《BS-ISO-1268-1-2001.pdf》由会员分享，可在线阅读，更多相关《BS-ISO-1268-1-2001.pdf（12页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS ISO 1268-1:2001 Fibre-reinforced plastics Methods of producing test plates Part 1: General conditions ICS 83.120 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 27 08:12:57 GMT+00:00 2006, Uncontrolled Cop
2、y, (c) BSI BS ISO 1268-1:2001 This British Standard, having been prepared under the direction of the Materials and Chemicals Sector Policy and Strategy Committee, was published under the authority of the Standards Policy and Strategy Committee on 30 January 2002 BSI 30 January 2002 ISBN 0 580 38902
3、2 National foreword This British Standard reproduces verbatim ISO 1268-1:2001 and implements it as the UK national standard. The UK participation in its preparation was entrusted to Technical Committee PRI/42, Fibre reinforced thermosetting plastics and prepregs, which has the responsibility to: A l
4、ist of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “Internati
5、onal Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a Brit
6、ish Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international an
7、d European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the ISO title page, pages ii to iv, pages 1 to 4, an inside back cover and a back cover. The BSI copyright date displayed in this document indicates when the document
8、 was last issued. Amendments issued since publication Amd. No. DateComments Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 27 08:12:57 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Reference number ISO 1268-1:2001(E) INTERNATIONAL STANDARD ISO 1268-1 First edition 2001-12-01 Fibre-reinforced plast
9、ics Methods of producing test plates Part 1: General conditions Plastiques renforcs de fibres Mthodes de fabrication de plaques dessai Partie 1: Conditions gnrales Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 27 08:12:57 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO 1268-1:2001(E) ii License
10、d Copy: sheffieldun sheffieldun, na, Mon Nov 27 08:12:57 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO 1268-1:2001(E) iii Contents Page Foreword.iv 1 Scope1 2 Normative references1 3 Terms and definitions .2 4 Health and safety.2 5 Principle2 6 Raw materials and semi-finished products 2 7 Plate dim
11、ensions .2 8 Reinforcement2 9 General requirements for the laboratory/workshop apparatus2 10 Procedure.3 11 Verification of the characteristics of the plates obtained .3 12 Marking.3 13 Test plate preparation report4 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 27 08:12:57 GMT+00:00 2006, Unc
12、ontrolled Copy, (c) BSI ISO 1268-1:2001(E) iv Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each mem
13、ber body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International El
14、ectrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. The main task of technical committees is to prepare International Standards. Draft International Standards ado
15、pted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this part of ISO 1268 may be the subjec
16、t of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 1268-1 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 13, Composites and reinforcement fibres. Together with the other parts (see below), this part of ISO 1268 cancels a
17、nd replaces ISO 1268:1974, which has been technically revised. ISO 1268 consists of the following parts, under the general title Fibre-reinforced plastics Methods of producing test plates: Part 1: General conditions Part 2: Contact and spray-up moulding Part 3: Wet compression moulding Part 4: Mould
18、ing of prepregs Part 5: Filament winding Part 6: Pultrusion moulding Part 7: Resin transfer moulding Part 8: Compression moulding of SMC and BMC Part 9: Moulding of GMT/STC Part 10: Injection moulding of SMC and other long-fibre moulding compounds General principles and moulding of multipurpose test
19、 specimens Part 11: Injection moulding of SMC and other long-fibre moulding compounds Small plates Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 27 08:12:57 GMT+00:00 2006, Uncontrolled Copy, (c) BSI INTERNATIONAL STANDARD ISO 1268-1:2001(E) 1 Fibre-reinforced plastics Methods of producing tes
20、t plates Part 1: General conditions 1 Scope The various parts of ISO 1268 (see the foreword) describe methods used to prepare reinforced-plastics plates from which test specimens can be cut. This allows the properties of a composite, or the constituents of the composite, to be determined. The method
21、s are intended to cover all the main types of reinforcement and resin matrix. The choice of test plate preparation method depends on: a) the reinforcement: its nature (glass, carbon, aramid, etc.); its form (roving, mat, woven fabric, etc.); its orientation with respect to the length, width and thic
22、kness of the plate; its content in the reinforced plastic; b) the matrix (thermosetting or thermoplastic); c) the magnitude expected for the properties; d) the production process that is to be evaluated. Since the mechanical properties of a reinforced plastic are known to be dependent on the process
23、 by which the plastic is produced, it is recommended that the test plates be prepared, if possible, by the same method that will be used to produce the plastic. This part of ISO 1268 describes the general requirements common to all the methods. 2 Normative references The following normative document
24、s contain provisions which, through reference in this text, constitute provisions of this part of ISO 1268. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this part of ISO 1268 are encouraged to investi
25、gate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards. ISO 472, Plastics Voca
26、bulary ISO 1172, Textile-glass-reinforced plastics Prepregs, moulding compounds and laminates Determination of the textile-glass and mineral-filler content Calcination methods Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 27 08:12:57 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO 1268-1:2001(E
