information to be supplied with an enquiry or order The following information shall be supplied by the purchaser when making an enquiry or placing an order: 1) The number of this British Standard, i.e. BS MA 6
22、. 2) The Type number, i.e. Type 1, or Type 2. 3) The nominal size (see Table 1). 4) The Class for approval, including material and thickness. 5) The surface finish on “pull” side. 6) The surface finish on “push” side. 7) The frame finish on “pull” side. 8) The frame finish on “push” side. Licensed C
23、opy: London South Bank University, London South Bank University, Sat Dec 09 02:13:47 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS MA 6:1970 2 BSI 02-2000 Table 1 Internal doors: Principal dimensions, types 1 & 2 All dimensions are in millimetres Nominal size600700800 Type of door121212 Door width a
24、600600700700800800 Door height1 9251 8501 9251 8501 9251 850 Sill height at centre989898 Height to bottom of door at centre251002510025100 Clear width b568568668668768768 Clear height above deck at centre1 9341 9341 9341 9341 9341 934 Overall frame width c700700800800900900 Overall frame height at c
25、entre 2 0002 0002 0002 0002 0002 000 Door handle height above deck at centre1 0001 0001 0001 0001 0001 000 Bulkhead aperture width d664664764764864864 Bulkhead aperture height above deck at centre1 9821 9821 9821 9821 9821 982 Licensed Copy: London South Bank University, London South Bank University
26、, Sat Dec 09 02:13:47 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS MA 6:1970 BSI 02-20003 Figure 1 Internal doors: Type 1, Standard door and frame Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 02:13:47 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS MA 6:1970 4
27、 BSI 02-2000 NOTEThe requirements for type 2 doors are identical with Type 1 with the exception of the length viz. 1 850 mm. Figure 2 Internal doors: Type 2, Standard door and frame with coaming Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 02:13:47 GMT+00:00
28、2006, Uncontrolled Copy, (c) BSI BS MA 6:1970 BSI 02-20005 Figure 3 Internal doors: Sectional dimensions for standard hardwood frame Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 02:13:47 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 6 blank Licensed Copy: London
29、 South Bank University, London South Bank University, Sat Dec 09 02:13:47 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS MA 6:1970 BSI 02-2000 BSI Certification trade mark (The Kitemark) The British Standards Institution is the owner of a registered certification trade mark. It is usually associated
30、with the words “approved to British Standard” as shown below, the number of the relevant British Standard being added. This mark may be used only by those licensed under the certification mark scheme operated by BSI. The presence of this mark on or in relation to a product is an assurance that the g
31、oods have been produced under a system of supervision, control and testing, operated during manufacture and including periodical inspection of the manufacturers works in accordance with the certification mark scheme of BSI designed, to ensure compliance with a British Standard. Further particulars o
32、f the terms of licence may be obtained from the Certification Marks Section, British Standards Institution, 2 Park Street, London, WIY 4AA. Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 02:13:47 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS MA 6:1970 BSI 389 C
33、hiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are upda
34、ted by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British
35、 Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the la
36、test editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of
37、those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information ser
38、vices are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For d
39、etails of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the
40、Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing
41、 the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070. Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 02:13:47 GMT+00:00 2006, Uncontrolled Copy, (c) BSI