27、) 2 ISO 1183 (all parts), Plastics Methods for determining the density of non-cellular plastics ISO 7822, Textile glass reinforced plastics Determination of void content Loss on ignition, mechanical disintegration and statistical counting methods ISO 10724-2:1998, Plastics Injection moulding of test
28、 specimens of thermosetting powder moulding compounds (PMCs) Part 2: Small plates 3 Terms and definitions For the purposes of this part of ISO 1268, the terms and definitions given in ISO 472 apply. Each subsequent part of ISO 1268 gives, where necessary, the definitions of specific terms it needs t
29、o introduce. 4 Health and safety The various parts of ISO 1268 are limited to describing test plate preparation methods. The conditions under which the materials used are handled shall comply with the national regulations in force in each country and the staff shall be informed of the hazards involv
30、ed and appropriate precautions taken. 5 Principle Subsequent parts of this International Standard describe the basic methods utilized to produce test plates. 6 Raw materials and semi-finished products All the materials used (reinforcements, resins, additives; SMC, BMC, prepregs, etc.) shall be ident
31、ified in a precise manner. They shall be stored under the conditions recommended by the manufacturer and shall be used before the expiration date marked on the label. 7 Plate dimensions The length, width and thickness of the plates produced will depend on the material being processed and the method
32、used to produce them. The dimensions shall be as specified in the relevant part of this Intenational Standard. NOTE The plate dimensions will also depend on the test which will be conducted on the test specimens cut from the plates. For example, a square plate of side at least 250 mm is required to
33、perform tensile tests in two perpendicular directions. 8 Reinforcement The reinforcement content of the plate shall be the same as in the finished products whose properties are to be evaluated. In the absence of particular specifications, use the recommended content given in the relevant part of thi
34、s International Standard. 9 General requirements for the laboratory/workshop apparatus Unless otherwise specified, the apparatus used to produce the plates shall be capable of maintaining the required temperatures and pressures to within the accuracy prescribed for the chosen plate production method
35、. Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 27 08:12:57 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO 1268-1:2001(E) 3 The laboratory/workshop shall be equipped with monitoring equipment which will enable the production temperature and pressure to be recorded as a function of time. 10 Pro
36、cedure The procedure used to prepare the test plates will differ depending on the process and materials used. The procedure to be followed for a particular plate production method is described in the relevant part of this International Standard. 11 Verification of the characteristics of the plates o
37、btained 11.1 General The plates obtained shall be inspected prior to cutting out test specimens. The criteria for acceptance or rejection of a plate shall be as defined in the materials specifications and in the plate production method, or as agreed between the interested parties. 11.2 Fibre content
38、 The fibre content shall be determined in accordance with ISO 1172 for glass-reinforced plastics and by a method agreed on between the interested parties for carbon-reinforced plastics. The lay-up sequence can be determined by examination of the residue. 11.3 Degree of porosity or void content The d
39、egree of porosity, or void content, is a measure of the frequency of occurrence of open or closed cavities in the plate. Any of several methods may be used to determine it: visual examination, examination of a polished cross-section using a microscope (see ISO 7822), ultrasonic examination or X-ray
40、examination. 11.4 Density The density may be determined in accordance with the appropriate part of ISO 1183. 11.5 Dimensions The thickness of the plates shall be measured and, where necessary, the other dimensions. 12 Marking Each plate shall be marked to allow the identification of the mould or the
41、 mould cavity used; the side of the plate; the lay-up sequence, if required; the orientation of the plate with respect to the melt flow direction, or to any other direction specific to the material or the method of production. Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 27 08:12:57 GMT+00:00
42、 2006, Uncontrolled Copy, (c) BSI ISO 1268-1:2001(E) 4 The system of lines (thin or broad, single or multiple) described in ISO 10724-2:1998, annex C, shall be used. In addition, plates shall have markings enabling the plate preparation report to be easily traced. 13 Test plate preparation report Th
43、e test plate preparation report shall indicate the following information: a) a reference to the relevant part of this International Standard; b) the place and date of production of the plate or plates; c) a full description of the materials used, including details of resins, reinforcements, fillers,
44、 etc.; d) the composition of the resin system used, where applicable; e) a description of the equipment used; f) details of the operating conditions; g) details of the lay-up of the plate or plates; h) the values of the test plate characteristics (e.g. thickness, fibre content) which the relevant pa
45、rt of this International Standard requires to be determined and any other characteristics when applicable (see clause 11); i) any other information needed to reproduce the plates exactly; j) any deviations from the relevant part of this International Standard. Licensed Copy: sheffieldun sheffieldun,
46、 na, Mon Nov 27 08:12:57 GMT+00:00 2006, Uncontrolled Copy, (c) BSI blank Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 27 08:12:57 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS ISO 1268-1:2001 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent na
47、tional body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess
48、 the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity o
49、f which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI websi